Related Manuals for Jonsered GT2123
Summary of Contents for Jonsered GT2123
- Page 1 Operator′s manual Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
-
Page 2: Key To Symbols
Symbols WARNING! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 3: Table Of Contents
CONTENTS Contents ... Note the following before starting: ... INTRODUCTION Dear Customer, ... WHAT IS WHAT? What is what on the brush cutter? ... GENERAL SAFETY PRECAUTIONS Important ... Personal protective equipment ... Machine′s safety equipment ... Cutting equipment ... -
Page 4: Introduction
If you will sell this machine, make sure that the buyer will get the operator′s manual. Good luck on using your Jonsered machine! Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. -
Page 5: What Is What On The Grass Trimmer
What is what on the grass trimmer? 1 Trimmer head 2 Cord cutter 3 Cutting attachment guard 4 Shaft 5 Loop handle 6 Throttle control 7 Stop switch 8 Starter handle 9 Fuel tank 10 Choke control WHAT IS WHAT? 11 Air purge 12 Air filter cover 13 Clutch cover... -
Page 6: General Safety Precautions
GENERAL SAFETY PRECAUTIONS Important IMPORTANT! The machine is only designed for trimming grass. The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data. Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination. -
Page 7: Machine's Safety Equipment
GENERAL SAFETY PRECAUTIONS Machine′s safety equipment This section describes the machine′s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positioned on your machine. -
Page 8: Cutting Equipment
GENERAL SAFETY PRECAUTIONS Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: • Reduce the risk of blade thrust. • Obtain maximum cutting performance. • Extend the life of cutting equipment. IMPORTANT! Only use cutting attachments with the guards we recommend! See the chapter on Technical data. -
Page 9: Assembly
Fitting the main body Connect the engine (A) to the tube (B) with four screws (C). Connecting throttle cable and stop switch wires 1 Fit the plastic tube (B) around the throttle cable and stop switch wires as shown. 2 Insert the throttle cable through the cable adjuster sleeve on the carburettor bracket. -
Page 10: Assembling The Cutting Equipment
Assembling the cutting equipment WARNING! Never use a cutting attachment without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury. Fitting the trimmer guard and trimmer head •... -
Page 11: Fuel Handling
When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use JONSERED two- stroke engine oil, which is specially formulated for our air- cooled two-stroke engines. • Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW). -
Page 12: Fuelling
Mixing • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. •... -
Page 13: Starting And Stopping
STARTING AND STOPPING Check before starting • Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard nor with a defective guard. -
Page 14: General Working Instructions
General working instructions IMPORTANT! This section takes up the basic safety precautions for working with a trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. Avoid all usage which you consider to be beyond your capability. -
Page 15: Grass Trimming With A Trimmer Head
Grass trimming with a trimmer head Trimming • Hold the trimmer head just above the ground at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Never press the cord into the area to be cut. -
Page 16: Carburettor
Carburettor Your Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. To ensure that the engine runs at peak performance and... -
Page 17: Cooling System
Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Cooling fins on the cylinder. 2 Cylinder cover (directs cold air over the cylinder). Clean the cooling system with a brush once a week, more often in demanding conditions. -
Page 18: Maintenance Schedule
Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by an authorized service workshop. -
Page 19: Technical Data Technical Data
Note 2: Reported data for equivalent sound pressure level for the machine has a typical statistical dispersion (standard deviation) of 1 dB (A). Note 3: Reported data for equivalent vibration level has a typical statistical dispersion (standard deviation) of 1 m/s Approved accessories Trimmer head TECHNICAL DATA GT2123 22,8 32,2 3000 10000 10000... -
Page 20: Ec-Declaration Of Conformity
EC-declaration of conformity (Applies to Europe only) We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the grass trimmers Jonsered GT2123 with serial numbers dating from 2009 onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:... - Page 24 Original instructions 1153405-26 ´®z+UHT¶6_¨ ´®z+UHT¶6_¨ 2010-02-26...
Need help?
Do you have a question about the GT2123 and is the answer not in the manual?
Questions and answers