1. Manuals
  2. Brands
  3. Redpine Signals Manuals
  4. Motherboard
  5. RS9110-N-11-02
  6. User manual

Redpine Signals RS9110-N-11-02 User Manual

Hide thumbs Also See for RS9110-N-11-02:
Table of Contents

Advertisement

Quick Links

Download this manual
RS9110-N-11-02 Evaluation Board
User Guide
V
e
r
s
i
o
n
1
.
5
V
e
r
s
i
o
n
1
.
5
February 14 2012
Redpine Signals, Inc.
2107 N. First Street, #680
San Jose, CA 95131.
Tel: (408) 748-3385
Fax: (408) 705-2019
Email:
info@redpinesignals.com
Website:
www.redpinesignals.com
Redpine Signals, Inc. Proprietary and Confidential

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RS9110-N-11-02 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Redpine Signals RS9110-N-11-02

Summary of Contents for Redpine Signals RS9110-N-11-02

  • Page 1 RS9110-N-11-02 Evaluation Board User Guide February 14 2012 Redpine Signals, Inc. 2107 N. First Street, #680 San Jose, CA 95131. Tel: (408) 748-3385 Fax: (408) 705-2019 Email: info@redpinesignals.com Website: www.redpinesignals.com Redpine Signals, Inc. Proprietary and Confidential...
  • Page 2 This document may be changed at any time at Redpine’s sole discretion without any prior notice to anyone. Redpine is not committed to updating these documents in the future. Copyright 2012 Redpine Signals Inc. All rights reserved. Redpine Signals, Inc. Proprietary and confidential Page 2...

  • Page 3: Table Of Contents

    2.6: Evaluation Software – Windows CE ........10 2.7: Evaluation Process on Linux..........11 3: Connector Details ............... 12 3.1: SPI/SDIO connector ............12 3.2: GPIO Interface Header Details ..........12 3.3: SD Memory Interface ............13 Redpine Signals, Inc. Proprietary and confidential Page 3...
  • Page 4 Figure 1: RS9110-N-11-02 Evaluation Board Block Diagram ......5 Figure 2: RS9110-N-11-02 Evaluation Board and Connectors....... 6 Figure 3: RF Cable Connected to the RS9110-N-11-02 Evaluation Board..7 Figure 4: Test Setup for Throughput Measurement ........8 Redpine Signals, Inc. Proprietary and confidential...

  • Page 5: 1: Introduction

    WLAN module to the Vector Signal Generator (VSG) and Vector Signal Analyzer (VSA) through a microwave coaxial connector switch. The RS9110-N-11-02 evaluation board facilitates you in carrying out following tests. Evaluation of the end–to-end throughput performance.

  • Page 6: Figure 2: Rs9110-N-11-02 Evaluation Board And Connectors

    Figure 2: RS9110-N-11-02 Evaluation Board and Connectors A probe point (Jumper PB9) is provided in order to measure the total power consumed by the RS9110-N-11-02 WLAN Module during transmit, receive, and standby modes. On board resistors are provided for the Mode Select, which helps the user to switch from the SDIO host interface to SPI host interface.

  • Page 7: Figure 3: Rf Cable Connected To The Rs9110-N-11-02 Evaluation Board

    RS9110-N-11-02 Evaluation Board User Guide Version 1.5 Figure 3: RF Cable Connected to the RS9110-N-11-02 Evaluation Board 1.1: LED Functionality The LED on the EVB provides a visual indication of association and on air traffic to the user. If a user connects an external power amplifier in the rsi_config_vals structure in the driver, the LED will not function as described in this section.

  • Page 8: 2: Wi-Fi Data Transfer Tests

    2: Wi-Fi Data Transfer Tests The evaluation kit allows you to carry out WLAN data transfer tests, where in RS9110-N-11-02 EVB can be connected to any 802.11bgn Access Points and user can run any network applications to verify the WLAN connection. You can also evaluate the application level throughputs using this EVB.

  • Page 9: Evaluation Software - Windows Xp

    2.3: Evaluation Process on Windows XP You can start the evaluation process as follows: Step 1: - Follow the instructions mentioned in the LiteFi_Driver_Installation_Guide_WindowsXP.pdf. Step 2: - Follow the instructions mentioned in the LiteFi_WLAN_Test_Procedure_WindowsXP.pdf. Redpine Signals, Inc. Proprietary and confidential Page 9...

  • Page 10: Evaluation Software - Linux

    The following table provides the description of the software package and installation guides to be used for carrying out the WLAN data transfer tests using an Access Point, on a Windows CE platform. Redpine Signals, Inc. Proprietary and confidential Page 10...

  • Page 11: Evaluation Process On Linux

    2.7: Evaluation Process on CE You can start the evaluation process as follows: Step 1: - Follow the instructions mentioned in the LiteFi_Driver_Installation_Guide_WindowsCE.pdf Step 2: - Follow the instructions mentioned in the RS9110_N_11_02_WLAN_Test_Procedure_WindowsCE.pdf Redpine Signals, Inc. Proprietary and confidential Page 11...

  • Page 12: 3: Connector Details

    S. No Signal Names Connector Pin No. Supply J8.1&2 BT-Active J8.3 Uart_out1 J8.4 BT_Future0 J8.5 Uart_in1 J8.6 WLAN_Active J8.7 Uart_out2 J8.8 BT_ Priority J8.9 I2C_SDA J8.10 BT_ Future1 J8.11 I2C_SCL J8.12 Uart_rts J8.13 Redpine Signals, Inc. Proprietary and confidential Page 12...

  • Page 13: Sd Memory Interface

    Signal Names Connector Pin No. RF_LDO_en J8.14 Uart_cts J8.15 Xtal_ip_en J8.16 Power_gate_en J8.18 J8.17,19&20 3.3: SD Memory Interface S.No. Signal Names Connector Pin No. J9.1 J9.2 Supply J9.3 SCLK J9.4 J9.5 J9.6 J9.6 Redpine Signals, Inc. Proprietary and confidential Page 13...

Table of Contents