Download Print this page

Canon CLI-521BK Refilling Instructions

Black ink cartridge.
Hide thumbs
   

Advertisement

Inktec Refilling Instructions for
Canon CLI-521BK
Black Ink Cartridge
(BKI-9021D)
designed to work with genuine Canon cartridge only
2ml
Insert the cartridge into the refill clip completely. Place the
1.
sponge side of the cartridge first and then press down the opposite
until you hear it clicking into place
side
Open the cap of the ink container and connect the ink injection
2.
needle. As shown in the figure, turn the refill clip upside down
that the bottom part faces upward.
3. Insert the ink injection needle into the hole of the refill clip tank, and
inject
2ml of ink. Wait 1 to 2 minutes
into the sponge inside the cartridge, and then close the hole again
supplied rubber plug
Warning:
4.
As shown in the figure, turn the refill clip
sharp tool such as a knife, cut out the sticker attached on the top of the cartridge in
a round shape. With the supplied gimlet, take out the ball to create an ink injection
inlet.
Warning:
as a knife.
5. Slowly inject
and then completely close the ink injection inlet
plug
.
5ml
Warning:
cartridge.
Warning:
6.
Remove the cartridge from the refill clip and clean the excessive ink around the nozzle,
dabbing
the nozzle part of the cartridge on some sheets of soft tissue. Then install it in the
printer.
Note:
If the ink keeps on leaking out of the cartridge nozzles after refilling or the printout
quality is not good enough, read the "Emergency measures when problems occur after
refilling" at the end of the user manual and take the right step.
7.
Change
the printer setup
Case 1:
When the window of
- Click the
"OK"
- When the window of
Case 2: When the window of
- Click the
"yes"
- When the message of
"Stop/Reset"
Before using the printer, run the
Warning:
The level warning system of the refilled cartridge will be deactivated permanently. Refill the
cartridge only when the print quality begins to deteriorate and the cartridge is actually out of ink. If you keep
on printing without inks for a long time, the print head will be damaged.
.
If you inject too much ink, it may flow over or leak out.
Take special care not to hurt yourself when you use a sharp tool such
5ml
of ink into the ink injection inlet for about
The ink volume specified above is for a completely empty
If you inject too much or too quickly, it may flow over or leak out.
as below:
"ink is running low"
or
"out of paper"
button on your printer
"ink has run out"
appears, follow the procedures Case 2 below.
"ink has run out"
button on the window.
"Press and hold the Stop/Reset" button....
or
"out of paper"
button on your printer for 10 seconds.
"head cleaning"
INKJET
O N L I N E
.
until the ink is completely absorbed
back to upright position
with another rubber
appears:
appears:
appears, press and hold the
process.
so
with the
and with a
20 seconds
,

Advertisement

   Summary of Contents for Canon CLI-521BK

  • Page 1

    Inktec Refilling Instructions for Canon CLI-521BK Black Ink Cartridge (BKI-9021D) designed to work with genuine Canon cartridge only Insert the cartridge into the refill clip completely. Place the sponge side of the cartridge first and then press down the opposite...

  • Page 2

    Inktec Refilling Instructions for Canon CLI-521BK Black Ink Cartridge (BKI-9021D) designed to work with genuine Canon cartridge only GENERAL INFORMATION FOR SUCCESSFUL REFILLING 1. Appropriate timing and method for refilling - Please try to refill as soon as the ink is exhausted.

This manual also for:

Bki-9021d

Comments to this Manuals

Symbols: 0
Latest comments: