Changing The Main Unit And Remote Control Mode - Panasonic SC-VKX80 Operating Instructions Manual

"AUDIO" menu
CURRENT SETTINGS
PCM OUTPUT
Do a check on the digital input
limitations of the equipment you
connect using COAXIAL terminal
and select the maximum sampling
frequency of PCM digital output.
DOLBY DIGITAL
With COAXIAL connection ( Z 19)
DTS
With COAXIAL connection ( Z 19)
MPEG
With COAXIAL connection ( Z 19)
DYNAMIC RANGE
"DISPLAY" menu
CURRENT SETTINGS
LANGUAGE
Select the language for the on-screen
messages.
"OTHERS" menu
CURRENT SETTINGS
REGISTRATION
Show the registration code of the
system.
DEREGISTRATION
Show the deregistration code of the
system.
SLIDE SHOW TIME
EASY SETUP
DVD-VR/DATA
Select to play only DVD-VR or DATA
format.
SCREEN DIMMER
This is to prevent burnt mark on the
TV screen.
DEFAULTS
This returns all values in the SETUP
menus to the default settings.

Changing the main unit and remote control mode

You can change the remote control and main unit mode if the remote
control operates other Panasonic equipment.
Make sure that the main unit and remote control have the same
mode.
To set the mode to "REMOTE 2"
1
Press and hold [EXT-IN] on the main unit and [2] on the
remote control until "REMOTE 2" is shown.
2
Press and hold [OK] and press [2] for a minimum of
2 seconds.
VKX80_GC_1En.indd 21 VKX80_GC_1En.indd 21
Show the current setting of the items in this menu.
UP TO 48kHz: When you connect to an equipment compatible with 44.1 kHz or 48 kHz.
UP TO 96kHz: When you connect to an equipment compatible with 88.2 kHz or 96 kHz.
• Signals from copy-protected discs are converted to 48 kHz or 44.1 kHz.
• Some equipment cannot support sampling frequencies of 88.2 kHz, even if they can support
96 kHz.
Read the operating instructions of your equipment for details.
BITSTREAM
PCM
Select "BITSTREAM" when the equipment can decode the bitstream (digital form of
BITSTREAM multi-channel data). If not, select "PCM". (If the bitstream output to the equipment
PCM without a decoder, there can be high levels of noise output that can do damage to
your speakers and hearing.)
BITSTREAM
PCM
ON: Adjust for clarity even when the volume is low. The range between the lowest and the highest
sound levels is compressed. Convenient for late night viewing. (Only works with Dolby Digital.)
OFF
Show the current setting of the items in this menu.
ENGLISH FRANÇAIS
PУCCKИЙ MAGYAR
Show the current setting of the items in this menu.
SHOW CODE: You must have this registration code to purchase and play DivX Video-on-Demand
(VOD) content ( Z 23, "About DivX").
This item is only shown until you play a DivX VOD content or after you deregister this system.
SET: You must have this deregistration code to cancel the registration of this system
( Z 23, "About DivX").
This item is only shown after you play a DivX VOD content for the first time.
To change the slideshow time
1 SEC to 15 SEC 15 SEC to 60 SEC
(in 1-unit) (in 5-unit)
• "3 SEC" is the factory preset.
SET: Shows the EASY SETUP settings.
DVD-VR: To play video on DVD-R/RW.
DATA: To play data files on DVD-R/RW.
OFF
WAIT 5 MIN: If there is no operation for 5 minutes, the picture becomes grey. The TV screen will
go back to the normal position when you do some operations. (This does not apply
during video playback.)
RESET
The password screen is shown if "RATINGS" ( Z 20) is set. Input the same password and press [OK],
then switch off the system and switch on again.
To set the mode to "REMOTE 1"
1
2
Note:
After you set the mode, you can continue to use the TV operation
buttons on the remote control to operate a Panasonic TV ( Z 8).
ESPAÑOL
ČESKY
60 SEC to 180 SEC
(in 30-unit)
Press and hold [EXT-IN] on the main unit and [1] on the
remote control until "REMOTE 1" is shown.
Press and hold [OK] and press [1] for a minimum of
2 seconds.
DEUTSCH
POLSKI
21
21
9/22/2010 2:34:46 PM 9/22/2010 2:34:46 PM