Jonsered BP2040C Operator's Manual
  1. Manuals
  2. Brands
  3. Jonsered Manuals
  4. Trimmer
  5. BP2040C
  6. Operator's manual
Jonsered BP2040C Operator's Manual

Jonsered BP2040C Operator's Manual

Trimmers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Operator´s manual
(EPA)
Please read these instructions carefully and
make sure you understand them before
using the machine.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BP2040C and is the answer not in the manual?

Questions and answers

Related Manuals for Jonsered BP2040C

Summary of Contents for Jonsered BP2040C

  • Page 1 Operator´s manual (EPA) Please read these instructions carefully and make sure you understand them before using the machine.

  • Page 2: Symbol Explanation

    SYMBOL EXPLANATION Symbols Always wear approved protective WARNING! Clearing saws, gloves. brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Use anti-slip and stable boots. Read through the Operator‘s Manual carefully and understand the content before using the machine.

  • Page 3: Table Of Contents

    CONTENTS Jonsered has a policy of continuous product development and List of contents therefore reserves the right to modify the design and appearance of products without prior notice. SYMBOL EXPLANATION Symbols ................2 CONTENTS Maintenance, replacement, or repair of the emission control List of contents ..............

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment The machine‘s safety equipment This section describes the machine‘s safety equipment, its IMPORTANT INFORMATION function and how checks and maintenance are carried out to • A clearing saw, brushcutter or trimmer used ensure that it operates correctly. (See the chapter “What is incorrectly or carelessly can become a dangerous what“...
  • Page 5 SAFETY INSTRUCTIONS 6. Muffler 4. Vibration damping system The muffler is designed to give the lowest possible noise Your machine is equipped level and to direct the with a vibration damping engine‘s exhaust fumes away system, which is designed to from the operator.

  • Page 6: Control, Maintenance And Service Of The Machine's Safety Equipment

    SAFETY INSTRUCTIONS Control, maintenance and service of 3. Cutting attachment guard the machine‘s safety equipment • Check that the guard is IMPORTANT INFORMATION undamaged and not cracked. • All service and repairs to the machine require special training. • Replace the guard if it •...
  • Page 7 SAFETY INSTRUCTIONS 6. Cutting equipment 7. Quick-release This section describes how through correct maintenance and • Check that the harness through using the right type of cutting equipment you can: straps are correctly • Reduce the machine‘s tendency to kickback positioned.

  • Page 8: Cutting Equipment

    SAFETY INSTRUCTIONS Cutting equipment Trimmer head IMPORTANT INFORMATION • Only use a trimmer head and trimmer cord that is The section describes how through correct recommended. These maintenance and through using the right type of have been tested by the cutting equipment you can reduce the machine‘s manufacturer to suit a tendency to kickback, obtain maximum clearing...

  • Page 9: General Safety Instructions

    SAFETY INSTRUCTIONS General safety instructions Fuel safety IMPORTANT INFORMATION • Always use a fuel container • The machine is only designed for trimming grass with an anti-spill valve. and brush cutting. • The only accessories to be used with the engine •...

  • Page 10: General Working Instructions

    SAFETY INSTRUCTIONS General working instructions Adjusting the harness and clearing saw IMPORTANT INFORMATION WARNING! When working with the clearing saw the • This section takes up the basic safety harness should always be worn. If this is precautions for working with the clearing saw not done, you cannot control the clearing and trimmer.

  • Page 11: Basic Clearing Techniques

    SAFETY INSTRUCTIONS Basic clearing techniques Brush cutting using a grass blade • A blade is used for all • Always carry out clearing and trimming at full throttle. types of high or thick grass. • Always drop to idling speed after each working operation. Longer periods running at full throttle without loading the •...
  • Page 12 SAFETY INSTRUCTIONS Grass trimming using the trimmer head Trimming and plastic blades • The trimmer is ideal to cut grass that is difficult to • Hold the trimmer head reach using a normal lawn just above the ground at mower. Keep the cord an angle.

  • Page 13: What Is What

    WHAT IS WHAT? What is what on the grass trimmer/brushcutter? Blade Locking nut Grease filler cap Support flange Angle gear Support cup Spray guard Drive disc Shaft J-handle Off-loading strap Shaft coupling Throttle Socket spanner Stop switch Operator‘s Manual Throttle trigger lock Transport guard Cylinder cover Allen key...

  • Page 14: Assembly

    ASSEMBLY Assembling the J-handle and off- Assembly of the blade and trimmer loading strap head It is extremely important WARNING that the disc drive’s/support Only grass blades or trimmer heads/ flange’s guide engages plastic blades may be used when the J- correctly in the cutting handle is fitted.

  • Page 15: Assembling The Spray Guard And Trimmer Head Auto 32

    ASSEMBLY Assembling the spray guard and Assembling other guards and trimmer head Auto 32 cutting equipment • Fit the guard (A) intended • Fit the guard (A) intended for use with the trimmer for use with the trimmer head. Secure using the 4 head.

  • Page 16: Assembling And Dismantling The Two-Part Shaft

    ASSEMBLY Assembling and dismantling the Adjusting the harness and clearing two-part shaft Assembling: WARNING! When working with the clearing saw the • Make sure the handle is harness should always be worn. If this is loose. not done, you cannot control the clearing saw safely and this can result in injury to •...

  • Page 17: Fuel Handling

    Mixing ratio 1:50 (2%). Gasoline 2%(1:50) • If JONSERED two-stroke oil is not available you can use a Lit. Lit. high quality two-stroke oil intended for air cooled engines. 0,10 Contact your dealer when selecting an oil.

  • Page 18: Start And Stop

    START AND STOP Cold engine Control before starting IGNITION: Set the stop switch to the start position. For reasons of safety follow CHOKE: Set the choke these recommendations! control in the choke posi- tion. • Check the blade to ensure AIR PURGE: that no cracks have formed Press the air purge...

  • Page 19: Maintenance

    • The carburetor is set to its basic setting when test run at the factory. The basic setting is richer than the optimal setting Your JONSERED product has been designed and and should be kept during the machine‘s first working manufactured to specifications that reduce harmful emissions.
  • Page 20 MAINTENANCE Final setting of the idling speed T Correctly adjusted carburetor Adjust the idling speed with A correctly adjusted carburetor means that the machine the screw T, if it is necessary accelerates without hesitation and the machine 4-cycles a to readjust. First turn the little at max speed.

  • Page 21: Muffler

    MAINTENANCE Muffler Cooling system To maintain as low an NOTE! Some mufflers are fitted with a catalytic converter. See operating temperature as “Technical data“ to see whether your machine is fitted with a possible the engine is catalytic converter. equipped with a cooling system.

  • Page 22: Drive Shaft

    MAINTENANCE Drive shaft • Slide the drive shaft back The flexible drive shaft is lubricated with special grease (art. into the sleeve. Make sure no. 5038017-01). The shaft must be lubricated at least every the shaft engages correctly 30 working hours. A tube of drive shaft grease is supplied with by turning it and pushing every machine.

  • Page 23: Angle Gear

    3/4 with grease. Use before you start to work on it. JONSERED special grease. Normally, the grease does • See the cutting not need to be changed equipment’s packaging...

  • Page 24: Maintenance Schedule

    MAINTENANCE NOTE: Use only JONSERED replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically recommended by JONSERED.

  • Page 25: Technical Data

    1/2 idle and 1/2 max. speed. NOTE! Sound pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. Approved accessories BP2040C Type Cutting attachment guard Art No.

  • Page 26: Emission Control Warranty Statement

    As the small off-road engine owner, you should however servicing dealer or call Jonsered, at Sweden +46 36 14 65 00. be aware that Jonsered may deny you warranty coverage if your small off-road engine or a part has failed due to...
  • Page 27 Auto 32 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 " English –...
  • Page 28 Poly Trim >20mm >20mm 6 Nm X 10 – English...
  • Page 29 Tap-N-Go Pro 7,5 m 15 cm 6" ~ 3,7 m 15 cm 6" 15 cm “Click” 6" English –...
  • Page 30 Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6" – English...
  • Page 31 Trimmy SII 7,0 m 12 cm 5" ~ 3,5 m ~ 15 cm "Clic" 35-50 NM English –...
  • Page 32 Trimmy SII ~ 15 cm ~ 15 cm 502 26 04-01 502 25 56-01 502 25 53-01 729 53 27-71 (x3) 738 21 03-04 502 26 24-01 (x2) 740 43 14-00 502 26 03-01 502 25 52-01 502 26 01-01 735 31 19-00 502 27 07-01 502 26 86-01...
  • Page 33 English –...
  • Page 34 ´*xt)¶5h¨ – English...
  • Page 36 108 88 40-95 ´*xt)¶5h¨ 2002W08...

Table of Contents