Team Losi mini SCT Operation Manual
Team Losi mini SCT Operation Manual

Team Losi mini SCT Operation Manual

1/16-scale electric rtr short course truck
Hide thumbs Also See for mini SCT:

Advertisement

Quick Links

Operation Manual
Not responsible for errors.
Losi, a Division of Horizon Hobby, Inc.
Before operating this vehicle, please read all printed materials thoroughly.

Advertisement

Table of Contents
loading

Summary of Contents for Team Losi mini SCT

  • Page 1 Operation Manual Not responsible for errors. Losi, a Division of Horizon Hobby, Inc. Before operating this vehicle, please read all printed materials thoroughly.
  • Page 2: Meaning Of Special Language

    Introduction Thank you for choosing the Mini SCT from Losi. This guide contains the basic instructions for operating your new Mini SCT. It is critical that you read all of the instructions in order to operate your model correctly and avoid unnecessary damage.
  • Page 3: Charging Warnings And Precautions

    Charging Warnings and Precautions Getting Started Failure to exercise caution while using this product and Step 1 comply with the following warnings could result in product malfunction, electrical issues, excessive heat, FIRE, and ultimately injury and property damage. • Read all safety precautions and literature prior to use of this product.
  • Page 4 Step 4 Step 7 Install the charged battery pack into the chassis as shown. Ensure the battery is laying flat on the chassis. Once the transmitter has been powered on, turn on your Step 5 vehicle by sliding the switch on the ESC to the “ON” position. Step 8 Left Right...
  • Page 5: Safety Precautions

    Losi Mini SCT radio system. This interference may cause momentary loss of control Since the Mini SCT operates on a radio signal, it is important so it is advisable to always keep some distance in all...
  • Page 6: The Transmitter

    Re-Binding the Transmitter the tRANSMitteR to the Receiver The Losi DSM radio system included in the Mini SCT operates on 2.4GHz. The communication between the transmitter and receiver starts in the few seconds after the transmitter and vehicle are both turned on. This is called the “binding process”.
  • Page 7: Speed Control Programming

    Resetting and adjusting the Battery Type Programming MSC-18BL ESC C. LED indicator After power is turned on, the LED will display the selected Battery Type for 2 seconds. FeAtuReS Red and Green LEDs are used to display selected Battery Type: Red LED Flashing = LiPo is selected Green LED Flashing = NiMH is selected To change from one battery type to another (colors described...
  • Page 8: Chassis Tuning

    The Mini SCT has several adjustments available to you for To track test, turn the Mini SCT on and place it on the tuning the performance for your needs. Although there are ground. As you push it backwards allowing it to roll freely, multiple shock positions and camber link locations provided, punch the throttle.
  • Page 9: Ride Height

    Ride Height This is the height the chassis sits and runs at. Spring spacers included with the Mini SCT, when installed between the shock top and spring, will increase the pre-load on the spring and raise the chassis. You may want to try this when running on extremely rough surfaces.
  • Page 10: Changing The Pinion Gear/Gear Ratio

    This would be good for short layouts or when running hotter motors. The pinion on the Mini SCT offers the best balance of both. To change the pinion, remove the gear cover, loosen the motor screws, and 1.
  • Page 11: Warranty And Repair Policy

    Steering Servo Installation/Removal (c) Purchaser Remedy- Horizon’s sole obligation hereunder shall be that Horizon will, at its option, (i) repair or (ii) replace, Unplug the servo lead from the receiver. Remove the four any Product determined by Horizon to be defective. In small screws located on the bottom of the chassis that the event of a defect, these are the Purchaser’s exclusive secure the servo to the chassis.
  • Page 12 Rebuilding/Refilling the Shocks Step 5 Step 1 If you plan on completely changing the shock fluid After removing the shock, (suggested), dump out the push up on the lower spring old fluid from the shock body. cup and remove it from the Carefully fill the shock body shaft.
  • Page 13 (LOSB9826) or 3-cell 11.1 volt LiPo battery pack (LOSB9827). Please consult the Motor/Battery Chart above for suggested motor/battery combos. The use of higher voltage battery packs will cause ESC damage and void any warranty. Consult your local hobby dealer or check www.losi.com.

Table of Contents