Advertisement
1. KNOW YOUR TOOL
Read and understand the owners manual and labels affixed to
the tool. Learn its application and limitations as well as its
specific potential hazards.
2. GROUND THE TOOL.
This tool is equipped with an approved 3-conductor cord and
a 3-prong grounding type plug to fit the proper grounding
type receptacle. The green conductor in the cord is the
grounding wire. NEVER connect the green wire to a live
terminal.
3. KEEP GUARDS IN PLACE.
Keep in good working order, properly adjusted and aligned.
4. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make sure the
floor is clean and not slippery due to wax and sawdust
build-up.
6. AVOID DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations or expose
them to rain. Keep work area well lit and provide adequate
surrounding work space.
7. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILD-PROOF.
Use padlocks, master switches or remove starter keys.
9. USE PROPER SPEED.
A tool will do a better and safer job when operated at the
proper speed.
10. USE RIGHT TOOL.
Don't force the tool or the attachment to do a job for which it
was not designed.
11. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings,
watch) because they could get caught in moving parts. Non-
slip footwear is recommended. Wear protective hair covering
to contain long hair. Roll up long sleeves above the elbows.
SPECIFIC SAFETY RULES FOR YOUR CUT-OFF MACHINE
FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL
BEFORE OPERATING ABRASIVE CUT-OFF
1. Wear eye protection.
2. Do not expose to rain or use in damp locations.
3. Replace cracked wheel immediately.
4. Always use guards and eye shields.
5. Do not overtighten wheel lock bolt.
6. Use only flanges furnished with the cut-off.
7. Frequently clean grinding dust underneath cut-off.
8. Make sure the cut-off wheel is securely mounted as described in
the operating instructions before connecting the tool to a power
supply. Do not tighten wheel excessively, since this can cause
cracks.
GENERAL & SPECIFIC
SAFETY INSTRUCTIONS
12. ALWAYS WEAR SAFETY GLASSES.
13. DON'T OVERREACH.
14. MAINTAIN TOOL WITH CARE.
15. DISCONNECT TOOLS.
16. AVOID ACCIDENTAL STARTING.
17. USE RECOMMENDED ACCESSORIES.
18. NEVER STAND ON TOOL.
19. CHECK DAMAGED PARTS.
20. NEVER LEAVE MACHINE RUNNING
UNATTENDED.
9. Check wheel for fissures and cracks, and test for normal
operation prior to use.
10. Use only cut-off wheel rated for 4400RPM or greater and
manufactured in compliance with ANSI B 7. 1. Always store
wheels in a dry place with little temperature variation.
11. Always use the abrasive wheel against the work piece when
starting to cut. A harsh impact can break the wheel.
12. Before cutting, press the safety button then the trigger switch
and allow the cut-off wheel to reach full speed before cutting.
Always wear safety glasses (ANSI Z87.1). Everyday
eyeglasses only have impact resistant lenses, they are NOT
safety glasses. Also use a face or dust mask if cutting operation
is dusty.
Keep proper footing and balance at all times.
Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
Before servicing, when changing accessories or attachments.
Make sure the switch is in the ''OFF'' position before plugging
in.
Consult the manual for recommended accessories. Follow the
instructions that accompany the accessories. The use of
improper accessories may cause hazards.
Serious injury could occur if the tool tips over. Do not store
materials such that it is necessary to stand on the tool to reach
them.
Before further use of the tool, a guard or other parts that are
damaged should be carefully checked to ensure that they will
operate properly and perform their intended function. Check
for alignment of moving parts, breakage of parts, mounting,
and any other conditions that may affect its operation. A guard
or other parts that are damaged should be properly repaired or
replaced.
Turn power ''OFF''. Don't leave any tool running until it comes
to a complete stop.
Advertisement
