Picture Search, Fast Forward/Rewind; Searching For A Specific Sequence; Using The Tape Counter - Samsung CHT-350 Instruction Manual

VCR

Picture Search, Fast Forward/Rewind

Picture Search enables you to Fast Forward or Rewind and look for
GB
a particular part of a tape.
1
2
3
4
5
6
VCR

Searching for a Specific Sequence

Each time you record a cassette on this VCR, an "index" is
automatically marked on the tape when recording starts.
The Search function allows you to fast-forward or rewind to a
specific index and start playback from that point. Depending on the
direction selected, the indexes are numbered as follows:
1
INTRO SCAN
1
INDEX : ➛ ➛¤¤¤¤❿ ❿
2
3
4
Index Skip Search:
This feature will enable you to fast forward/rewind to a specific
point on a tape: E.g. if you have recorded 3 different programmes
on a tape and you have rewound the tape to the beginning, by
using this feature you can go directly to the start of programme 2
simply by pressing the INDEX button.
INDEX SEARCH : ➛ ➛ - 6
1
2
3
4
38
Press PLAY, the VCR will enter normal play mode. While in play,
❿ ❿ ➛ ➛
press and release the (or ) button. The VCR will search at 5
times the normal playback speed.
❿ II
To return to normal playback mode, press the button.
❿ ❿ ➛ ➛
If you press and HOLD down the (or ) button the VCR will
❿ ❿
search at 9 times the normal speed. Releasing the button will
return the VCR to search at 5 times the normal speed. To return to
❿ II
normal playback mode, press the button.
❿ ❿
Whilst in Picture Search mode, if you press the button again,
the VCR will enter normal Fast Forward mode.
➛ ➛ ➛ ➛
Likewise, whilst in Picture Search mode, if you press the
button again, the VCR will enter normal Rewind mode.
➛ ➛ ❿ ❿
If, when Rewinding ( ) or Fast Forwarding ( ), you press the
❿ ❿
(or ) button, the VCR will enter the Picture Search mode.
Seq. being Next
Prev
played Seq.
etc. Seq. etc.
2 1 1 2
This VCR uses a standard indexing system (VISS). As a
result, it will recognize any indexes marked by other
VCRs using the same system and vice versa.
To search for a specific index, press INDEX.
➛ ➛ ❿ ❿
Press the or buttons depending on the direction where your
desired programme is located.
When an Index mark is found the VCR will playback the tape for 5
seconds, after which it will continue searching for the next Index mark.
❿ II
If you want to watch the tape from a particular Index, simply press
Press the INDEX to start the Index search.
➛ ➛ ❿ ❿
Press the or buttons twice more. This will take you directly
to the start of the desired programme is located.
❿ ❿
These Index searches can be made forwards: (press ) or
➛ ➛
backwards: (press ).
❿ II
To cancel an Index search simply press the or button.
You can set an index number up to ±20.

Using the Tape Counter

The tape counter:
Indicates the elapsed time in the play and record modes
(hours, minutes and seconds)
Is reset when a cassette is inserted in the DVD-VCR
Allows you to find the beginning of a sequence easily
If the remaining time is to be calculated correctly, you
must indicate the type of cassette being used.
1
Insert a cassette in your DVD-VCR.
2
To set the tape counter to zero at the beginning of a sequence:
➛ ➛
Press DISPLAY twice to display the counter
Press CLEAR when you want to set the tape counter to zero
3
When you are ready,
Start playback or Recording.
Press the button.
To fast-forward or rewind to the sequence at which the
➛ ➛
counter was set to zero, press
Some DVD-VCR information, such as the counter, can be
displayed on the television screen (unless you have
deactivated the OSD mode; refer to page 28).
Press DISPLAY:
Once to display the current function, programme
number, recording speed, date, time and counter
Twice to display the counter only
Three times to display the time remaining on the
cassette
Four times to clear the display
.
VCR
0:00:00
2
❿ ❿
or .
39
GB
2