Page 1
Norcent LT2722 LCD TV MONITOR THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RELIABILITY FOR CHANGES,...
Norcent LT2722 Table Of Contents Revision List .....…………....……..........…………......Table Of Contents .....................…………......1. General Specifications ................…………......2. Operating Instructions ..................……………..………….. 2.1 The Use Of Remote Control ..................…………… 2.2 Front Panel Control Knobs ..................…………… 2.3 OSD Operating ......................…………… 2.4 Safety Notice .......................…………...….
Norcent LT2722 1. General Specifications Specification Items Screen Size 27” TFT LCD color Panel (CMO) Aspect Ratio 16:9 Resolution 1280 x 720 (WXGA) Active Display Area H x V 597.12mm x 335.88mm Pixel Pitch 0.4665mm 0.4665mm Display colors 16.7 million...
Norcent LT2722 2. Operations Instructions 2.1 The Use Of Remote Control MUTE Temporarily interrupt POWER: the sound or restore it. Press to turn on/off the TV. The TV is never completely powered off unless it is physically unplugged. DISPLAY Press this button to...
Norcent LT2722 2.2 Front Panel Control Knobs Power Key: Press to turn on or off the TV. MENU Key: Press to show the OSD menu and exit OSD menu at the TV. Down / Up Key: Press to perform select function and channel.
Page 7
Norcent LT2722 PC PARAMETERS AUTO CONFIG: Enable the automatic configuration of the optimum size of the graphic. CLOCK: Adjust the time. PHASE: Adjust the phase of the graphic. POSITION: Adjust the position and angle of the graphic. AUDIO SETTINGS BASS: Adjust bass tone.
Page 8
Norcent LT2722 PICTURE-IN-PICTURE PIP POSITION: The PIP can be placed in any position on the screen according to one’s wishes. If there is no , ◄, ► buttons on the remote control to change the PIP position. menu, use the PIP SIZE: Can be used to switch the PIP off (OFF) or select the size (SMALL, MEDIUM, LARGE) of the PIP.
Page 9
Norcent LT2722 PARENTAL CONTROLS LOCK MENU: Switch the functionality to configure ratings on or off. MPAA RATING: Configure MPAA ratings. TV PG RATING: Configure TVPG ratings. PASSWORD: Change the password (default is ‘1111”). Please follow the instructions on the screen. Once changed, please remember your own password.
Page 10
Norcent LT2722 GENERAL SETTINGS OSD POSITION: Shift the position to one’s preference. OSD TIMEOUT: Configure the time to be displayed on screen. OSD LANGUAGE: Configure the language (English, French or Spanish) for the menu. OSD LOCK: Lock the selected configurations to prevent them from being overwritten.
Norcent LT2722 2.4 Safety Notice For Your Safety Before operating the TV please read this manual thoroughly. This manual should be retained for future reference FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 12
Norcent LT2722 IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth.
Page 13
Norcent LT2722 items could unsuspectingly fall from the top of the set and cause product damage and/or personal injury. Power Lines – An outdoor antenna should be located away from power lines. Outdoor Antenna Grounding – If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges.
Norcent LT2722 3. Input Specification 3.1 Input Signal connector This procedure gives you instructions for installing and using the LCD TV display. Lay the display on the desired operation and plug the power cord into a convenient AC outlet. Three-wire power cord must be shielded and is provided as a safety precaution as it connects the chassis and cabinet to the electrical conduct ground.
Norcent LT2722 4. Mechanical Instructions Step Figure Description Lay the LCD-TV Preparation on a flat, soft and clean surface. Remove Remove the hinge hinge cover as the arrowheads. cover Remove Remove the six screws base...
Page 17
Norcent LT2722 Remove Push the clip as the arrowheads cover cable Remove Remove the six screws back cover Remove Remove the six screws cover chin...
Page 18
Norcent LT2722 Remove Remove the total shield six screws Remove the four Remove scres and disconnect he main board wire harnesses...
Page 19
Norcent LT2722 Remove the six Remove screws and power disconnect the board wire harness Remove Remove the fourteen screws main frame Remove the Remove sixteen speakers screws(the left and right two and bezel speakers)
Page 20
Norcent LT2722 Remove the four Remove screws panel...
Page 21
Norcent LT2722 Remove the four screws The end...
Norcent LT2722 5. Repair Flow Chart Panel Control Circuit No Display Check CN605 pin 19-22 Replace panel or is 5V and signal on pin FPC cable to panel 3,4,6,7,9,10,12,13,15,16 NO 5V NO Signal Check U403 crystal Check Q401, Q400 X400 (14.318MHZ)
Page 23
Norcent LT2722 Main Board Power Circuit No Power Check CN606 Pin 3, 4(12V), Check Power Board circuit Pin 5, 6 (5V) Check U701 input (5V), Check Q701, Q702 and U706 input (12V) PWR_ON control relative circuit U704 Pin2 U705 Pin2...
Page 24
Norcent LT2722 Remote Control Block Remote Control can’t work Check IR Board J1 Pin 1,4(5V) and voltage at Pin 3 will change Replace D600 or IR board when received signal Check Main board 5V power Replace line between Main relative circuit and signal on...
Page 25
Norcent LT2722 PC Control Block No Display Check U403 output Check CN605, FPC relative circuit and panel cable and panel control circuit Check U403 crystal Replace X400 X400 (14.318MHZ) Check power supply for Check relative circuit 1.8V, 2.5V, and 3.3V...
Page 26
Norcent LT2722 Audio Control Block No Sound Check CN604, CN609 Replace speaker and L613, L614, L616, L617 Check U603, U604 output relative circuit and power supply 24V Check CN602 Pin3-4 and Pin1-2 are short when no Check earphone board ear-phone plug...
Norcent LT2722 6. White-Balance, Luminance adjustment Approximately 30 minutes should be allowed for warm up before proceeding white balance adjustment. Before started adjust white balance, please setting the Chroma-7120 MEM. Channel 1 to 9300 color, MEM. Channel 2 to 6500 color, and MEM. Channel 3 to 9300 color, (9300 parameter is x =283, y = 297, Y = 380cd/m2 (PC Mode);...
Page 28
Norcent LT2722 B. Adjust 6500 color-temperature: 1. Switch the chroma-7120 to RGB-mode (with press “MODE” button) 2. Switch the MEM. Channel to Channel 02 (with up or down arrow on Chroma-7120) 3. The LCD-indicator on chroma-7120 will show x = 313, y=329, Y>380.
Page 70
Norcent LT2722 +1.8V_CORE Place Series termination resistors on bidirectional lines-DATA and DQS midway between gm1601 BGA and memory Max trace length on this interfce is 2.5 inches C419 C421 C422 C423 C424 C425 C426 C427 C428 C429 C430 C431 C432...
Need help?
Do you have a question about the LT2722 and is the answer not in the manual?
Questions and answers