Using The Vcr2 Terminals (For Sc-Ht07); Making A Recording; The Reset Function - Panasonic SC-HT07 Operating Instructions Manual

D-INPUT (Digital input)
Change the setting for the DIGITAL IN terminals (OPT1, OPT2,
COAXIAL) on the rear of the unit if the equipment you have
connected is different to that labeled.
MULTI CONTROL
1. Press [TOP MENU].
<, >
2. Press [ ] to select "SETUP".
[ENTER]
("D-INPUT" lights.)
è
<, >
3. Press [ ] to select "CD"
"DVR" or "DVD".
[ENTER]
è
<, >
4. Press [ ] to select "NONE"
"OPT1", "OPT2" or "COAX".
[ENTER]
è
The factory settings are:
SC-HT07 SC-HT05
CD: NONE TV: OPT1
TV: OPT1 DVR: OPT2
DVR: OPT2 DVD: COAX
DVD: COAX
Note
You can allocate only one piece of equipment per terminal. So
for example if you change "TV" for "OPT1" to "OPT2", "DVR" will
automatically switch to "OPT1".
Sleep timer
The SLEEP timer can turn the unit off after a set time.
It does not control any other components.
MULTI CONTROL
1. Press [TOP MENU].
<, >
2. Press [ ] to select "SLEEP".
[ENTER]
è
<, >
3. Press [ ] to select the required time.
The display changes as follows:
OFF 30 60 90
v v v
[ENTER]
è
Remote control
Press [SLEEP].
Press [–/L] or [+/R] to select the required time.
To check the setting
Press [SLEEP] on the remote control once.
The time remaining appears.
To change a setting
Repeat the procedure from the beginning.
[ENTER]
è
, "TV",
(SC-HT07 only)
,
(SC-HT07 only)
120 (minutes)
v
Using the VCR2 terminals
(for SC-HT07)
^ SFC
WER
8 INPUT SELECTOR MUSIC AV/MOVE TUNE TUNE
VIDEO IN L AUDIO IN R VCR 2
These terminals are convenient for equipment you want to
connect only temporarily. Select "VCR2" for input.

Making a recording

INPUT SELECTOR
^ SFC
POWER 8 INPUT SELECTOR MUSIC AV/MOVE TUNE TUNE
VIDEO IN L AUDIO IN R VCR 2
Recording on other equipment
You can record to a tape deck connected to TAPE REC OUT
(SC-HT07), or a DVD recorder/VCR connected to DVR/VCR1
(DVD/VCR) OUT.
1. Press [INPUT SELECTOR] to select the source to be
recorded.
2. Begin recording.
Follow your recording unit's operating instructions.
3. Start the source to be recorded.
Note
• (SC-HT07) With a tape deck, you can record any analogue
source except TAPE.
• With a DVD recorder/VCR, you can record any analogue
source except DVR/VCR1 (DVR/VCR).
• When you select DVD 6CH INPUT mode, only sound from the
front left and right channels is recorded.
• Some sources do not allow digital recording. Connect through
the analog terminals and select "ANALOG" input.

The RESET function

The operation settings for the unit will be initialized to the
settings made at the time of shipment.
However, any preset radio stations will not be erased.
MULTI CONTROL
1. Press [TOP MENU].
<, >
2. Press [ ] to select "SETUP".
[ENTER]
è
<, >
3. Press [ ] to select "RESET".
[ENTER]
è
<, >
4. Press [ ] to select "YES".
[ENTER]
è
AUDIO OUT
VIDEO OUT
Video camera
21