Advertisement
Available languages
Available languages
ASSEMBLY/ADJUSTMENT SET-UP
nstalling Blades
BEFORE INSTALLING BLADES, TURN OFF AND UNPLUG TOOL.
Your jig saw uses the Quick Clamp™ blade changing system. To install a blade, lift the Quick Clamp™
lever (Figure 1). Insert the saw blade shank fully into the blade clamp. Release the lever and the blade will
be clamped securely in place. The back of the blade should be almost touching the roller support guide.
Ensure the blade teeth are facing forward.
Roller Support Guide
The roller support guide on your jig saw improves its performance when cutting tough materials by adding
support to the blade. Adjust the support roller by loosening the screw on the bottom of the shoe, as shown
in Figure 2 and moving the roller so that it almost, but not quite, touches the blade. Tighten the screw
securely to lock the roller in place.
Switch
Your jig saw has a variable speed switch. To turn the saw on, squeeze the trigger switch, as shown in
Figure 3. Hold the trigger switch in as you rotate the speed wheel to the desired setting.
The selected speed will be maintained, under reasonable loading, as you cut.
NOTE: The numbers on the speed wheel are for reference only. They do not represent any particular speed.
To turn the tool off, release the trigger switch.
The tool can be locked on for continuous operation at any speed by squeezing and holding the trigger
switch while you depress the lock-on button. With the lock-on button depressed, release the trigger switch
and the tool will continue to run. To release from lock position, squeeze and release the trigger switch once.
Although your saw will maintain speed and power, don't overload it as this could damage the motor. Use
your saw only for its intended purpose. If it should overheat, turn it on at its highest speed and run it
without a load until it cools down.
MATERIAL
Soft Wood
Hard Wood
Plastic
Aluminum
Steel
Tile
Glass
Leather
Rubber
NOTE: Speed setting 1 is the slowest and MAX is the fastest.
Bevel Adjustment
TURN OFF AND UNPLUG TOOL.
Raise or remove the dust shield before bevel cutting.
To adjust the bevel angle, loosen the rear screw on the bottom of the shoe, as shown in Figure 4. Pull the
show backward slightly and set the shoe to the desired angle. Angle adjustment is indicated on the raised
portion of either side of the shoe (Figure 5). It is also possible to push the shoe forward to set fixed positions
of 0°, 15°, 30° or 45°. A protractor is recommended when very accurate cuts are required.
To reset the shoe for a square cut, loosen the rear screw and move the shoe until it is approximately 90° to
the blade. While applying slight forward pressure to the shoe, retighten the rear screw.
General Cutting
Be sure board is firmly secured. Hold jig saw by the handle and operate switch to turn the unit on. Don't
attempt to turn on the unit when blade is against material to be cut. This could stall the motor. Place front of
shoe on material to be cut and hold jig saw shoe down firmly against the work surface while cutting. Don't
force the tool; let the blade cut at its own speed. Whenever possible, clamp or support work close to the
line of cut; when the cut is completed, shut off power and lay the saw aside before loosening the work.
Scrolling
Your jig saw is equipped with a manual scrolling feature which permits the saw blade to completely rotate
without rotating the entire saw.
NOTE: Before scrolling, retract the roller support guide and ensure the shoe is in the forward position.
Push the scroller release button, as shown in Figure 6. The scrolling knob will pop out of the tool housing.
PULL THE KNOB UP. Using one hand to guide the jig saw, turn the scroller knob to guide the blade along
the line of the cut. The blade will turn 360°.
The angle of the blade can be locked into one of four positions: 0°, 90°, 180° or 270°. To lock the blade
in any of the four positions, push the scroller release button, and push the scrolling knob down. When the
button is released, the blade is locked into position.
To reset, push the scroller release button. To return to straight-line (non-scrolling) cutting, press the scroller
release button and push the knob down. Readjust the roller support guide so it is almost touching the back
of the blade.
Dust Shield
Your jig saw is equipped with a dust shield to aid with dust removal. Place the shield in the down position
when extracting dust.
NOTE: To clean dust shield, first unplug saw from power supply. Use only a dry rag or rag dampened with
plain water to wipe clean. When bevel cutting always keep the dust shield in the UP position.
Dust Extraction/Vacuum Attachment
Your jig saw is equipped with a dust extraction system which greatly reduces clean up time. To extract dust:
Insert the end of the supplied vacuum adapter into the dust extraction opening at the rear of the saw.
Attach a standard vacuum cleaner hose.
Turn the dust blower switch (Figure 7) to the right. Lower the dust shield.
Turn on the vacuum. Turn on the jig saw and begin cutting.
SPEED
TEETH
SETTING
PER INCH
6-MAX
7
5-MAX
7
4-6
14
3-6
14
2-4
24
1-3
24
1-3
32
4-6
0 (Knife Edge)
4-6
0 (Knife Edge)
Accessories
Recommended accessories for use with your tool are availa
center. If you need assistance regarding accessories, please
WARNING: The use of any accessory not recommen
SERVICE INFORMATION
Black & Decker offers a full network of company-owned an
America. All Black & Decker Service Centers are staffed w
efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine fac
Decker location nearest you. To find your local service loca
"Tools—Electric" or call: 1-800-54-HOW TO.
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two ye
workmanship. The defective product will be replaced or re
The first, which will result in exchanges only, is to return the
purchased (provided that the store is a participating retaile
period of the retailer's policy for exchanges (usually 30 to 9
be required. Please check with the retailer for their specific
the time set for exchanges.
The second option is to take or send the product (prepaid)
Service Center for repair or replacement at our option. Pro
owned and authorized Service Centers are listed under "To
directory.
This warranty does not apply to accessories. This warranty
have other rights which vary from state to state. Should you
your nearest Black & Decker Service Center.
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
GUIDE D'UTI
Q 4 2 5
AVANT DE RETOURNER LE P
LA RAISON, PRIÉRE D
1 800 544
RENSEIGNEMENTS
•On ne peut pas mettre la scie en m
régulateur de vitesse seulement; il fa
•Bien serrer le rouleau porteur avant
•Soulever complètement le bouton d
tourner.
FRANÇ
Advertisement
