Setting The Camera Id; Setting The Date And Time - Panasonic AG-DVC200 Operating Instructions Manual

Preparation

Setting the camera ID

The camera ID is set on the <CAMERA ID> screen. Up to 12
alphanumerics, symbols and spaces can be used.
<Note>
The camera ID does not appear while the setting menu is displayed
even when color bar signals are output.
1
Proceed with the sub-menu operation
(page 30), and open the <CAMERA ID>
screen.
#3< C A M E R A I D >
C A M E R A I D : I D
I D : ¢¢¢¢¢¢¢¢¢¢¢¢
2
Turn the JOG dial button to move the
arrow (cursor) to the ID item.
3< C A M E R A I D >
C A M E R A I D : I D
v
# I D : ¢¢¢¢¢¢¢¢¢¢¢¢
3
When the JOG dial button is pressed, the
arrow (cursor) flashes to signal that the
input mode has been established.
4
Keep turning the JOG dial button until the
character to be set appears.
When the button is turned, the character display is switched in
the following sequence:
Space: ∏
7
Letters of the alphabet: A through Z
7
Numbers: 0 through 9
7
Symbols: ', >, <, /, -
5
Press the JOG dial button to enter the
character.
6
Turn the JOG dial button to move the
arrow (cursor) to the next position (on the
right), and repeat steps 3, 4 and 5 to enter
the remaining characters.
7
Press the MENU button to end the menu
operation.
The setting menu is cleared, and the unit's current status is
displayed.
;
To change the back to
;
the is above the colon (:).
<Note>
The camera ID input above will be recorded at the same time as the
color bar signals.
>
, press the JOG dial button when

Setting the date and time

1
Proceed with the sub-menu operation
(page 37) to open the <TIME/DATE> screen.
#3 < T I M E / D A T E >
Y E A R
M O N T H
D A Y
H O U R
M I N U T E
T I M E / D A T E S E T : R E A D Y
2
Turn the JOG dial button to select the item
to be changed, and press the JOG dial
button.
3< T I M E / D A T E >
Y E A R
M O N T H
D A Y
H O U R
#
M I N U T E
T I M E / D A T E S E T : R E A D Y
3
Turn the JOG dial button to change the
setting, and then press the button to enter it.
4
When the setting is completed, turn the
JOG dial button to select TIME/DATE SET,
and press the button.
The READY display changes from ACTIVE to OK, and the
clock function starts operating.
3< T I M E / D A T E >
Y E A R
M O N T H
D A Y
H O U R
M I N U T E
#
T I M E / D A T E S E T : O K
5
Press the MENU button to end the menu
operation.
The setting menu is cleared, and the unit's current status is
displayed.
<Note>
≥The seconds cannot be set. The time always starts from zero
seconds.
≥At normal temperature with the power off, the clock will have an
accuracy of ±30 seconds/month.
necessary, check the time with the power on and reset to the
correct time.
14
: 0 1
: 0 1
: 0 1
: 0 0
: 0 0
: 0 1
: 0 1
: 0 1
: 0 0
: 0 0
: 0 1
: 0 1
: 0 1
: 0 0
: 0 0
When accurate time is