Part List - York Active 110 Owner's Manual

Part list

YORK REF. REF. DESCRIPTION
52047-1 A CONSOLE
52047-2 A-1 SCREW (M5 X 10)
52047-3 B FRONT HANDELBAR
52047-4 B-1 SCREW (M3 X 20L)
52047-5 B-2 FOAM GRIP
52047-6 B-3 HAND PULSE SENSOR
52047-7 B-4 HAND PULSE SENSOR WIRE
52047-8 B-5 SENSOR WIRE, UPPER
52047-9 B-6 HEX HEAD SCREW (M8 X P1.25 X 16L)
52047-10 B-7 SEMI-CIRCULAR WASHER (Ø8 X Ø19 X 2T)
52047-11 B-8 END CAP
52047-12 B-9 UPPER HANDLEBAR SET
52047-13 B-10 FOAM GRIP
52047-14 B-11 UPPER HANDLEBAR
52047-15 B-12 END CAP
52047-16 C-1 HANDLEBAR POST
52047-17 C-2 TENSION CONTROLLER, UPPER
52047-18 C-3 CURVED WASHER (Ø17.5 X Ø25 X 0.3T)
52047-19 C-4 FLAT WASHER (Ø10 X Ø26 X 2T)
52047-20 C-5 NYLOC SCREW (M8 X P1.0 X 20L)
52047-21 C-6 LOWER HANDLEBAR
52047-22 C-7 SPRING WASHER(Ø8.1 X Ø12.9 X 2.4T)
52047-23 C-8 SEMI-CIRCULAR WASHER
52047-24 C-9 HEX HEAD SCREW (M8 X P1.25 X 16L)
52047-25 C-10 SENSOR WIRE, LOWER
52047-26 D-R PEDAL ARM, RIGHT
52047-27 D-L PEDAL ARM, LEFT
52047-28 D-1R/L PEDAL, PAIR
52047-29 D-2 NYLON NUT (9/16" X 6T)
52047-30 D-3 C-CLIP (Ø17)
52047-31 D-4 FLAT WASHER (Ø17.5 X Ø25 X 0.3T)
52047-32 D-5 CRANK PIN, LEFT
52047-33 D-6 CRANK PIN, RIGHT
52047-34 D-7 END CAP
52047-35 D-8 NYLON NUT (9/16" X 6T)
52047-36 E FRAME
52047-37 E-1 SENSOR HOLDER
52047-38 E-2 SCREW (M4 X 10L)
52047-39 E-3 C-CLIP (Ø20)
52047-40 E-4 CURVED WASHER (Ø20 X Ø30 X 0.3T)
52047-41 E-5 FLAT WASHER (Ø20.3 X Ø30 X 1T)
52047-42 E-6 BEARING (6004RS PLASTIC)
52047-43 E-7 DRIVE PULLEY
52047-44 E-8 BUSHING (Ø20.5 X Ø25 X 7.5MM)
52047-45 E-9 AXLE
QTY. YORK REF.
1 52047-46
4 52047-47
1 52047-48
2 52047-49
2 52047-50
2 52047-51
1 52047-52
1 52047-53
3 52047-54
3 52047-55
2 52047-56
2 52047-57
2 52047-58
2 52047-59
2 52047-60
1 52047-61
1 52047-62
2 52047-63
2 52047-64
2 52047-65
2 52047-66
4 52047-67
4 52047-68
4 52047-69
1 52047-70
1 52047-71
1 52047-72
2 52047-73
1 52047-74
4 52047-75
2 52047-76
1 52047-77
1 52047-78
2 52047-79
1 52047-80
1 52047-81
1 52047-82
1 52047-83
1 52047-84
1 52047-85
1 52047-86
2 52047-87
1 52047-88
1 52047-89
1
www.yorkfitness.com
REF. DESCRIPTION
E-10 HEX SCREW (M8 X P1.25 X 12L X 5T)
E-11 DRIVE BELT
E-12 CRANK, RIGHT
E-13 PATTERN NUT (M10 X P1.25 X 10T)
E-14 SIDE COVER, RIGHT
E-15 SCREW (3/16" X 3/4")
E-16 SIDE COVER, LEFT
E-17 SCREW (M4 X 50L)
E-18 CRANK, LEFT
E-19 TENSION CONTROLLER, LOWER
E-20 SPEED SENSOR
F HARDWARE PACK (F-1~F-11)
F-1 SEMI-CIRCULAR WASHER (Ø8 X Ø19 X 2T)
F-2 ACRON NUT (M8)
F-3 CARRIAGE BOLT (M8 X P1.25 X 35L)
F-4 SCREW COVER
F-5 HEX HEAD SCREW (M6 X P1.0 X 40L)
F-6 FLAT WASHER (Ø6 X Ø16 X 2T)
F-7 LOCKING KNOB
F-8 SPRING WASHER (Ø6)
F-9 FLAT WASHER (Ø8 X Ø16 X 1T)
F-10 HEX HEAD SCREW (M8 X P1.25 X 45L)
F-11 CARRIAGE BOLT (M8 X P1.25 X 75L)
G MAGNET BRACKET (G-1~G-6)
G-1 HEX SCREW (M6 X P1.0 X 16L)
G-2 SPRING WASHER (Ø6)
G-3 FLAT WASHER (Ø6 X Ø13 X 1T)
G-4 C-CLIP (Ø12)
G-5 CURVED WASHER (Ø12.5 X Ø18 X 0.3T)
G-6 SPRING (Ø12 X Ø1.4 X 9T)
H FLYWHEEL SET
H-1 NUT (3/8" X -26 X 4.5T)
H-2 PATTERN NUT (3/8" X -26 X 7T)
H-3 FLYWHEEL AXLE
H-4 FLAT WASHER (Ø10 X Ø14 X 1T)
H-5 BEARING (6000RS PLASTIC)
H-6 BEARING (6300RS PLASTIC)
H-8 BUSHING (Ø10 X Ø14 X 6MM)
I-1 REAR STABILIZER END CAP
I-2 REAR STABILIZER
J-1 END CAP W/ TRANSPORT WHEEL
J-2 SCREW (M3 X 8)
J-3 FRONT STABILIZER
FIXING BLISTER PACK
QTY.
3
1
1
2
1
6
1
5
1
1
1
1
8
10
4
2
6
6
6
6
2
2
4
1
2
2
2
2
2
1
1
3
2
1
1
1
1
1
2
2
2
2
1
1
17