Husqvarna 123HD65X Operator's Manual
Hide thumbs Also See for 123HD65X:

Advertisement

Quick Links

Operator´s manual
123HD60
123HD65X
Please read these instructions carefully and make sure
English
you understand them before using the machine.

Advertisement

Table of Contents
loading

Summary of Contents for Husqvarna 123HD65X

  • Page 1 Operator´s manual 123HD60 123HD65X Please read these instructions carefully and make sure English you understand them before using the machine.
  • Page 2: Key To Symbols

    KEY TO SYMBOLS Symbols Switch off the engine by moving the stop switch to the STOP position before carrying WARNING! Incorrect or careless use of out any checks or maintenance. a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury.
  • Page 3: Table Of Contents

    CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Please read the operator’s manual carefully. Symbols ............... CONTENTS WARNING! Long-term exposure to noise can Contents ..............result in permanent hearing impairment. So Note the following before starting: ........ always use approved hearing protection. INTRODUCTION Dear Customer, ............
  • Page 4: Introduction

    Dear Customer, Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.
  • Page 5: What Is What

    WHAT IS WHAT? What is what? 1 Operator′s manual 13 Lock for handle (123HD65) 2 Handle 14 Throttle control 3 Throttle lock 15 Spark plug cap and spark plug 4 Fuel cap 16 Cylinder cover 5 Choke control 17 Starter handle 6 Front handle 18 Stop switch 7 Blade guard...
  • Page 6: General Safety Precautions

    GENERAL SAFETY PRECAUTIONS Important WARNING! Listen out for warning signals or shouts when you are wearing hearing protection. Always remove your hearing IMPORTANT! protection as soon as the engine stops. The machine is only designed for cutting branches and HEARING PROTECTION twigs.
  • Page 7: Machine's Safety Equipment

    GENERAL SAFETY PRECAUTIONS Machine′s safety equipment Press the throttle lockout and make sure it returns to its original position when you release it. This section describes the machine′s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly.
  • Page 8 GENERAL SAFETY PRECAUTIONS Vibration damping system Never use a machine that has a faulty muffler. Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier. The machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and Regularly check that the muffler is securely attached to the the machine′s handle unit.
  • Page 9 GENERAL SAFETY PRECAUTIONS Blades To ensure good cutting results it is important that the contact pressure between the blades is correct. The contact pressure is adjusted by turning the screws on the underside of the bar clockwise as far as they will go. Then turn the screws anticlockwise a 1/4 turn.
  • Page 10: Fuel Handling

    • The transport guard must always be fitted to the cutting • For best results and performance use HUSQVARNA two- attachment when the machine is being transported or in stroke engine oil, which is specially formulated for our air- storage.
  • Page 11: Fuelling

    FUEL HANDLING Mixing Fuelling • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture.
  • Page 12: Starting And Stopping

    STARTING AND STOPPING Check before starting Choke: Set the choke control in the choke position. • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. Warm engine •...
  • Page 13: Working Techniques

    WORKING TECHNIQUES General working instructions Safety instructions while working IMPORTANT! This section takes up the basic safety precautions for • Always ensure you have a safe and stable working working with a hedge trimmer. position. If you encounter a situation where you are uncertain how to •...
  • Page 14: Basic Working Techniques

    WORKING TECHNIQUES Safety instructions after completing work 123HD65 • The hedge trimmer’s rear handle can be set in three positions by pulling out the catch. See figure. When the handle is adjusted the hedge trimmer should be idling or not running. •...
  • Page 15: Maintenance

    MAINTENANCE Carburettor Muffler Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak CAUTION! Some mufflers are fitted with a catalytic...
  • Page 16: Cooling System

    If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The any further action. If the spark plug is dirty, clean it and check filter oil contains a solvent to make it spread evenly through...
  • Page 17: Gear

    There is a grease nipple and a plug for filling lubricant on the gear housing. Use a grease gun to fill with grease. This should be done after every 60 working hours. Use Husqvarna’s special grease. CAUTION! The gear housing must not be filled completely with grease.
  • Page 18: Maintenance Schedule

    MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by an authorized service workshop.
  • Page 19: Technical Data

    TECHNICAL DATA Technical data Technical data 123HD60 123HD65X Engine Cylinder displacement, cm 22,5 22,5 Cylinder bore, mm 32,0 32,0 Stroke, mm 28,0 28,0 Idle speed, rpm 3000 3000 Recommended max. speed, rpm 12000 12000 Max. engine output, acc. to ISO 8893, kW/ rpm...
  • Page 20: Ec-Declaration Of Conformity

    Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Husqvarna 123HD60 and 123HD65X from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:...
  • Page 24 Original instructions 1153197-26 ´®z+U3h¶6n¨ ´®z+U3h¶6n¨ 2009-11-20...

This manual is also suitable for:

123hd60

Table of Contents