Returning A Scene Filename To Its Default; How To Use File Select - Panasonic AG-DVC200 Operating Instructions Manual

Scene files
9
Rotate the JOG dial button to move "
the WRITE item.
3< S C E N E F I L E >
N A M E E D I T
F I L E N A M E
#
W R I T E ( U S E R ) : R E A D Y
I N I T ( U S E R ) : R E A D Y
10
When the JOG dial button is pressed, the
following message is displayed.
3< S C E N E F I L E >
N A M E E D I T
F I L E N A M E
#
W R I T E ( U S E R ) : N O
I N I T ( U S E R ) : R E A D Y
11
Rotate the JOG dial button to select YES,
and press the JOG dial button.
When the data has been written (saved), the following
message is displayed.
3< S C E N E F I L E >
N A M E E D I T
F I L E N A M E
#
W R I T E ( U S E R ) : O K
I N I T ( U S E R ) : R E A D Y
<Note>
Repeat step 11 if the NG display appears.
12
Press the MENU button to exit the menu
operation.
The setting menu is cleared, and the displays showing the
unit's current statuses appear on the viewfinder screen.
Returning a scene filename to
its default
Rotate the JOG dial button to move ">" to the INIT item, and
perform steps 10 and 11 of "Editing scene filenames" in the
previous section.
The scene filenames are returned to their defaults (factory settings).
<Note>
The scene file setting data are also returned to their default values.
>
" to
U S E R : T A R O
- - - - - - - -
U S E R : F A C T O R Y
F 1 : F L U O .
F 2 : S P A R K L N G
F 3 : C O O L
F 4 : R E T R O
S T D : F A C T O R Y
U S E R : T A R O
- - - - - - - -
U S E R : F A C T O R Y
F 1 : F L U O .
F 2 : S P A R K L N G
F 3 : C O O L
F 4 : R E T R O
S T D : F A C T O R Y
U S E R : T A R O
- - - - - - - -
U S E R : T A R O
F 1 : F L U O .
F 2 : S P A R K L N G
F 3 : C O O L
F 4 : R E T R O
S T D : F A C T O R Y

How to use file select

Up to four menu setting parameters other than scene files can be
stored in the memory. These parameters are MAIN 1/2 and MAIN
2/2 menu items. For further details, refer to "List of file settings"
(page 25).
Files are written and read on the sub-menu <DATA READ/WRITE>
screen (page 33). When the unit was shipped from the factory, the
default values (factory settings) were stored in four files.
Proceed with the menu operations (page 30) to display the sub-
menu <DATA READ/WRITE> screen.
1
Operate the JOG dial button to select 1, 2,
3 or 4 as the FILE SELECT number.
3< D A T A R E A D / W R I T E >
#
F I L E S E L E C T
F I L E R E A D ( 1 ) : R E A D Y
F I L E W R I T E ( 1 ) : R E A D Y
R E A D F A C T O R Y : R E A D Y
2
Proceed with writing setting statuses in a
file or calling them from a file.
1 To write the unit's setting statuses in the file with the
selected number when it is selected, execute FILE WRITE
( ¢) (where the number of the selected file is input into " ¢ ").
2 To call the unit's setting statuses from the file with the
selected number, execute FILE READ ( ¢) .
3 To return to the default statuses, execute READ FACTORY.
For details on this operation, refer to the scene file settings.
24
: 1