Audio Dubbing A Pre-Recorded Cassette; Using The Tv Buttons On The Remote Control - Samsung CHT-350 Instruction Manual

VCR

Audio Dubbing a Pre-recorded Cassette

GB
With the Audio Dubbing function, you erase the previously
recorded sound and replace it with a new soundtrack from:
Restriction:
Audio dubbing is applicable only to the longitudinal audio track
(normal audio).
1
2
2
2
3
4
5
6
7
7
8
9
A.DUB
-0:05:23
10
42
A CD, DVD
A microphone connected to a sound system
A cassette player
Connect an RCA audio cable to the appropriate output on your
sound system (cassette player for example).
Connect the other end of the RCA audio cable to the audio input
connectors (L, R) on the Rear of your DVD-VCR. (LINE IN 3 Only)
Insert the pre-recorded cassette on which the audio track is to be
❿
replaced, and press the ll to start playback.
➛ ➛
Search for the Audio Dubbing (ending) point using the or
and set the counter to 0:00:00 by pressing CLEAR.
Search back slightly beyond the Audio Dub start point using the
button.
❿
Press the ll button.
❿
Press the ll button one more time to make STILL mode.
Press A.DUB.
Result: Your VCR is now in the Audio dubbing Pause
mode.
On the sound system, locate the point on the cassette at which
you wish to start playback.
Example: The track that you wish to record on the cassette.
When you are ready:
Start playback on the sound system
Press the REC on the remote control.
Result: The soundtrack is replaced on the pre-recorded cassette.
The audio dubbing will finish when the counter reaches 0:00:00.
The new sound will be recorded on the normal sound
track of the tape, and the original sound will remain on
the Hi-Fi sound track.
To hear the new sound and original sound mixed
together, press the Audio button on the remote control
until the MIX option is displayed (see page 34).

Using the TV Buttons on the Remote Control

Your DVD-VCR remote control will work with Samsung televisions
and compatible brands.
To determine whether your television is compatible, follow the instructions
below.
1 Switch your television on.
2 Point the remote control towards the television.
3
Hold down the TV button and enter the two-figure code
corresponding to the brand of your television, by pressing the
appropriate numeric buttons.
Brand Codes Brand
SAMSUNG 01 to 06 PHILIPS
AKAI 09, 23 SABA
GRUNDIG 09, 17, 21 SONY
LOEWE 02 THOMSON
PANASONIC 08, 23 to 27 TOSHIBA
❿ ❿
,
Result: If your television is compatible with the remote control, it
will switch off. It is now programmed to operate with the
remote control.
➛ ➛
If several codes are indicated for your television brand, try
each one in turn until you find one that works.
When you change the batteries in the remote control, you
must reprogramme the code, following the same procedure.
You can then control the television using the following buttons.
Button Function
TV STANDBY/ON Used to switch the television on and off.
TV or VCR Used to switch the between the TV or VCR modes.
TV INPUT Used to select an external source.
+ –
TV VOL or Used to adjust the volume of the television.
PROG/TRK Used to select the required programme.
(œ or ❷)
MUTE Used to mute the volume of the television.
The various functions will not necessarily work on all
televisions. If you encounter problems, operate the
television directly.
VCR
1
2
Codes
02, 20, 22
2
13, 14, 22 to 24
15, 16
13, 14, 24
07, 16 to 19, 21
4
3
4
5
5
6
43
GB