Page 1
Grand Caravan 2 0 1 1 O W N E R ’ S M A N U A L...
Page 2
VEHICLES SOLD IN CANADA INSTALLATION OF RADIO TRANSMITTING EQUIPMENT With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of Special design considerations are incorporated into this The antenna cable should be as short as practical and Chrysler Group LLC shall be deemed to be deleted and features and equipment that are either standard or op- vehicle’s electronic system to provide immunity to radio...
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
Page 11
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Remote Starting System — If Equipped ..28 ▫...
Page 12
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Enhanced Seat Belt Use Reminder System Sliding Side Door ..... . 43 (BeltAlert ) .
Page 13
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Rear Seat Delete Feature Safety Tips ......100 (Commercial Vehicles Only) —...
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch.
Page 15
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion.
Page 16
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Removing Key Fob From Ignition CAUTION! Place the shift lever in PARK. Turn the Key Fob to the LOCK position and then remove the Key Fob. An unlocked car is an invitation to thieves. Always remove the Key Fob from the ignition and lock all NOTE: Power window switches will also remain active doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 SENTRY KEY the bulb check, it indicates that someone used an invalid The Sentry Key Immobilizer system prevents unauthor- Key Fob to start the engine. Either of these conditions will ized vehicle operation by disabling the engine. The result in the engine being shut off after two seconds.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys NOTE: When having the Sentry Key Immobilizer system serviced, bring all vehicle Key Fobs with you to NOTE: Only Key Fobs that are programmed to the the authorized dealer. vehicle electronics can be used to start and operate the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 VEHICLE SECURITY ALARM — IF EQUIPPED present, the Vehicle Security Alarm will ignore that The Vehicle Security Alarm monitors the vehicle doors condition and monitor the remaining doors and ignition. for unauthorized entry and the ignition switch for unau- To Arm The System thorized operation.
Page 20
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm The System Vehicle Security Alarm will arm regardless of whether Either press the UNLOCK button on the RKE transmitter you are in the vehicle or not. If you remain in the vehicle or insert a valid ignition key into the ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 ILLUMINATED ENTRY — IF EQUIPPED REMOTE KEYLESS ENTRY (RKE) — The courtesy lights will turn on when you use the IF EQUIPPED Remote Keyless Entry (RKE) transmitter to unlock the This system allows you to lock or unlock the doors and doors (this feature is only available if you have RKE) or liftgate, and activate the Panic Alarm, optional power if you open a door.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE equipped from the factory with three-button RKE trans- Seven-button RKE transmitters will provide functions mitters, and those built with power options will be that allow the same basic operation as the three-button, equipped with up to seven-button RKE transmitters.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • For vehicles not equipped with the EVIC, the Remote Remote Unlock Doors And Liftgate Press and release the UNLOCK button on the RKE Unlock feature can be enabled or disabled by perform- transmitter once to unlock the driver’s side or twice to ing the following steps: unlock all doors and liftgate.
Page 24
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the RKE transmit- Sound Horn with Remote Lock ter while you are inside the vehicle will activate the This feature will cause the horn to chirp when the doors Vehicle Security Alarm.
Page 25
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 2. Press the LOCK button on a programmed RKE trans- Using The Panic Alarm mitter for at least 4 seconds, but no longer than 10 sec- To turn the Panic Alarm feature on or off, press and hold onds.
Page 26
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Open/Close Power Liftgate — If Equipped Power Open/Close Left Power Sliding Door — Press the LIFTGATE button twice on the RKE transmitter If Equipped within five seconds to Open/Close the Power Liftgate. If Press the LEFT Power Sliding Door button twice on the the button is pushed while the liftgate is being power RKE transmitter within five seconds to Power Open/...
Page 27
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 • For vehicles not equipped with the EVIC, perform the RKE transmitter is pushed while the door is being power-closed, the door will reverse to the full open following steps: position. 1. Perform this operation while standing outside the If the vehicle is locked and the Vehicle Security Alarm is vehicle.
Page 28
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the RKE transmit- 1. Remove the emergency key by sliding the mechanical ter while you are in the vehicle will activate the Vehicle latch at the top of the RKE transmitter sideways with Security Alarm.
Page 29
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. To assemble the RKE transmitter case, snap the two REMOTE STARTING SYSTEM — IF EQUIPPED halves together. This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conve- General Information niently from outside the vehicle while still This device complies with Part 15 of the FCC rules and...
Page 31
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • Brake switch inactive (brake pedal not pressed) WARNING! (Continued) • Ignition key removed from ignition switch • Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start •...
Page 32
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For security, power window and power sunroof op- The EVIC message stays active until the ignition is turned to the ON/RUN position. eration (if equipped) are disabled when the vehicle is in the Remote Start mode.
Page 33
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 To Exit Remote Start Mode And Drive The Vehicle Cancel Remote Start Before the end of the 15-minute cycle, press and release Remote Starting will also cancel if any of the following the UNLOCK button on the RKE transmitter to unlock occur: the doors and disarm the Vehicle Security Alarm (if...
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Turn Off The Engine While In Remote Start DOOR LOCKS Mode Manual Door Locks Press and release the REMOTE START button one time or Lock the front doors by pushing down on the lock knobs allow the engine to run for the entire 15 minute cycle.
Page 35
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 If the lock knob is rearward when you shut either side WARNING! sliding door, the door will lock. Make sure the keys are • For personal security and safety in the event of an not inside the vehicle before closing the door.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks — If Equipped The doors can also be locked and unlocked with the A power door lock switch is on each front door trim Keyless Enter-N-Go (Passive Entry) system. For further panel.
Page 37
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Lock Doors Automatically — If Equipped If the Lock Doors Automatically feature is enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The Lock Doors Automatically feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: •...
Page 38
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Fasten your seat belt. (Fastening the seat belt will The Lock Doors Automatically at 15 mph (24 km/h) cancel any chiming that may confuse you during this feature can be reactivated by repeating the above men- programming procedure.) tioned procedure or by performing the procedure in the EVIC (if equipped), Personal Settings (Customer-Pro-...
Page 39
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 • On vehicles equipped with the optional Electronic 5. Within 30 seconds, press the driver’s door lock switch Vehicle Information Center (EVIC), refer to “Electronic in the UNLOCK direction. Vehicle Information Center (EVIC)/Personal Settings 6.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows You can control either the front or rear windows using Power Vent Windows — If Equipped switches located on the driver’s door trim panel. The The Power Vent Window Switch located on the driver’s switches will operate only when the ignition switch is in door trim panel allows the driver to operate the two vent the ON/RUN or ACC position and during power acces-...
Page 41
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 NOTE: Power Window switches will also remain active for up to 10 minutes after the ignition switch has been turned to LOCK, depending upon the accessory delay setting. Opening a front door will cancel this feature. Power Window Lockout Switch —...
Page 42
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Passenger Power Window Switch There is a single switch on the front passenger’s door trim panel which operates the passenger door window and locks and unlocks all doors. The switch will operate only when the ignition switch is in the ON/RUN or ACC position and during power accessory delay.
Page 43
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Sliding Side Door Power Window Switch — If Equipped Second row passengers may open and close the sliding door window by a single switch on the door handle assembly. The switches will operate only when the ignition switch is in the ON/RUN or ACC position and during power accessory delay.
Page 44
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto-Down Feature — If Equipped To stop the window from going all the way up during the The front window switches may be equipped with an Auto Up operation, push down on the switch briefly. Auto-Down feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Wind Buffeting WARNING! Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the There is no anti-pinch protection when the window ears. Your vehicle may exhibit wind buffeting with the is almost closed.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To keep your door operating properly, observe the fol- NOTE: The left side sliding door cannot be opened lowing guidelines: while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the •...
Page 47
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Press the button on the RKE transmitter twice within five seconds to open a power sliding door. When the door is fully open, pressing the button twice within five seconds a second time will close the door. There are power sliding side door switches located on the b-pillar trim panel, just in front of the power sliding door for the rear seat passengers and in the overhead console...
Page 48
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the power sliding side door is not in the full open or To avoid unintentional operation of the power sliding doors from the rear seats, press the power sliding door close position, it will fully open when a power sliding master lock button, located in the overhead console, to door switch is pressed.
Page 49
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Power Sliding Side Door Open Flash 4. A single chime will sound to signify that you have The left and right exterior hazard lights will flash for successfully completed the programming. 12 seconds when either sliding door is opened. This will You can turn the feature back on by repeating the alert other drivers in the area that passenger(s) could be previous procedure.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the power sliding door master lock switch is in the Sliding Side Door Child Protection Lock ON position, the power sliding side door may not be To provide a safer environment for small children riding opened or closed by pressing the switch located on the in the rear seats, the sliding doors are equipped with a b-pillar trim panel, just in front of the sliding door or...
Page 51
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 • When the Child Protection Door Lock system is en- gaged, (even if the inside door lock is in the unlocked position) the door can be opened only by using the outside door handle, the RKE transmitter, the switches on the overhead console or the switches located on the trim panel just in front of the power sliding door.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: WARNING! • After setting the Child Protection Door Lock system, always test the door from the inside to make certain it Avoid trapping anyone in the vehicle in a collision. is in the desired position. Remember that the sliding doors can only be opened from the outside door handle or the switches located •...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 To open the liftgate, press the liftgate release handle If the liftgate is locked and is not equipped with the located on the underside of the license plate bar and pull power liftgate feature, pressing the button on the RKE the liftgate open with one fluid motion.
Page 54
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may also be opened and closed by The power liftgate may be closed by pressing the button, pressing the button located on the overhead console. located in the upper left trim in the liftgate opening. Pushing once will only close the liftgate.
Page 55
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 • During power operation, whether liftgate is fully open When the RKE transmitter button is pressed and the Flash Lights feature is enabled, the tail lights will flash to or fully closed, the liftgate chime will beep several signal that the liftgate is opening or closing.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the power liftgate encounters multiple obstructions OCCUPANT RESTRAINTS within the same cycle, the system will automatically Some of the most important safety features in your stop and must be opened or closed manually. vehicle are the restraint systems: •...
Page 57
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 • An energy-absorbing steering column and steering Please pay close attention to the information in this wheel section. It tells you how to use your restraint system properly, to keep you and your passengers as safe as •...
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and they WARNING! can reduce the seriousness of injuries in an accident. • It is dangerous to ride in a cargo area, inside or Some of the worst injuries happen when people are thrown from the vehicle.
Page 59
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 2. The seat belt latch plate is near the seatback of the WARNING! (Continued) front seats and next to your arm in the rear seats. Grasp • Wearing your belt in the wrong place could make the latch plate and pull out the belt.
Page 60
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click”. • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in an accident, increasing head and neck injury.
Page 61
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
Page 62
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. WARNING! The belt will automatically retract to its stowed position. • A lap belt worn too high can increase the risk of If necessary, slide the latch plate down the webbing to allow the belt to retract fully.
Page 63
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Third Row Center Shoulder Belt Instructions downward to help position the belt away from your The shoulder belt for the third row center seat is located neck. The upper anchorage can be adjusted upward by in the headliner slightly behind the third row seat.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • ALR — Automatic Locking Retractor As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average If the passenger seating position is equipped with an you will prefer a higher position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 anytime a child safety seat is installed in a seating WARNING! position that has a belt with this feature. Children • The belt and retractor assembly must be replaced 12 years old and under should always be properly restrained in the rear seat.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners identified by any markings, only through visual inspec- The seat belts for both front seating positions are tion of the head restraint. The head restraint will be split equipped with pretensioning devices that are designed to in two halves, with the front half being soft foam and remove slack from the seat belt in the event of an trim, the back half being decorative plastic.
Page 67
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 However if during a front impact, a secondary rear CAUTION! impact occurs, the AHR may deploy based on the sever- ity and type of the impact. All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of an...
Page 68
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand Positioning Points On AHR 2.
Page 69
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 AHR In Reset Position 3 — Final Downward Movement To Engage Locking Mechanism NOTE: 4. The AHR front soft foam and trim half should lock • If you have difficulties or problems resetting the into the back decorative plastic half.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System The front passenger seat BeltAlert is not active when the (BeltAlert ) front passenger seat is unoccupied. BeltAlert may be BeltAlert is a feature intended to remind the driver and triggered when an animal or heavy object is on the front front passenger (if equipped with front passenger passenger seat or when the seat is folded flat (if...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 2. Turn the ignition switch to the ON/RUN position (do NOTE: Although BeltAlert has been deactivated, the not start the engine), and wait for the Seat Belt Reminder Seat Belt Reminder Light will continue to illuminate Light to turn off.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender Supplemental Restraint System (SRS) - Airbags If a seat belt is too short, even when fully extended and This vehicle has Advanced Front Airbags for both the when the adjustable upper shoulder belt anchorage (if driver and front passenger as a supplement to the seat equipped) is in its lowest position, your authorized belt restraint systems.
Page 73
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the Advanced Front Airbags based upon seat position.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Instrument Panel This vehicle is equipped with Supplemental Seat- Mounted Side Airbags (SAB) to provide enhanced pro- • Supplemental Driver Side Knee Airbag tection for an occupant during a side impact. The SABs •...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Advanced Front Airbag Features WARNING! (Continued) The Advanced Front Airbag system has multistage driver • Do not put anything on or around the airbag and front passenger airbags. This system provides output covers or attempt to open them manually.
Page 76
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat-Mounted Side Airbags (SAB) When the airbag deploys, it opens the seam between the Supplemental Seat-Mounted Side Airbags provide en- front and side of the seat’s trim cover. Each airbag hanced protection to help protect an occupant during a deploys independently, that is a left side impact deploys side impact.
Page 77
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 • Airbag covers may not be obvious in the interior trim; WARNING! (Continued) but they will open during airbag deployment. • Do not use accessory seat covers or place objects • Being too close to the SAB and SABIC airbags during between you and the side airbags;...
Page 78
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE improved protection for the driver and front passenger. secured in the rear seat in child restraints or belt- Side airbags also work with seat belts to improve occu- positioning booster seats. Older children who do not use pant protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Do not lean against the door or window. If your vehicle WARNING! (Continued) has side airbags, and deployment occurs, the side airbags • Being too close to the steering wheel or instrument will inflate forcefully into the space between you and the panel during Advanced Front Airbag deployment door.
Page 80
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ORC deploys the Advanced Front Airbags, SABIC air- Advanced Front Airbags may deploy in crashes with bags, SABs, Supplemental Driver Side Knee Airbag, and little vehicle front-end damage but that produce a severe front seat belt pretensioners, as required, depending on initial deceleration.
Page 81
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 position, in the ACC position, or not in the ignition, the WARNING! airbag system is not on and the airbags will not inflate. Ignoring the Airbag Warning Light in your instru- The ORC contains a backup power supply system that ment panel could mean you won’t have the airbags to may deploy the airbags even if the battery loses power or protect you in a collision.
Page 82
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE based on the collision type and severity. The steering Driver Side Knee Airbag. The trim cover separates and wheel hub trim cover and the upper right side of the folds out of the way allowing the airbag to inflate to the instrument panel separate and fold out of the way as the full size.
Page 83
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 airbags fully inflate in about 10 milliseconds. The side and seated properly, or if items are positioned in the area airbag moves at a very high speed and with such a high where the side curtain airbag inflates.
Page 84
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE event the ORC will determine whether to have the If you do have a collision which deploys the airbags, any Enhanced Accident Response System perform the follow- or all of the following may occur: ing functions: •...
Page 85
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 throat irritation, move to fresh air. If the irritation Maintaining Your Airbag System continues, see your doctor. If these particles settle on WARNING! your clothing, follow the garment manufacturer’s in- structions for cleaning. •...
Page 86
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light WARNING! (Continued) You will want to have the airbags ready to • Do not attempt to modify any part of your ad- inflate for your protection in a collision. The vanced airbag system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 • Whether or not the driver and passenger safety belts NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint wer e buckled/fastened; Controller (ORC) may also be disabled. The airbags may •...
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the EDR.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 To obtain Integrated Child Seat replacement instruc- WARNING! tions: Refer to “Publication Order Forms” in If You Need Consumer Assistance and specify publication number In a collision, an unrestrained child, even a tiny baby, 81–016–8050 when ordering.
Page 90
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Safety experts recommend that children ride WARNING! rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types Rearward-facing child seats must never be used in of child restraints can be used rearward-facing: infant the front seat of a vehicle with a front passenger carriers and convertible child seats.
Page 91
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 • Check belt fit periodically. A child’s squirming or An aftermarket belt-positioning booster seat is for chil- dren weighing more than 40 lbs (18 kg), but who are still slouching can move the belt out of position. too small to properly fit the vehicle’s seat belts.
Page 92
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you make sure that you can install the child restraint in WARNING! the vehicle where you will use it, before you buy it. • Improper installation can lead to failure of an •...
Page 93
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 Installing the Child Restraint System In general, you will first loosen the child seat adjusters on We urge you to carefully follow the directions of the the lower straps and tether straps so that you can more manufacturer when installing your child restraint.
Page 94
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing The LATCH-Compatible Child Restraint NOTE: • When using the LATCH attaching system to install a System Each vehicle, except commercial cargo vehicles, child restraint, please ensure that all seat belts not is equipped with the child restraint anchorage being used for occupant restraints are stowed and out system called LATCH, which stands for Lower...
Page 95
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Installing the Lower Attachments: 4. Tighten the lower attachment strap while firmly push- ing the child restraint rearward and downward into the 1. The vehicle lower anchorages are round bars located vehicle seat. Remove all slack in the lower attachment at the rear of the seat cushion where it meets the seatback.
Page 96
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the Top Tether Strap (with either Lower Anchors or Vehicle Seat Belt): 1. Route the top tether strap under the adjustable head restraint between the steel posts. 2. Provide enough slack (reference child restraint in- structions) for the tether strap to reach the tether anchor located near the bottom of the seat back.
Page 97
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 description under “Seat Belts In Passenger Seating Posi- WARNING! tions” section. The chart below defines the seating posi- tions with an Automatic Locking Retractor (ALR) or a An incorrectly anchored tether strap could lead to cinching latch plate.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE then allow the belt to retract into the retractor. As the belt Transporting Pets retracts, you will hear a ratcheting sound. This indicates Airbags deploying in the front seat could harm your pet. the safety belt is now in the Automatic Locking mode.
Page 99
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 This vehicle is equipped with a child restraint tether WARNING! anchor located on the lower rear of the front passenger seat. Use this tether anchor to secure only forward- NEVER carry a child in a rear facing infant carrier in facing child restraints equipped with an upper tether a vehicle without rear seats.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • A convertible child seat, one that is designed to be Restraining Infants and Small Children with Seat Delete Feature (Commercial Vehicles Only) used for children who are too heavy for a rearward- There are different sizes and types of restraints for facing infant seat, may be used IN THE FORWARD children from newborn size to the child almost large...
Page 101
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 Tether Installation for Commercial Vehicles with 5. Following the child seat manufacturer’s instructions, Rear Seat Delete tighten the child restraint tether strap. To secure the child restraint upper tether strap to the 6.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS the recommended viscosity and quality grades refer to A long break-in period is not required for the engine and “Maintenance Procedures” in “Maintaining Your Ve- drivetrain (transmission and axle) in your vehicle. hicle”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Exhaust Gas WARNING! • Do not leave children or animals inside parked WARNING! vehicles in hot weather. Interior heat build-up may Exhaust gases can injure or kill. They contain carbon cause serious injury or death. monoxide (CO), which is colorless and odorless.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you are required to drive with the liftgate open, make Safety Checks You Should Make Inside The sure that all windows are closed and the climate control Vehicle BLOWER switch is set at high speed. DO NOT use the Seat Belts recirculation mode.
Page 105
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 Defroster WARNING! (Continued) Check operation by selecting the defrost mode and place • Always make sure that floor mats are properly the blower control on high speed. You should be able to feel attached to the floor mat fasteners.
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE lodged in the tread. Inspect the tread and sidewall for WARNING! (Continued) cuts and cracks. Check the wheel nuts for tightness. • Always make sure that objects cannot fall into the Check the tires (including spare) for proper pressure. driver foot well while the vehicle is moving.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Automatic Dimming Mirror — If Equipped CAUTION! This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or To avoid damage to the mirror during cleaning, never off by pressing the button at the base of the mirror.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Driver’s Automatic Dimming Mirror — If Equipped To receive maximum benefit, adjust the outside mirror(s) The driver’s outside mirror will automatically adjust for to center on the adjacent lane of traffic with a slight glare from vehicles behind you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Power Mirrors — If Equipped The power mirror controls consist of mirror select but- The power mirror controls are located on the driver-side tons and a four-way mirror control switch. To adjust a door trim panel.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Mirrors — If Equipped Reverse feature can be enabled or disabled in the Elec- These mirrors are heated to melt frost or ice. This tronic Vehicle Information Center (EVIC). Refer to “Elec- feature is activated whenever you turn on the rear tronic Vehicle Information Center (EVIC)/Customer- window defroster.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Illuminated Vanity Mirrors — If Equipped BLIND SPOT MONITORING — IF EQUIPPED An illuminated vanity mirror is located on the sun visor. The Blind Spot Monitoring (BSM) system uses two radar- To use the mirror, rotate the sun visor down and swing based sensors, located inside the rear bumper fascia, to the mirror cover upward.
Page 118
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The BSM system detection zone DOES NOT change if When the vehicle is started, the BSM warning light will momentarily illuminate in both outside rear view mirrors your vehicle is towing a trailer. Therefore, visually to let the driver know that the system is operational.
Page 119
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Sensor Locations BSM Warning Light The BSM system notifies the driver of objects in the The BSM system can also be configured to sound an detection zones by illuminating the BSM warning light audible (chime) alert and mute the radio to notify the located in the outside mirrors.
Page 120
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system monitors the detection zone from three Entering From The Rear different entry points (side, rear, front) while driving to Vehicles that come up from behind your vehicle on either see if an alert is necessary. The BSM system will issue an side and enter the rear detection zone with a relative alert during these types of zone entries.
Page 121
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Overtaking Traffic If you pass another vehicle slowly (with a relative speed of less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated.
Page 122
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can Modes Of Operation be obscured by vehicles parked on either side. If the Three selectable modes of operation are available in the sensors are blocked by other structures or vehicles, the Electronic Vehicle Information Center (EVIC).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 turn signal is then activated, and it corresponds to an Blind Spot Alert Off alert present on that side of the vehicle, an audible chime When the BSM system is turned off there will be no will also be sounded.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE VOICE COMMAND — IF EQUIPPED WARNING! (Continued) Voice Commands can be initiated by pressing the VR • Do not allow people to ride in any area of your button located on the radio or steering wheel vehicle that is not equipped with seats and seat controls (if equipped).
Page 127
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch when you have reached the desired position.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Do not place any article under a power seat or Moving a seat while driving could result in loss of impede its ability to move as it may cause damage to control which could cause a collision and serious the seat controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater.
Page 130
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can choose from HIGH, LOW or OFF heat settings. CAUTION! Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for Repeated overheating of the seat could damage the HIGH, one for LOW and none for OFF.
Page 131
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 When the HIGH-level setting is selected, the heater will provide a boosted heat level during the initial stages of operation. Then, the heat output will drop to the normal HIGH-level. If the HIGH-level setting is selected, the system will automatically switch to LOW-level after ap- proximately 30 minutes of continuous operation.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch once to select HIGH-level Manual Front/Second Row Seat Adjuster heating. Press the switch a second time to select Both front seats are adjustable forward or rearward. The LOW-level heating. Press the switch a third manual seat adjustment handle is located under the seat time to shut the heating elements OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 While sitting in the seat, pull up on the handle and slide Manual Reclining Seats — If Equipped the seat forward or rearward. Release the bar once you For models equipped with manual reclining seats, the have reached the desired position.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recline, lean forward slightly, lift the lever, then push WARNING! back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its The head restraints for all occupants must be prop- normal position.
Page 135
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts.
Page 136
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For comfort the Active Head Restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull outward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.
Page 137
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 NOTE: WARNING! • The head restraints should only be removed by quali- • Do not place items over the top of the Active Head fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- Restraint, such as coats, seat covers or portable rized dealer.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints — Second Row Quad Seats Head Restraints — Second Row Bench To raise the head restraint, pull upward on the head To raise the head restraint, pull upward on the head restraint.
Page 139
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 1. Raise the armrests on the second row seat. 3. Pull up on the seatback recliner lever on the outboard side of the seat. 2. Slide the storage bin locking mechanism to the “LOCK”...
Page 140
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pull Strap For 3rd Row Passengers Non-Adjustable Head Restraint The non-adjustable head restraint will fold automatically during the seat fold. No additional actuation is necessary. The seat will automatically fold into position for easy storage.
Page 141
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 CAUTION! The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. WARNING! In a collision, serious injury could result if the seat storage bin covers are not properly latched.
Page 142
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Unstow Second Row Seats 1. Pull up on the storage bin latch to open the cover. 2. Pull up on the strap to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Quad Seats — If Equipped Both Quad seats are adjustable forward or rearward. The manual seat adjustment handle is located under the seat cushion at the front edge of each seat. Folded Second Row Seat WARNING! In the event of a collision you could be injured if the seat is not fully latched.
Page 144
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE While sitting in the seat, pull up on the handle and slide Manual Recline the seat forward or rearward. Release the bar once you To recline, lean forward slightly, lift the lever, then push have reached the desired position.
Page 145
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Fold-Flat To fold the seat, lift the recliner lever to the full upward position and push the seatback forward until it rests on...
Page 146
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Entry For passengers seated in the third row, there is a pull The Quad seats can be tilted forward for easy entry into strap located on the outboard side of the seat near the the third row.
Page 147
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 To provide additional space behind the second row seats, Pull out the retainer strap from the sewn-in pocket the seats can be folded forward. located on the base of the seat cushion. With the seat in its fold-flat position, pull upward on the easy-access release lever and lift the seat into the desired position.
Page 148
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place the strap around the grab handle located on the Secure the retainer strap to the inside grab handle located B-Pillar. Before securing the strap, adjust the buckle for on the B-Pillar. When not in use, store the strap in the proper fit.
Page 149
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 WARNING! To reduce the risk of personal injury: • Retainer strap must always be securely attached to grab handle when seat is folded forward and vehicle is moving. • Never occupy the seat or the center seat behind a seat that has been folded forward.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row Bench Seat — If Equipped Release levers are located on the rear leg assemblies, near While the bench seat does not stow in the floor, it is the floor. To remove the seat, squeeze each release handle removable for added cargo space.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 To reinstall the seat, align the seat into the detent posi- tions on the floor. Squeeze the release handle and rotate upward until the lock indicator button returns into the handle. WARNING! If not properly latched, the bench seats could become loose.
Page 152
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Lower the head restraint by pulling on the release strap located on the outboard side of the head restraint. One Touch Folding Seat Third Row The rear switch bank allows multiple power folding and unfolding positions for the third row seats.
Page 153
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Left and right third row seats can be folded individually NOTE: • Disconnect the center shoulder belt from the small or together. The third row power folding seat adjusts to the following positions using the switch bank located on buckle and lower the head restraints before attempting the left rear trim panel: to fold/stow the power third row seats.
Page 154
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Fold Third Row Seats Manually — If Equipped 3. Pull release strap marked “1” located on the rear of the seat to lower the seatback. 1. Lower the center head restraint down to the seatback by pushing the button on the guide and pushing the head restraint down.
Page 155
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 4. Pull release strap marked “2” to release the anchors. 5. Pull release strap marked “3” and tumble the seat rearward into the storage bin. Release Strap “2” Release Strap “3”...
Page 156
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pulling strap “3” releases the seatback to return to its full upright position. 4. Raise the head restraint to its upright position. WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! To avoid serious injury or death, never operate the vehicle with occupants in the third row seat while in the tailgate mode. DRIVER MEMORY SEAT — IF EQUIPPED The Memory Buttons 1 and 2 on the driver’s door panel can be programmed to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting Memory Positions And Linking RKE 5. Turn on the radio and set the radio station presets (up Transmitter To Memory to 10 AM and 10 FM stations can be set). NOTE: Each time the SET (S) button and a numbered 6.
Page 159
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 11. Select Remote Linked to Memory in the Electronic To recall the memory setting for driver two, press Vehicle Information Center (EVIC) and enter “Yes”. Refer MEMORY button 2 on the driver’s door or the UNLOCK to “Electronic Vehicle Information Center (EVIC)/ button on the RKE transmitter linked to Memory Position Customer-Programmable Features”...
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Press and release the memory SET (S) button located Easy Entry/Exit Seat on the driver’s door. A chime will sound signaling that (Available With Memory Seat ONLY) you are in the memory set mode. This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 between 0.9 – 2.7 in (22.7 – 67.7 mm) forward of the TO OPEN AND CLOSE THE HOOD rear stop. The seat will return to its previously set To open the hood, two latches must be released. position when you insert the key into the ignition 1.
Page 162
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move to the front of the vehicle and look inside the CAUTION! center of the hood opening. Locate, then push the safety catch downward while raising the hood at the same time. To prevent possible damage, do not slam the hood to close it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 LIGHTS Interior Lighting All of the lights, except the Hazard Warning lights, Interior lights are turned on when a door or liftgate is headlight high beams and flash-to-pass, are controlled by opened, the Remote Keyless Entry (RKE) transmitter is switches to the left of the steering column on the instru- activated, or when the dimmer control is moved to the ment panel.
Page 164
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dimmer Switch Dimmer Control The dimmer switch is located to the right of the headlight With the parking lights or headlights on, rotating the switch. dimmer control for the interior lights on the instrument panel upward will increase the brightness of the instru- ment panel lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 The Halo control switch is located to the right of the Parking Lights dimmer switch. Turn the headlight switch knob to the first detent to turn on the parking lights. This also turns on all instrument panel lighting.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE will stay on for up to 90 seconds after you turn the To activate the delay feature, turn OFF the ignition switch ignition switch OFF. To turn the Automatic System off, while the headlights are still on. Then turn off the turn the headlight switch clockwise to the O (OFF) headlights within 45 seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 NOTE: The headlights must be turned off within 45 sec- Front Fog Lights — If Equipped onds of turning the ignition OFF to activate this feature. To activate the front fog lights, turn on the parking lights or the low beam headlights and push in the Lights-On Reminder headlight switch control knob.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Headlight Beams Low/High Multifunction Lever The multifunction lever is located on the left side of the • Flash-To-Pass (Optical Horn) steering column. • Front and Rear Wipers — Washer Functions Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Lane Change Assist WINDSHIELD WIPER AND WASHERS Tap the lever up or down once, without moving beyond The wipers and washers are operated by a switch within the detent, and the turn signal (right or left) will flash the multifunction lever.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE off position. If the windshield wiper switch is turned off desired. If the lever is pushed while on the intermittent and the blades cannot return to the off position, damage setting, the wipers will turn on and operate for several to the wiper motor may occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 NOTE: If the vehicle is moving less than 10 mph The sensitivity of the system is adjustable from the (16 km/h), delay times will be doubled. multifunction lever. Wiper sensitivity position 3 has been calibrated for best overall wiping sensitivity.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Rain Sensing feature can be turned on and off • Neutral Wipe Inhibit — The Rain Sensing feature will through the EVIC (if equipped). Refer to “Electronic not operate when the ignition is ON, and the trans- Vehicle Information Center (EVIC)/Personal Settings mission shift lever is in the NEUTRAL position, and (Customer-Programmable Features)”...
Page 173
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 shorten the steering column. The tilt/telescoping lever is To unlock the steering column, push the lever downward located below the steering wheel at the end of the (toward the floor). To tilt the steering column, move the steering column.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HEATED STEERING WHEEL — IF EQUIPPED NOTE: The engine must be running for the heated The steering wheel contains a heating element that helps steering wheel to operate. warm your hands in cold weather. The heated steering Vehicles Equipped with Remote Start wheel has only one temperature setting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 WARNING! (Continued) • Do not place anything on the steering wheel that insulates against heat, such as a blanket or cush- ion. This may cause the steering wheel heater to overheat. ADJUSTABLE PEDALS — IF EQUIPPED The adjustable pedals system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals cannot be adjusted when the vehicle is in WARNING! REVERSE or when the Electronic Speed Control Sys- tem is on. The following messages will be displayed Do not adjust the pedals while the vehicle is moving. on vehicles equipped with the Electronic Vehicle In- You could lose control and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The Cruise Indicator Light in the instrument cluster will illuminate. To turn the system off, push the ON/OFF button a second time.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set A Desired Speed To Vary The Speed Setting Turn the Electronic Speed Control ON. When the vehicle When the Electronic Speed Control is set, you can in- has reached the desired speed, press the SET (-) button crease speed by pushing the RES (+) button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 To Accelerate For Passing WARNING! Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Electronic Speed Control can be dangerous where the system cannot maintain a constant speed.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense will retain the last system state (enabled or ParkSense Warning Display disabled) from the last ignition cycle when the ignition is The ParkSense Warning screen will only be displayed if changed to the ON/RUN position. Sound and Display is selected from the Customer- Pro- grammable Features section of the Electronic Vehicle ParkSense can be active only when the shift lever is in...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 ParkSense Display When the vehicle is in REVERSE, the warning display will turn ON indicating the system status. ParkSense Warning Display Park Assist ON...
Page 182
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
Page 183
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Fast Tone Continuous Tone The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle:...
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING ALERTS Rear Distance Greater than 79-39 in 39-25 in 25-12 in Less than (in/cm) 79 in (200 cm) (200-100 cm) (100-65 cm) (65-30 cm) 12 in (30 cm) Audible Alert None Single 1/2 Slow Fast Continuous...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 approximately five seconds. Refer to “Electronic Vehicle Service The ParkSense Rear Park Assist System Information Center (EVIC)” in “Understanding Your When the ParkSense Rear Park Assist System is mal- Instrument Panel” for further information. When the functioning, the instrument cluster will actuate a single shift lever is moved to REVERSE and the system is chime, once per ignition cycle, and it will display the...
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When you turn ParkSense off, the instrument cluster If “SERVICE PARK ASSIST SYSTEM” appears in the EVIC, see your authorized dealer. will display “PARK ASSIST OFF.” Furthermore, once you turn ParkSense off, it remains off until you turn Cleaning ParkSense it on again, even if you cycle the ignition key.
Page 187
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 • Objects such as bicycle carriers, trailer hitches, etc., CAUTION! must not be placed within 12 in (30 cm) from the rear • ParkSense is only a parking aid and it is unable fascia/bumper while driving the vehicle.
Page 188
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Before using the ParkSense Rear Park Assist • Drivers must be careful when backing up even System, it is strongly recommended that the ball when using the ParkSense Rear Park Assist Sys- mount and hitch ball assembly is disconnected tem.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 PARKVIEW REAR BACK UP CAMERA — When the vehicle is shifted out of REVERSE, the rear IF EQUIPPED camera mode is exited and the navigation or audio screen Your vehicle may be equipped with the ParkView Rear appears again.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! (Continued) • To avoid vehicle damage, the vehicle must be Drivers must be careful when backing up even when driven slowly when using ParkView to be able to using the ParkView Rear Back Up Camera. Always stop in time when an obstacle is seen.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 4. Enable or disable the rear camera feature by selecting illuminates the instrument panel cupholders, two swiv- “enable rear camera in reverse” soft key. eling LED lights, flip-down sunglass storage, conversa- tion mirror, optional power sliding door switches and an 5.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Interior Lighting Sunglass Storage (Non-Sunroof Only) At the forward end of the console are two courtesy lights At the front of the overhead console, a compartment is (standard dome light has two buttons). The lights turn on provided for the storage of two pairs of sunglasses.
Page 193
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Full Open Position Conversation Mirror Position From this position, the door can be fully closed or, by NOTE: From the “conversation mirror” position, the rotating upward about 3/4 of the way and releasing, door can only be closed.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 Rear Console Halo Lighting The rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to “Lights/ Halo Lights —...
Page 196
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink buttons that are located in the headliner WARNING! or sun visor designate the three different HomeLink • Your motorized door or gate will open and close channels. while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 Programming HomeLink Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink button you wish to pro- Before You Begin gram while keeping the indicator light in view. If you have not trained any of the HomeLink buttons, •...
Page 198
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After training a HomeLink channel, if the garage This can usually be found where the hanging antenna door does not operate with HomeLink and the ga- wire is attached to the garage door opener motor. It is rage door opener was manufactured after 1995, the NOT the button normally used to open and close the garage door opener may have a rolling code.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 1. Firmly press and release the LEARN or TRAINING Gate Operator/Canadian Programming button. The name and color of the button may vary by Canadian radio frequency laws require transmitter sig- manufacturer. nals to time-out (or quit) after several seconds of trans- mission –...
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Continue to press and hold the HomeLink button, Reprogramming A Single HomeLink Button while you press and release (“cycle”), your handheld To reprogram a channel that has been previously trained, follow these steps: transmitter every two seconds until HomeLink has successfully accepted the frequency signal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 The HomeLink Universal Transceiver is disabled when General Information the Vehicle Security Alarm is active. This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following Troubleshooting Tips two conditions: If you are having trouble programming HomeLink , here...
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED Power Sunroof Operation The power sunroof control switch is located in the front Opening The Sunroof Manually overhead console. Press the switch rearward and hold, and the sunroof will open automatically from any position.
Page 203
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Closing The Sunroof Manually Express Open To close the sunroof from an open or vent position, press Press the switch rearward and release, and the sunroof and hold the switch forward. The sunroof will close fully will open automatically from any position.
Page 204
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Auto Express will stop and reverse travel up to three WARNING! times in succession. After the third time, Auto Express will enter a manual operation mode. This allows the Do not allow small children to operate the sunroof. operator to manually control the power switch, in order Never allow your fingers, other body parts, or any to close or open the sunroof in case of a malfunction.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. ELECTRICAL POWER OUTLETS — IF EQUIPPED Two 12 Volt (13 Amp) power outlets are located on the lower instrument panel, below the open storage bin.
Page 206
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE One outlet in the removable floor console (if equipped) On vehicles equipped with the Super Console the power shares a fuse with the lower outlet in the instrument outlets are located under the retractable cover. To access panel and is also connected to the battery.
Page 207
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both con- trolled by the ignition switch. Each of these outlets can support 160 Watts (13 Amps). Do not exceed 160 Watts (13 Amps) for each of these outlets.
Page 208
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Only devices designed for use in this type of power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 CAUTION! (Continued) • Power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Improper use of the power outlet can cause damage. POWER INVERTER —...
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This outlet can power cellular phones, electronics and for easy removal. Refer to “Cleaning The Instrument other low power devices requiring power up to 150 Panel Cupholders” in “Maintaining Your Vehicle” for Watts. Certain high-end video games, such as Playsta- further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 Pull the drawer out firmly until it stops, and place the container to be held in either one of the cupholder wells. The cupholders are designed to accommodate a wide variety of container types and sizes. Press down on the container to engage the cupholder retention features.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For rear passengers two cupholders are located in the Premium Console Cupholders — If Equipped pull-out drawer, located in the back of the Super Console. On models equipped with premium center consoles, Pull the drawer out to the first position to use the there are four cupholders located on the top of the cupholders.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Smoker’s Package Kit — If Equipped STORAGE With the optional authorized dealer-installed Smoker’s Glove Compartments Package Kit, a removable ash receiver is inserted into one Upper and lower glove compartments are located on the of the two cupholders in the center front instrument passenger side of the instrument panel.
Page 215
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 Upper Glove Compartment Lower Glove Compartment To open the upper compartment, press in on the button, To open the lower compartment pull out on the release located on the left side of the upper door. The door will handle.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Trim Panel Storage Front Door Storage Both interior front door panels have multiple pockets for storage. Driver Seatback Storage — If Equipped The driver’s seatback has a primary storage pocket on all models and an optional secondary mesh pocket.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the Lock position to allow greater access to the storage bin. Umbrella Holder Second Row Seat Storage Bins — If Equipped The seat storage bins are located on the floor in front of the second row seats.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage Bin Safety Warning CAUTION! Carefully follow these warnings to help prevent personal injury or damage to your vehicle: NOTE: The storage bin cover must be locked and flat to avoid damage from contact with the front seat WARNING! tracks, which have minimal clearance to the cover.
Page 219
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 WARNING! (Continued) • Do not operate the storage bin covers while the vehicle is in motion. • Do not use a storage bin latch as a tie down. CAUTION! The storage bin cover must be flat and locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 CONSOLE FEATURES To Remove The Basic Floor Console There are three consoles available: Basic, Premium and 1. Remove the front anchor cup plug and clip. Super. 2. Slide the console base forward while lifting slightly to Basic Console clear the rear load floor hook.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Upper storage bin can hold nine regular or 18 thin CDs 5. Pull up on the console to be sure it is firmly latched. or other items WARNING! • Large console center storage will store headphones for the available rear DVD entertainment system or other In an accident, serious injury could result if the items...
Page 223
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 Position 1 shows the console closed with four cupholders Position 2 shows the raised storage tray revealing a large and a convenient storage tray. storage area below. Console Position 1 Console Position 2...
Page 224
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dual Storage Bins Position 4 shows the complete console in its rearmost Position 3 shows the top portion of the console in a position. Again, lifting second latch handle at the front of rearward position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 To Remove The Premium Floor Console 4. Push down on the rear of the console until it is seated in the rear floor bracket. 1. Pull up on the bottom release handle in the front of the console.
Page 226
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The super console contains a pass through storage area accessible for both the driver and front passenger. Super Console 1 — Front Sliding Tambour Door 2 — Cupholder Light Ring Front Lower Pass Through 3 —...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 NOTE: The front cupholder light ring and pass through REAR WINDOW FEATURES lighting is controlled by a dimming switch located on the Rear Window Defroster instrument panel, refer to “Lights” in “Understanding The rear window defroster button is located on the The Features Of Your Vehicle”...
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE A hydraulic pump contained within the shock absorbers CAUTION! raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling Failure to follow these cautions can cause damage to to complete depending on road surface conditions.
Page 229
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 The crossbars and side rails are designed to carry weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. NOTE: •...
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Deploying the Crossbars CAUTION! To deploy the crossbars, completely loosen the thumb screws at both ends of the crossbar and lift the crossbar Use care when removing and handling the crossbars from its stowed position in the side rail. Repeat with to prevent damage to the vehicle.
Page 231
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 NOTE: The crossbars are identical and can be placed in any two of the three deploy positions. Deployed Position Then, position the crossbars across the roof. Deploy Positions...
Page 232
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Make sure the directional arrow on the crossbars aligns with the directional arrows on the side rails. Set the crossbars into the deployed positions. Tightening Crossbar Stowing the Crossbars Reverse the procedure to stow the crossbars. Crossbars are identical and can be stowed in either rail nest.
Page 233
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 NOTE: Load should always be secured to crossbars CAUTION! first, with rail tie down loops used as additional securing • Check deployed crossbars frequently and re- points if needed. Tie loops are intended as supplemen- tary tie down points only.
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) WARNING! • Long loads which extend over the windshield, Cargo must be securely tied before driving your such as wood panels or surfboards, or loads with vehicle. Improperly secured loads can fly off the large frontal area should be secured to both the vehicle, particularly at high speeds, resulting in per- front and rear of the vehicle.
Page 235
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 Sun Screen Retracted Sun Screen Extended Gently pull up on the tab to raise the sun screen. To lower the sun screen, gently lift the tab upward to Continue pulling the sun screen until the tab is near the disengage the hooks, and feed the screen back into the top of the window.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....239 Electronic Vehicle Information Center (EVIC) — If Equipped ......259 Instrument Cluster —...
Page 238
236 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Compass / Temperature Display ..271 ▫ Operation Instructions - Auxiliary Mode ..287 ▫ Customer-Programmable Features Media Center 130 With Satellite Radio (System Setup) .
Page 239
UNDERSTANDING YOUR INSTRUMENT PANEL 237 iPod /USB/MP3 Control — If Equipped ..304 Steering Wheel Audio Controls — If Equipped ......312 ▫...
Page 240
238 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Automatic Temperature Control (ATC) — ▫ Window Fogging ....338 If Equipped ......327 ▫...
242 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 4. Turn Signal Indicators The arrow will flash with the exterior turn signal 1. Tachometer when the turn signal lever is operated. The red segments indicate the maximum permissible engine revolutions per minute (RPM x 1000) for each gear If the vehicle is driven 1 mile (1.6 km) with either turn range.
Page 245
UNDERSTANDING YOUR INSTRUMENT PANEL 243 6. Compass Mini-Trip Computer (CMTC) or Electronic Message Display Area Vehicle Information Center (EVIC) Display — When the appropriate conditions exist, the following If Equipped odometer messages will display: door ......Door Ajar Odometer gATE .
Page 246
244 UNDERSTANDING YOUR INSTRUMENT PANEL LoW tirE CHAngE OIL When the appropriate condition exists, the odometer Your vehicle is equipped with an engine oil change display will toggle between LoW and tirE for three indicator system. The CHAngE OIL message will flash in cycles.
Page 247
UNDERSTANDING YOUR INSTRUMENT PANEL 245 2. Fully depress the accelerator pedal, slowly, three times Electronic Vehicle Information Center (EVIC) within 10 seconds. Display — If Equipped The Electronic Vehicle Information Center (EVIC) fea- 3. Turn the ignition switch to the OFF/LOCK position. tures a driver-interactive display that is located in the NOTE: If the indicator message illuminates when you instrument cluster.
Page 248
246 UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light is on, the brake system should be serviced As an added safety feature, your vehicle has been as soon as possible to restore the benefits of Anti-Lock equipped with a Tire Pressure Monitoring System brakes.
Page 249
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Your vehicle has also been equipped with a TPMS CAUTION! malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is The TPMS has been optimized for the original combined with the low tire pressure telltale. When the equipment tires and wheels.
Page 250
248 UNDERSTANDING YOUR INSTRUMENT PANEL does not come on when turning the key from OFF to WARNING! ON/RUN, have the condition checked promptly. A malfunctioning catalytic converter, as referenced Certain conditions such as a loose or missing gas cap, above, can reach higher temperatures than in normal poor fuel quality, etc., may illuminate the MIL after operating conditions.
Page 251
UNDERSTANDING YOUR INSTRUMENT PANEL 249 system. If this light remains on after several ignition 11. Electronic Stability Control (ESC) OFF Indicator cycles, and the vehicle has been driven several miles Light — If Equipped (kilometers) at speeds greater than 30 mph (48 km/h), see This light indicates the Electronic Stability Con- your authorized dealer as soon as possible to have the trol (ESC) is off.
Page 252
250 UNDERSTANDING YOUR INSTRUMENT PANEL • The highest available transmission gear is displayed in 15. Airbag Warning Light This light will turn on for four to eight seconds the lower right corner of the Electronic Vehicle Infor- as a bulb check when the ignition switch is first mation Center (EVIC) whenever the Electronic Range turned to ON/RUN.
Page 253
UNDERSTANDING YOUR INSTRUMENT PANEL 251 If the light remains on when the parking brake has been NOTE: The light may flash momentarily during sharp disengaged, and the fluid level is at the full mark on the cornering maneuvers, which change fluid level condi- master cylinder reservoir, it indicates a possible brake tions.
Page 254
252 UNDERSTANDING YOUR INSTRUMENT PANEL Operation of the Brake Warning Light can be checked by 19. Seat Belt Reminder Light turning the ignition switch from the OFF position to the When the ignition switch is first turned to ON/ ON/RUN position. The light should illuminate for ap- RUN, this light will turn on for four to eight proximately two seconds.
Page 255
UNDERSTANDING YOUR INSTRUMENT PANEL 253 CAUTION! WARNING! Driving with a hot engine cooling system could A hot engine cooling system is dangerous. You or damage your vehicle. If temperature gauge reads “H” others could be badly burned by steam or boiling pull over and stop the vehicle.
Page 256
254 UNDERSTANDING YOUR INSTRUMENT PANEL while driving, turn off some of the vehicle’s non-essential 24. Engine Temperature Warning Light electrical devices or increase engine speed (if at idle). If This light warns of an overheated engine condi- the charging system light remains on, it means that the tion.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 25. Electronic Throttle Control (ETC) Light COMPASS MINI-TRIP COMPUTER (CMTC) — This light informs you of a problem with the IF EQUIPPED Electronic Throttle Control (ETC) system. The NOTE: light will come on when the ignition is first •...
256 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The system will display the last known outside When the appropriate conditions exist, the following temperature when starting the vehicle and may need to messages will display: be driven several minutes before the updated tempera- NE .
UNDERSTANDING YOUR INSTRUMENT PANEL 257 CMTC Trip Odometer (ODO) Compass/Temperature Display This display shows the distance traveled since the last Compass Variance reset. Press and release the STEP button on the steering Compass Variance is the difference between Magnetic wheel to switch from odometer, to Trip A or Trip B, or to North and Geographic North.
Page 260
258 UNDERSTANDING YOUR INSTRUMENT PANEL • Magnetic and battery powered devices, (such as cell To Set The Variance phones, iPod’s, radar detectors, PDA’s and laptops) Start the engine and leave the transmission gear selector should be kept away from the top of the instrument lever in the PARK position.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 2. Press and hold the RESET button (for approximately 10 seconds) until the current variance zone number is displayed. 3. Release the RESET button, then press and hold again for approximately 10 seconds, until the direction is displayed, with the CAL indicator on continuously in the display.
Page 262
260 UNDERSTANDING YOUR INSTRUMENT PANEL • Vehicle information warning message displays The system allows the driver to select information by pressing the following buttons mounted on the steering • Tire Pressure Monitor System wheel: • Personal Settings (Customer-Programmable Features) • Compass display •...
UNDERSTANDING YOUR INSTRUMENT PANEL 261 UP Button BACK Button Press and release the UP button to scroll up- Press the BACK button to scroll back to a ward through the main menus (Fuel Economy, previous menu or sub menu. Vehicle Info, Tire PSI, Cruise, Messages, Units, System Setup) and sub menus.
Page 264
262 UNDERSTANDING YOUR INSTRUMENT PANEL • Remote start active — Push Start Button • Service TPM System (refer to “Tire Pressure Monitor- ing System” in “Starting And Operating”) • Remote start active — Key to Run • Turn Signal On •...
Page 265
UNDERSTANDING YOUR INSTRUMENT PANEL 263 • Blind Spot System Off — This message is displayed EVIC White Telltale Lights when the ignition is turned to ON to indicate the Blind This area will show reconfigurable white caution tell- Spot System has been turned off. tales.
Page 266
264 UNDERSTANDING YOUR INSTRUMENT PANEL • Electronic Speed Control SET to turn off the message. If the problem continues, the This light will turn on when the electronic message will appear the next time the vehicle is started. speed control is SET. For further information, A loose, improperly installed, or damaged fuel filler cap refer to “Electronic Speed Control”...
Page 267
UNDERSTANDING YOUR INSTRUMENT PANEL 265 • Oil Pressure Warning Light vehicle is experiencing a problem with the charging This light indicates low engine oil pressure. The system. Obtain SERVICE IMMEDIATELY. See an autho- light should turn on momentarily when the engine rized dealer.
Page 268
266 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains lit with the engine running your shift the transmission into NEUTRAL and idle the ve- vehicle, will usually be drivable, however, see an autho- hicle. If the temperature reading does not return to rized dealer for service as soon as possible.
Page 269
UNDERSTANDING YOUR INSTRUMENT PANEL 267 Unless reset, this message will continue to display each WARNING! time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and If the Transmission Temperature Warning Light is release the Menu button.
268 UNDERSTANDING YOUR INSTRUMENT PANEL Fuel Economy “RESET” or show dashes for two seconds. Then, the Press and release the UP or DOWN button until “Fuel history information will be erased, and the averaging will Economy” displays highlighted in the EVIC and press continue from the last fuel average reading before the the SELECT button.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 Distance To Empty (DTE) Vehicle Speed Shows the estimated distance that can be traveled with Press and release the UP or DOWN button until “Vehicle the fuel remaining in the tank. This estimated distance is Speed”...
270 UNDERSTANDING YOUR INSTRUMENT PANEL • Elapsed Time To Reset The Display Reset will only occur while a resettable function is being Press the UP/DOWN buttons to cycle through all the displayed. Press and release the SELECT button once to Trip Computer functions.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 Vehicle Info (Customer Information Features) Compass / Temperature Display Press and release the UP or DOWN button until “Vehicle The compass readings indicate the direction the vehicle is Info” displays in the EVIC and press the SELECT button. facing.
Page 274
272 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: A good calibration requires a level surface and 5. Complete one or more 360–degree turns (in an area an environment free from large metallic objects such as free from large metal or metallic objects) until the “CAL” buildings, bridges, underground cables, railroad tracks, indicator turns off.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 3. Press the DOWN button until the “Compass Variance” message is displayed in the EVIC, then press the SELECT button. The last variance zone number displays in the EVIC. 4. Press and release the SELECT button until the proper variance zone is selected, according to the map.
Page 276
274 UNDERSTANDING YOUR INSTRUMENT PANEL Language is removed, showing the system has been deactivated. When in this display you may select one of five lan- Refer to “Rear Park Assist System” in “Understanding guages for all display nomenclature, including the trip The Features Of Your Vehicle”...
Page 277
UNDERSTANDING YOUR INSTRUMENT PANEL 275 transmitter UNLOCK button twice, to unlock the passen- Sound Horn with Remote Key Lock ger’s doors. When All Doors 1st Press is selected, all of When ON is selected, a short horn sound will occur when the doors will unlock on the first press of the RKE the RKE transmitter LOCK button is pressed.
Page 278
276 UNDERSTANDING YOUR INSTRUMENT PANEL Headlamp Off Delay Easy Exit Seat When this feature is selected, the driver can choose to This feature provides automatic driver seat positioning to have the headlights remain on for 0, 30, 60, or 90 seconds enhance driver mobility when entering and exiting the when exiting the vehicle.
Page 279
UNDERSTANDING YOUR INSTRUMENT PANEL 277 To make your selection, press and release the SELECT unlocked with the RKE transmitter. To make your selec- button until a check-mark appears next to the feature tion, scroll up or down until the preferred setting is showing the system has been activated or the check-mark highlighted, then press and release the SELECT button is removed, showing the system has been deactivated.
278 UNDERSTANDING YOUR INSTRUMENT PANEL To make your selection, press and release the SELECT Calibrate Compass button until a check-mark appears next to the feature Refer to “Compass Display” for more information. showing the system has been activated or the check-mark Compass Variance is removed, showing the system has been deactivated.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 Operating Instructions (Voice Command System) — If Equipped Refer to “Voice Command” in the Uconnect™ User Manual located on the DVD for further details. Operating Instructions (Uconnect™ Phone) — If Equipped Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details.
Page 282
280 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) TIME Button Push the ON/VOLUME control knob to turn on the Press the TIME button to alternate display of the time radio. Push the ON/VOLUME control knob a second and radio frequency. time to turn off the radio.
Page 283
UNDERSTANDING YOUR INSTRUMENT PANEL 281 RW/FF Push the rotary TUNE/SCROLL control knob a third Pressing the RW (Rewind) or FF (Fast Forward) buttons time and TREBLE will display. Turn the TUNE/SCROLL causes the tuner to search for the next frequency in the control knob to the right or left to increase or decrease the direction of the arrows.
282 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button — To Set the Pushbutton Memory Buttons 1 - 6 When you are receiving a station that you wish to These buttons tune the radio to the stations that you commit to pushbutton memory, press the SET/RND commit to pushbutton memory (12 AM and 12 FM button.
Page 285
UNDERSTANDING YOUR INSTRUMENT PANEL 283 Inserting Compact Disc(s) CAUTION! (Continued) Gently insert one CD into the CD player with the CD • Do not use adhesive labels. These labels can peel label facing up. The CD will automatically be pulled into away and jam the player mechanism.
284 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Ejecting with the ignition OFF is not allowed on AM/FM Button convertible or soft-top models (if equipped). Press the button to select either AM or FM mode. SEEK Button SET/RND Button (Random Play Button) Press the right SEEK button for the next selection on the Press this button while the CD is playing to activate CD.
Page 287
UNDERSTANDING YOUR INSTRUMENT PANEL 285 Supported Media (Disc Types) a number instead. With a maximum number of files, The MP3 file recording media supported by the radio are exceeding 20 folders will result in this display. With CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. 200 files, exceeding 50 folders will result in this display.) Supported Medium Formats (File Systems)
Page 288
286 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats MPEG Sampling Fre- Bit Rate (kbps) The radio will recognize only files with the *.MP3 exten- Specification quency (kHz) sion as MP3 files. Non-MP3 files named with the *.MP3 320, 256, 224, 192, extension may cause playback problems.
UNDERSTANDING YOUR INSTRUMENT PANEL 287 Playback of MP3 Files Operation Instructions - Auxiliary Mode When a medium containing MP3 data is loaded, the The auxiliary (AUX) jack is an audio input jack, which radio checks all files on the medium. If the medium allows the user to plug in a portable device, such as an contains a lot of folders or files, the radio will take more MP3 player, or cassette player, and utilize the vehicle’s...
288 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 WITH SATELLITE RADIO Operating Instructions — Radio Mode (SALES CODE RES+RSC) NOTE: The ignition switch must be in the ON/RUN or NOTE: The radio sales code is located on the lower right ACC position to operate the radio.
Page 291
UNDERSTANDING YOUR INSTRUMENT PANEL 289 SEEK Buttons If your vehicle is not equipped with or this feature is not Press and release the SEEK buttons to search for the next available on your vehicle, a “Not Equipped With listenable station in AM/FM mode. Press the right switch Uconnect Phone”...
Page 292
290 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure starting at Step 2. For vehicles not equipped with satellite radio, press the SETUP button and then follow the above 1. Press and hold the TIME button until the hours blink. procedure, starting at Step 2. 2.
Page 293
UNDERSTANDING YOUR INSTRUMENT PANEL 291 Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob a fifth time Push the rotary TUNE/SCROLL control knob and BASS and FADE will display. Turn the TUNE/SCROLL control will display. Turn the TUNE/SCROLL control knob to knob to the left or right to adjust the sound level between the right or left to increase or decrease the bass tones.
Page 294
292 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following Program Type 16-Digit Character Display format types: Public Public Program Type 16-Digit Character Display Rhythm and Blues R & B No program type or Religious Music Rel Musc None undefined...
Page 295
UNDERSTANDING YOUR INSTRUMENT PANEL 293 If a preset button is activated while in the Music Type SET/RND Button — To Set the Pushbutton (Program Type) mode, the Music Type mode will be Memory exited and the radio will tune to the preset station. When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND SETUP Button...
294 UNDERSTANDING YOUR INSTRUMENT PANEL Every time a preset button is used, a corresponding discs (CD-RW), compact discs with MP3 tracks and button number will display. multisession compact discs with CD and MP3 tracks. Buttons 1 - 6 Inserting Compact Disc(s) These buttons tune the radio to the stations that you Gently insert one CD into the CD player with the CD commit to pushbutton memory (12 AM and 12 FM...
Page 297
UNDERSTANDING YOUR INSTRUMENT PANEL 295 If you have ejected a disc and have not removed it within CAUTION! 10 seconds, it will be reloaded. If the CD is not removed, • This CD player will accept 4–3/4 in (12 cm) discs the radio will reinsert the CD but will not play it.
296 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Notes On Playing MP3 Files Press and hold FF (Fast Forward) and the CD player will The radio can play MP3 files; however, acceptable MP3 begin to fast forward until FF is released or RW or file recording media and formats are limited.
Page 299
UNDERSTANDING YOUR INSTRUMENT PANEL 297 • Maximum number of files: 255 Discs created with an option such as keep disc open after writing are most likely multisession discs. The use of • Maximum number of folders. (The radio display of file multisession for CD audio or MP3 playback may result in names and folder names is limited.
Page 300
298 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files MPEG Sampling Fre- Bit Rate (kbps) When a medium containing MP3 data is loaded, the Specification quency (kHz) radio checks all files on the medium. If the medium 320, 256, 224, 192, contains a lot of folders or files, the radio will take more MPEG-1 Audio 160, 128, 112, 96,...
UNDERSTANDING YOUR INSTRUMENT PANEL 299 LIST Button (CD Mode for MP3 Play) Press and hold the INFO button again for three seconds Pressing the LIST button will bring up a list of all folders to return to elapsed time display. on the disc.
300 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) radio system in your vehicle. Sirius will supply a wel- Press this button to change the display to time of day. The come kit that contains general information, including time of day will display for five seconds (when the how to setup your on-line listening account.
Page 303
UNDERSTANDING YOUR INSTRUMENT PANEL 301 using the TUNE/SCROLL control knob until Sirius ID is Reception Quality selected. Press the TUNE/SCROLL control knob and the Satellite reception may be interrupted due to one of the Sirius ID number will display. The Sirius ID number following reasons: display will time out in two minutes.
Page 304
302 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons RW/FF Press and release the SEEK buttons to search for the next Pressing the RW (Rewind) or FF (Fast Forward) buttons channel in Satellite mode. Press the right switch to seek causes the tuner to search for the next channel in the up and the left switch to seek down.
Page 305
UNDERSTANDING YOUR INSTRUMENT PANEL 303 If a preset button is activated while in the Music Type selected within five seconds after pressing the SET but- (Program Type) mode, the Music Type mode will be ton, the channel will continue to play but will not be exited and the radio will tune to the preset channel.
304 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions (Uconnect™ Phone) — iPod control supports Mini, 4G, Photo, Nano, 5G iPod If Equipped and iPhone devices. Some iPod software versions may Refer to “Uconnect™ Phone” in the Uconnect™ User not fully support the iPod control features. Please visit Manual located on the DVD for further details.
UNDERSTANDING YOUR INSTRUMENT PANEL 305 NOTE: If the audio device battery is completely dis- charged, it may not communicate with the iPod /USB/ MP3 control system until a minimum charge is attained. Leaving the audio device connected to the iPod /USB/ MP3 control system may charge it to the required level.
306 UNDERSTANDING YOUR INSTRUMENT PANEL • Turning it counterclockwise (backward) by one Controlling The iPod or External USB Device Using Radio Buttons click, will jump to the previous track in the list or To get into the iPod /USB/MP3 control mode and access press VR button and say Previous Track a connected audio device, either press the “AUX”...
UNDERSTANDING YOUR INSTRUMENT PANEL 307 • While a track is playing, press the INFO button to see • RND button (available on sales code RES radio only): the associated metadata (artist, track title, album, etc.) Pressing this button toggles between Shuffle ON and for that track.
Page 310
308 UNDERSTANDING YOUR INSTRUMENT PANEL • Preset 5 – Audiobooks press the TUNE control knob to select and start playing the track. Turning the TUNE control knob • Preset 6 – Podcasts fast will scroll through the list faster. During fast •...
UNDERSTANDING YOUR INSTRUMENT PANEL 309 • MUSIC TYPE button: The MUSIC TYPE button is WARNING! another shortcut button to the genre listing on your audio device. Do not plug in or remove the iPod or external USB device while driving. Failure to follow this warning CAUTION! could result in an accident.
310 UNDERSTANDING YOUR INSTRUMENT PANEL phone system. Seven devices can be paired to Uconnect™ Browse phone system, but just one can be selected and played. Browsing is not available on a BTSA device. Only the current song that is playing will display info. Selecting different Audio Device VIDEO ENTERTAINMENT SYSTEM (VES)™...
Page 313
UNDERSTANDING YOUR INSTRUMENT PANEL 311 • Three different medias can be played simultaneously (Cabin speakers and Headphone Channels 1 and 2) • Easy menu-driven functions on touch-screen radios • Video and audio input jacks available in rear seating area • Ten different medias to choose from in each screen (AM, FM, Sirius Radio, Sirius Backseat TV™, DVD1, DVD2, Hard Disc Drive (HDD), AUX in radio, AUX1, AUX2)
312 UNDERSTANDING YOUR INSTRUMENT PANEL STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED VES™ Remote Control Location NOTE: Refer to the “Uconnect™ Multimedia” section of Uconnect™ User Manual located on the DVD for further Remote Sound System Controls details. (Back View Of Steering Wheel) The remote sound system controls are located on the rear surface of the steering wheel, at the three and nine o’clock positions.
UNDERSTANDING YOUR INSTRUMENT PANEL 313 The right-hand rocker switch has a pushbutton in the Radio Operation center, and controls the volume and mode of the sound Pressing the top of the switch will SEEK up for the next system. Pressing the top of the rocker switch will increase listenable station, and pressing the bottom of the switch the volume.
314 UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD DISC MAINTENANCE NOTE: If you experience difficulty in playing a particu- To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding.
UNDERSTANDING YOUR INSTRUMENT PANEL 315 CLIMATE CONTROLS The Climate Control system allows you to regulate the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel, below the radio. Manual Heating and Air Conditioning System — If Equipped The controls for the manual system in this vehicle contain a series of outer rotary dials and inner push knobs.
Page 318
316 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Front Blower Control 4. Mix Mode Use this control to regulate the amount of air forced Air is directed through the floor, defrost and side through the system in any mode you select. The blower window demist outlets.
Page 319
UNDERSTANDING YOUR INSTRUMENT PANEL 317 6. Electronic Rear Window Defrost CAUTION! Press this button to turn on the rear window defroster and the heated outside mirrors (if Failure to follow these cautions can cause damage to equipped). An indicator in the button will illuminate the heating elements: when the rear window defroster is on.
Page 320
318 UNDERSTANDING YOUR INSTRUMENT PANEL • In order to prevent fogging, when the RECIRCULA- RECIRCULATION mode. Only use the RECIRCULA- TION mode to temporarily block out any outside odors, TION button is pressed and the mode control is set to smoke, or dust, and to cool the interior rapidly upon PANEL, the A/C will engage automatically.
UNDERSTANDING YOUR INSTRUMENT PANEL 319 9. Floor Mode Button NOTE: For maximum airflow to the rear, the center Air is directed through the floor outlets with a instrument panel outlets can be directed toward the rear small amount through the defrost and side window seat passengers.
Page 322
320 UNDERSTANDING YOUR INSTRUMENT PANEL The primary control for the rear blower is on the front climate control unit located on the instrument panel. When the front control is in any position other than rear, the front control operates all the rear functions. The rear airflow modes will mirror the front unit opera- tion.
Page 323
UNDERSTANDING YOUR INSTRUMENT PANEL 321 2. Rear Blower Control — If Equipped 4. Rear Temperature Control — If Equipped Use this control to regulate the amount of air forced Provides temperature control for the rear cabin. Turn left through the rear system in any mode you select. The rear for cooler or right for warmer temperature settings in the blower speed increases as you move the control to the rear cabin.
Page 324
322 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Front Defrost Mode NOTE: • You can turn off the heated mirror feature at anytime Air is directed through the windshield and side window demist outlets. Use DEFROST mode with by pressing the rear window defroster switch a second maximum blower and temperature settings for best time.
Page 325
UNDERSTANDING YOUR INSTRUMENT PANEL 323 NOTE: CAUTION! (Continued) • If the RECIRCULATION button is pressed when the • Do not use scrapers, sharp instruments, or abra- system is in MIX, DEFROST, or FLOOR mode the sive window cleaners on the interior surface of the RECIRCULATION LED indicator will flash 3 times to window.
324 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Air Conditioning (A/C) Button NOTE: There is a difference in temperature (in any Press and release to change the current setting. conditions other than full cold or full hot), between the The indicator illuminates when ON. upper and lower outlets for added comfort.
Page 327
UNDERSTANDING YOUR INSTRUMENT PANEL 325 The rear blower and temperature controls for the rear Rear Blower Control seat passengers are located in the headliner, near the The primary control for the rear blower is on the front center of the vehicle. climate control unit, located on the instrument panel.
Page 328
326 UNDERSTANDING YOUR INSTRUMENT PANEL When rear controls are locked by the front system, the CAUTION! lock symbol on the temperature knob is illuminated, and the rear overhead adjustments are inoperable. Interior air enters the Rear Manual Climate Control system through an intake grille, located in the right Rear Mode Control side trim panel behind the third row seats.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 Floor Mode The Three-Zone ATC System automatically maintains the Air comes from the floor outlets. interior comfort level desired by the driver and all passengers. The system automatically adjusts the air temperature, the airflow volume, amount of outside air Automatic Temperature Control (ATC) —...
Page 330
328 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Air Conditioning (A/C) Button 6. Right Front Seat Occupant Temperature Display Press and release to change the current Air Conditioning This display shows the temperature setting for the right (A/C) setting, the indicator illuminates when A/C is ON. front seat occupant.
Page 331
UNDERSTANDING YOUR INSTRUMENT PANEL 329 10. Rear Control Button 14. Blower Control Provides toggle operation between front control screen There are seven blower speeds, the blower speed in- and rear control screen. Push the button to activate the creases as you move the control to the right from the rear climate control screen and allow the front seat lowest blower setting.
Page 332
330 UNDERSTANDING YOUR INSTRUMENT PANEL 18. SYNC Button 3. When the system is set up for your comfort level, it is Press and release to control the temperature setting for not necessary to change the settings. You will experience both zones from the driver temperature control. the greatest efficiency by simply allowing the system to function automatically.
Page 333
UNDERSTANDING YOUR INSTRUMENT PANEL 331 To provide you with maximum comfort in the automatic There are seven fixed blower speeds. mode, during cold start-ups, the blower fan will remain Use the outer dial control to regulate on low until the engine warms up. The fan will engage the amount of air forced through the immediately if the DEFROST mode is selected, or by system in any mode you select.
Page 334
332 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Mode Floor Mode Air is directed through the outlets in the instrument Air comes from the floor outlets. A slight amount of panel. These outlets can be adjusted for direction, air is directed through the defrost and side window and turned on or off to control airflow.
Page 335
UNDERSTANDING YOUR INSTRUMENT PANEL 333 Air Conditioning (A/C) Recirculation Control The Air Conditioning (A/C) button allows the operator When outside air contains smoke, odors, or to manually activate or deactivate the air conditioning high humidity, or if rapid cooling is desired, system.
Page 336
334 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Automatic Temperature Control (ATC) — The rear ATC system is located in the headliner, near the If Equipped center of the vehicle. The rear ATC system has floor air outlets at the rear of the right side sliding door, and overhead outlets at each outboard rear seating position.
Page 337
UNDERSTANDING YOUR INSTRUMENT PANEL 335 1. Press the Rear Temperature Lock button on the front NOTE: • It is not necessary to move the temperature settings for ATC panel. This turns off the Rear Temperature Lock icon in the rear temperature knob. cold or hot vehicles.
Page 338
336 UNDERSTANDING YOUR INSTRUMENT PANEL When rear controls are locked by the front system, the CAUTION! Rear Temperature Lock symbol on the temperature knob is illuminated and any rear overhead adjustments are Interior air enters the Rear Automatic Temperature ignored. Control System through an intake grille, located in the right side trim panel behind the third row seats.
UNDERSTANDING YOUR INSTRUMENT PANEL 337 Bi-Level Mode Summer Operation Air comes from both the headliner outlets and the The engine cooling system in air conditioned vehicles floor outlets. must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect NOTE: In many temperature positions, the BI-LEVEL against engine overheating.
338 UNDERSTANDING YOUR INSTRUMENT PANEL Vacation/Storage Outside Air Intake Before you store your vehicle, or keep it out of service Make sure the air intake, located directly in front of the (i.e., vacation) for two weeks or more, run the air windshield, is free of obstructions such as leaves.
UNDERSTANDING YOUR INSTRUMENT PANEL 339 Operating Tips A/C Air Filter— If Equipped On vehicles equipped with Automatic Temperature Con- trol (ATC), the climate control system filters out dust and pollen from the air. Refer to “Air Conditioning” in “Maintaining Your Vehicle” for filter replacement instructions.
STARTING AND OPERATING 345 STARTING PROCEDURES Normal Starting Before starting your vehicle, adjust your seat, adjust the 1. Do not press the accelerator. inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat 2.
346 STARTING AND OPERATING Extreme Cold Weather (Below 20°F or –7°C) WARNING! (Continued) Follow the same instructions in the “Normal Starting” • Do not attempt to push or tow your vehicle to get procedure. it started. Vehicles equipped with an automatic To ensure reliable starting at these temperatures, use of transmission cannot be started this way.
STARTING AND OPERATING 347 ENGINE BLOCK HEATER — IF EQUIPPED CAUTION! The engine block heater warms the engine, and permits To prevent damage to the starter, DO NOT crank the quicker starts in cold weather. Connect the cord to a engine for more than 15–second intervals at one time.
348 STARTING AND OPERATING AUTOMATIC TRANSMISSION WARNING! CAUTION! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle Damage to the transmission may occur if the follow- speed. If your foot is not firmly on the brake pedal, ing precautions are not observed: the vehicle could accelerate quickly forward or in •...
STARTING AND OPERATING 349 This system prevents the key fob from being removed Fuel Economy (ECON) Mode unless the shift lever is in PARK. It also prevents moving The Fuel Economy (ECON) mode can improve the vehi- the shift lever out of PARK, unless the key fob is in the cle’s overall fuel economy during normal driving condi- ACC/ON position, and the brake pedal is pressed.
350 STARTING AND OPERATING When the Fuel Economy (ECON) Mode is engaged, the Six-Speed Automatic Transmission vehicle control systems will be able to change the follow- NOTE: Under extreme cold temperatures (-10°F (-23°C) ing: and when in DRIVE, transmission operation may be •...
STARTING AND OPERATING 351 The transmission shift lever has only PARK, REVERSE, NEUTRAL, and DRIVE shift positions. Manual down- shifts can be made using the Electronic Range Select (ERS) shift control (refer to “Electronic Range Select (ERS) Operation” in this section). Moving the lever to the left or right (–/ +) while in the DRIVE position will select the highest available transmission gear, and will display that gear in the instrument cluster as 6, 5, 4, 3, 2, 1.
Page 354
352 STARTING AND OPERATING When parking on a flat surface, place the shift lever in the WARNING! (Continued) PARK position first, and then apply the parking brake. • Unintended movement of a vehicle could injure When parking on a hill, it is important to set the parking those in and near the vehicle.
Page 355
STARTING AND OPERATING 353 The following indicators should be used to ensure that REVERSE you have placed the shift lever into the PARK position: This range is for moving the vehicle backward. Shift into REVERSE only after the vehicle has come to a complete •...
Page 356
354 STARTING AND OPERATING DRIVE never shift above third gear, but can shift down into This range should be used for most city and highway second or first gear automatically, when needed. driving. It provides the smoothest upshifts, downshifts, Switching from ERS to DRIVE can be done at any vehicle and best fuel economy.
STARTING AND OPERATING 355 NOTE: To select the proper gear position for maximum 2. Shift into PARK. deceleration (engine braking), simply press and hold the 3. Turn the ignition switch to the LOCK position. shift lever to the left (-). The transmission will shift to the range from which the vehicle can best be slowed down.
356 STARTING AND OPERATING 2. Slow down if the road has standing water or puddles. WARNING! 3. Replace the tires when tread wear indicators first Rapid acceleration on slippery surfaces is dangerous. become visible. Unequal traction can cause sudden pulling of the 4.
STARTING AND OPERATING 357 Flowing/Rising Water CAUTION! • Always check the depth of the standing water WARNING! before driving through it. Never drive through Do not drive on or across a road or path where water standing water that is deeper than the bottom of is flowing and/or rising (as in storm run-off).
Page 360
358 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Driving through standing water may cause dam- • Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph ways inspect your vehicle’s fluids (i.e., engine oil, (8 km/h) when driving through standing water.
STARTING AND OPERATING 359 • Upon initial start-up in cold weather, the power steer- POWER STEERING The standard power steering system will give you good ing pump may make noise for a short amount of time. vehicle response and increased ease of maneuverability This is due to the cold, thick fluid in the steering in tight spaces.
360 STARTING AND OPERATING Power Steering Fluid Check WARNING! Checking the power steering fluid level at a defined service interval is not required. The fluid should only be Fluid level should be checked on a level surface and checked if a leak is suspected, abnormal noises are with the engine off to prevent injury from moving apparent, and/or the system is not functioning as antici- parts and to ensure accurate fluid level reading.
Page 363
STARTING AND OPERATING 361 The foot operated parking brake is positioned below the When the parking brake is applied with the ignition lower left corner of the instrument panel. To apply the switch in the ON position, the “Brake Warning Light” in park brake, firmly push the park brake pedal fully.
Page 364
362 STARTING AND OPERATING difficult to move the shift lever out of PARK. The parking WARNING! (Continued) brake should always be applied whenever the driver is • Always fully apply the parking brake when leav- not in the vehicle. ing your vehicle, or it may roll and cause damage or injury.
STARTING AND OPERATING 363 • A slight drop or fall away of the brake pedal at the end ANTI-LOCK BRAKE SYSTEM (ABS) The Anti-Lock Brake System (ABS) provides increased of the stop vehicle stability and brake performance under most WARNING! braking conditions.
364 STARTING AND OPERATING If the “Anti-Lock Brake Warning Light” remains on or WARNING! (Continued) comes on while driving, it indicates that the anti-lock • The Anti-Lock Brake System cannot prevent colli- portion of the brake system is not functioning and that sions, including those resulting from excessive service is required.
STARTING AND OPERATING 365 ELECTRONIC BRAKE CONTROL SYSTEM will allow more engine torque to be applied to the wheel Your vehicle is equipped with an advanced electronic that is not spinning. This feature remains active even if brake control system that includes the Traction Control the ESC is in the “Partial Off”...
366 STARTING AND OPERATING during the stopping sequence. Do not reduce brake pedal WARNING! (Continued) pressure unless braking is no longer desired. Once the • The TCS cannot prevent collisions, including brake pedal is released, the BAS is deactivated. those resulting from excessive speed in turns, or hydroplaning.
STARTING AND OPERATING 367 Electronic Stability Control (ESC) WARNING! The Electronic Stability Control (ESC) enhances direc- • The Electronic Stability Control (ESC) cannot pre- tional control and stability of the vehicle under various driving conditions. ESC corrects for over/under steering vent the natural laws of physics from acting on the of the vehicle by applying the brake of the appropriate vehicle, nor can it increase the traction afforded by...
Page 370
368 STARTING AND OPERATING ESC On again, momentarily press the “ESC Off” switch. This will This mode is the normal operating mode for ESC on restore the normal “ESC On” mode of operation. two-wheel drive vehicles. Whenever the vehicle is NOTE: To improve the vehicle’s traction when driving started, the ESC system will be in this mode.
Page 371
STARTING AND OPERATING 369 malfunction has been detected in the ESC system. If this NOTE: • The “ESC Activation/Malfunction Indicator Light” light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at and the “ESC OFF Indicator Light” come on momen- speeds greater than 30 mph (48 km/h), see your autho- tarily each time the ignition switch is turned ON.
370 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 373
STARTING AND OPERATING 371 • High flotation tire sizing is based on U.S. design Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designa- standards and it begins with the tire diameter molded tion.
Page 374
372 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
STARTING AND OPERATING 373 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
374 STARTING AND OPERATING Tire Terminology and Definitions Term Definition B-Pillar The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold Tire Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
STARTING AND OPERATING 375 Tire Loading And Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard Tire Placard Location...
Page 378
376 STARTING AND OPERATING NOTE: Under a maximum loaded vehicle condition, This placard tells you important information about gross axle weight ratings (GAWRs) for the front and rear the: axles must not be exceeded. For further information on 1) number of people that can be carried in the vehicle GAWRs, vehicle loading, and trailer towing, refer to 2) total weight your vehicle can carry “Vehicle Loading”...
Page 379
STARTING AND OPERATING 377 Steps For Determining Correct Load Limit 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely 1. Locate the statement “The combined weight of occu- exceed the available cargo and luggage load capacity pants and cargo should never exceed XXX lbs or XXX kg”...
STARTING AND OPERATING 379 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
380 STARTING AND OPERATING Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side “B” Pillar. hicle to the other can cause the vehicle to drift to The tire pressure should be checked and adjusted, and the right or left.
STARTING AND OPERATING 381 is defined as the tire pressure after the vehicle has not Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) been driven for at least three hours, or driven less than during operation. Do not reduce this normal pressure 1 mile (1.6 km) after a three-hour period.
382 STARTING AND OPERATING Cuts and punctures in radial tires are repairable only in WARNING! the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs. High-speed driving, with your vehicle at or above maximum load, is dangerous. The added strain on Spare Tire Matching Original Equipped Tire and your tires could cause them to fail.
STARTING AND OPERATING 383 If your vehicle is not equipped with an original equip- Compact Spare Tire – If Equipped ment tire and wheel as a spare, a non-matching tempo- The compact spare is for temporary emergency use only. rary emergency use spare may be equipped with your You can identify if your vehicle is equipped with a vehicle.
384 STARTING AND OPERATING your original equipment tire, replace (or repair) the WARNING! original equipment tire and reinstall on the vehicle at the first opportunity. Compact spares are for temporary emergency use only. With these spares, do not drive more than Limited-Use Spare –...
STARTING AND OPERATING 385 Tire Spinning WARNING! When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h), Limited-use spares are for emergency use only. In- or for more than 30 seconds continuously, without stop- stallation of this limited-use spare tire affects vehicle ping.
386 STARTING AND OPERATING Tread Wear Indicators These indicators are molded into the bottom of the tread Tread wear indicators are in the original-equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm).
STARTING AND OPERATING 387 Keep dismounted tires in a cool, dry place with as little WARNING! exposure to light as possible. Protect tires from contact • Do not use a tire, wheel size or rating other than with oil, grease and gasoline. that specified for your vehicle.
388 STARTING AND OPERATING WARNING! (Continued) CAUTION! • Failure to equip your vehicle with tires having To avoid damage to your vehicle or tires, observe the adequate speed capability can result in sudden tire following precautions: failure and loss of vehicle control. •...
STARTING AND OPERATING 389 SNOW TIRES CAUTION! (Continued) Some areas of the country require the use of snow tires • Install chains on the front wheels as tightly as during the winter. All season tires satisfy this require- possible and then retighten after driving about ment can be identified by the M+S designation on the tire 0.5 mile (0.8 km).
390 STARTING AND OPERATING poorer than that of non-studded tires. Some states pro- The suggested rotation method is the “rearward cross” hibit studded tires; therefore, local laws should be shown in the following diagram. This rotation pattern checked before using these tire types. does not apply to some directional tires that must not be reversed.
STARTING AND OPERATING 391 TIRE PRESSURE MONITOR SYSTEM (TPMS) The TPMS will warn the driver of a low tire pressure if The TPMS will warn the driver of a low tire pressure the tire pressure falls below the low pressure warning based on the cold inflation tire pressure requirements threshold for any reason, including low temperature found on the tire placard located on the driver’s-side...
Page 394
392 STARTING AND OPERATING For example, your vehicle may have a recommended CAUTION! cold (parked for more than three hours) tire pressure of • The TPMS has been optimized for the original 35 psi (241 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 30 psi (207 kPa), a equipment tires and wheels.
STARTING AND OPERATING 393 • Seasonal temperature changes will affect tire pressure, NOTE: • The TPMS is not intended to replace normal tire care and the TPMS will monitor the actual tire pressure in and maintenance, or to provide warning of a tire the tire.
Page 396
394 STARTING AND OPERATING Tire Pressure Monitoring Low Tire Pressure The “Tire Pressure Monitoring Telltale Light” will flash Warnings on and off for 75 seconds, and remain on solid when a The “Tire Pressure Monitoring Telltale Light” system fault is detected. The system fault will also sound will illuminate in the instrument cluster, a a chime.
STARTING AND OPERATING 395 Vehicles with Compact Spare 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare 1. The compact spare tire (if equipped) does not have a tire, the TPMS will automatically update, and the “Tire TPMS sensor.
Page 398
396 STARTING AND OPERATING The Premium TPMS consists of the following compo- nents: • Receiver Module • Four TPMS Sensors • Various TPMS messages, which display in the Elec- tronic Vehicle Information Center (EVIC), and graph- ics displaying tire pressures •...
Page 399
STARTING AND OPERATING 397 the “Tire Pressure Monitoring Telltale Light” will extin- guish once the updated tire pressure(s) have been re- ceived. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information.
Page 400
398 STARTING AND OPERATING message will not be present, and a pressure value will be message is then followed by a graphic display with displayed instead of dashes. A system fault can occur by pressure values still shown. This indicates that the pres- any of the following scenarios: sure values are still being received from the TPM sensors but they may not be in the correct vehicle position.
Page 401
STARTING AND OPERATING 399 3. After driving the vehicle for up to 20 minutes above and the graphic in the EVIC will display a new pressure 15 mph (24 km/h), the “Tire Pressure Monitoring Telltale value instead of dashes (- -), as long no tire pressure is Light”...
400 STARTING AND OPERATING The tire pressure sensors are regulated under one of the required. Poor quality gasoline can cause problems such following licenses: as hard starting, stalling, and hesitations. If you experi- ence these symptoms, try another brand of gasoline before considering service for the vehicle.
STARTING AND OPERATING 401 The manufacturer supports the use of reformulated gaso- Problems that result from using gasoline containing line. Properly blended reformulated gasoline will pro- Methanol or gasoline containing more than 10% Ethanol vide excellent performance and durability of engine and are not the responsibility of the manufacturer and may fuel system components.
402 STARTING AND OPERATING To fix a Non-FFV vehicle inadvertently fueled once with therefore, you should ask your gasoline retailer whether E-85 perform the following: the gasoline contains MMT. It is even more important to look for gasoline without MMT in Canada, because MMT •...
STARTING AND OPERATING 403 Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers, is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentra- performance: tions of methanol.
404 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper WARNING! maintenance. Have the exhaust system inspected Carbon monoxide (CO) in exhaust gases is deadly. every time the vehicle is raised. Have any abnor- Follow the precautions below to prevent carbon mal conditions repaired promptly.
Page 407
STARTING AND OPERATING 405 the other sections of this manual for information on CAUTION! features that are common between Flexible Fuel and gasoline-only powered vehicles. Only vehicles with the E-85 fuel filler door label can operate on E-85. E-85 Fuel Cap E-85 Badge...
406 STARTING AND OPERATING Ethanol Fuel (E-85) When you do switch fuel types it is recommended that: E-85 is a mixture of approximately 85% fuel ethanol and • you do not switch when the fuel gauge indicates less 15% unleaded gasoline. than 1/4 full •...
STARTING AND OPERATING 407 • Some additives used in regular gasoline are not fully Starting compatible with E-85 and may form deposits in your The characteristics of E-85 fuel make it unsuitable for use engine. To eliminate driveability issues that may be when ambient temperatures fall below 0°F (-18°C).
408 STARTING AND OPERATING Replacement Parts ADDING FUEL Many components in your Flexible Fuel Vehicle (FFV) are Fuel Filler Cap (Gas Cap) designed to be compatible with ethanol. Always be sure The gas cap is located behind the fuel filler door on the that your vehicle is serviced with correct ethanol com- left side of the vehicle.
Page 411
STARTING AND OPERATING 409 NOTE: The driver’s side sliding door cannot be opened WARNING! while the fuel door is open. This feature operates only • Never have any smoking materials lit in or near when the sliding door is fully closed prior to opening the fuel door.
410 STARTING AND OPERATING • If the gas cap is not tightened properly, the MIL may VEHICLE LOADING come on. Be sure the gas cap is tightened every time As required by National Highway Traffic Safety Admin- the vehicle is refueled. istration regulations, your vehicle has a certification label affixed to the driver’s side door or B-Pillar.
Page 413
STARTING AND OPERATING 411 • Vehicle Identification Number (VIN) WARNING! • Type of Vehicle Because the front wheels drive and steer the vehicle, • Month, Day and Hour of Manufacture (MDH) it is important that you do not exceed the maximum front or rear GAWR.
Page 414
412 STARTING AND OPERATING Curb Weight Figure out the weight on the front and rear of the vehicle The curb weight of a vehicle is defined as the total weight separately. It is important that you distribute the load of the vehicle with all fluids, including vehicle fuel, at full evenly over the front and rear axles.
STARTING AND OPERATING 413 Common Towing Definitions CAUTION! The following trailer towing-related definitions will as- sist you in understanding the following information: Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, Gross Vehicle Weight Rating (GVWR) parts on your vehicle can break, or it can change the The GVWR is the total allowable weight of your vehicle.
Page 416
414 STARTING AND OPERATING Gross Combination Weight Rating (GCWR) WARNING! The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination. It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition NOTE: The GCWR rating includes a 150 lbs (68 kg) can result if either rating is exceeded.
Page 417
STARTING AND OPERATING 415 Trailer Sway Control Weight-Distributing Hitch The trailer sway control is a telescoping link that can be A weight-distributing system works by applying lever- installed between the hitch receiver and the trailer tongue age through spring (load) bars. They are typically used that typically provides adjustable friction associated with for heavier loads to distribute trailer tongue weight to the the telescoping motion to dampen any unwanted trailer...
Page 418
416 STARTING AND OPERATING WARNING! • An improperly adjusted weight-distributing hitch system may reduce handling, stability, braking performance, and could result in a collision. • Weight-distributing hitch systems may not be compatible with surge brake couplers. Consult with an authorized hitch and trailer manufacturer or a reputable authorized Recreational Vehicle dealer for additional information.
Page 419
STARTING AND OPERATING 417 With Weight-Distributing Hitch (Correct) Improper Adjustment of Weight-Distributing Hitch (Incorrect)
Page 420
418 STARTING AND OPERATING Trailer Hitch Classification TRAILER HITCH CLASSIFICATIONS Your vehicle may be factory-equipped for safe towing of Max. GTW (Gross Trailer Class trailers weighing over 2,000 lbs (907 kg) with the optional Wt.) Trailer Tow Prep Package. See an authorized dealer for Class I - Light Duty 2,000 lbs (907 kg) package content.
Page 421
STARTING AND OPERATING 419 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. GCWR (Gross Com- Max. GTW Engine/Transmission Frontal Area Max. Tongue Wt. bined Wt. Rating) (Gross Trailer Wt.) Up to 2 persons &...
Page 422
420 STARTING AND OPERATING GCWR (Gross Com- Max. GTW Engine/Transmission Frontal Area Max. Tongue Wt. bined Wt. Rating) (Gross Trailer Wt.) Up to 2 persons & 8,750 lbs (3 969 kg) 40 sq ft (3.72 sq m) Luggage 3,600 lbs 360 lbs (163 kg) (1 633 kg)* 3 to 5 persons &...
Page 423
STARTING AND OPERATING 421 which will cause loss of control of the vehicle and trailer. Consider the following items when computing the Failure to load trailers heavier in front is the cause of weight on the rear axle of the vehicle: many trailer collisions.
Page 424
422 STARTING AND OPERATING Towing Requirements WARNING! To promote proper break-in of your new vehicle drive- train components, the following guidelines are recom- Improper towing can lead to a injury collision. Fol- mended: low these guidelines to make your trailer towing as safe as possible: CAUTION! •...
Page 425
STARTING AND OPERATING 423 WARNING! (Continued) WARNING! (Continued) • Safety chains must always be used between your 3. GAWR vehicle and trailer. Always connect the chains to 4. Trailer tongue weight rating for that trailer hitch. the frame or hook retainers of the vehicle hitch. (This requirement may limit the ability to always Cross the chains under the trailer tongue and achieve the 10% to 15% range of trailer tongue weight...
Page 426
424 STARTING AND OPERATING • Check for signs of tire wear or visible tire damage • An electronically actuated trailer brake controller is before towing a trailer. Refer to “Tires – General required when towing a trailer with electronically Information” in “Starting and Operating” for the actuated brakes.
Page 427
STARTING AND OPERATING 425 Towing Requirements – Trailer Lights and Wiring WARNING! Whenever you pull a trailer, regardless of the trailer size, • Do not connect trailer brakes to your vehicle’s stop lights and turn signals on the trailer are required for motoring safety.
Page 428
426 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following four-pin connector and seven-pin connector illustrations. Seven-Pin Connector 1 — Battery 5 — Ground 2 —...
STARTING AND OPERATING 427 Towing Tips NOTE: • Check the automatic transmission fluid level before Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy towing. traffic. • The transmission is sealed and requires an authorized Automatic Transmission dealer to check the transmission fluid.
428 STARTING AND OPERATING Cooling System RECREATIONAL TOWING To reduce potential for engine and transmission over- (BEHIND MOTORHOME, ETC.) heating, take the following actions: CAUTION! • City Driving When stopped for short periods of time, shift the trans- Towing this vehicle behind another vehicle (flat- mission into NEUTRAL but do not increase engine idle towing with all four wheels on the ground) is not speed.
430 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the center of the instrument panel above the radio. potential for overheating by taking the appropriate ac- tion.
WHAT TO DO IN EMERGENCIES 431 JACKING AND TIRE CHANGING CAUTION! WARNING! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull • Do not attempt to change a tire on the side of the over and stop the vehicle.
432 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas.
WHAT TO DO IN EMERGENCIES 433 Spare Tire Removal NOTE: The base console, if equipped, must be removed The spare tire is stowed inside a protective cover located to raise and lower the spare tire. Refer to “Console under the center of the vehicle between the front doors by Features”...
434 WHAT TO DO IN EMERGENCIES NOTE: Passengers should not remain in the vehicle WARNING! when the vehicle is being jacked. Do not attempt to change a tire on the side of the Jacking Instructions vehicle close to moving traffic, pull far enough off the road to avoid being hit when operating the jack WARNING! or changing the wheel.
Page 437
WHAT TO DO IN EMERGENCIES 435 WARNING! (Continued) • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack. Jack Warning Label • Do not get under the vehicle when it is on a jack. •...
Page 438
436 WHAT TO DO IN EMERGENCIES configuration in tool graphics. Rotate the nut to the left CAUTION! until the winch mechanism stops turning freely. This will allow enough slack in the cable to allow you to pull the The winch mechanism is designed for use with the spare tire out from under the vehicle.
Page 439
WHAT TO DO IN EMERGENCIES 437 WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
Page 440
438 WHAT TO DO IN EMERGENCIES NOTE: If either front tire is flat, it may be necessary to 4. When the compact spare tire/cover assembly is clear jack up the vehicle to remove the compact spare tire/ of the vehicle, stand the tire/cover assembly upright and cover assembly from under the vehicle.
Page 441
WHAT TO DO IN EMERGENCIES 439 5. There are two jack engagement locations on each side of the vehicle body. These locations are on the sill flange of the vehicle body. NOTE: • Rear jack locations are between a pair of down-facing tabs on the sill flange of the vehicle side body.
Page 442
440 WHAT TO DO IN EMERGENCIES 6. Place the wrench on the jack screw and turn to the 8. Remove the wheel lug nuts, for vehicles with wheel right until the jack head is properly engaged in the covers, remove the cover from the wheel by hand. Do not described location.
WHAT TO DO IN EMERGENCIES 441 11. Finish tightening the lug nuts. Push down on the deflated tire in the spare tire location. Have the full- wrench while tightening for increased leverage. Alternate sized tire repaired or replaced, as soon as possible. lug nuts until each nut has been tightened twice.
442 WHAT TO DO IN EMERGENCIES should first be firmly seated against the wheel. The nuts WARNING! should then be tightened to recommended torque. Tighten the nuts to final torque in increments. Progress A loose compact spare tire/cover assembly, thrown around the bolt circle, tightening the nut opposite to the forward in a collision or hard stop could endanger nut just previously tightened until final torque is...
Page 445
WHAT TO DO IN EMERGENCIES 443 3. Turn the compact spare tire so that the valve stem is WARNING! down, and place the tire into the spare tire/cover assem- bly. Slide the wheel spacer through the center of the Verify that both retainer tabs of the wheel spacer wheel and spare tire/cover assembly, so that the two have been properly extended through the center of retainer tabs snap out and engage the spare tire cover on...
444 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! The winch mechanism is designed specifically to Do not use a portable battery booster pack or any stow a compact spare tire only. Do not attempt to use other booster source with a system voltage greater the winch to stow the full size flat tire, or any other than 12 Volts or damage to the battery, starter motor, full-size tire.
WHAT TO DO IN EMERGENCIES 445 Preparations For Jump-Start WARNING! The battery in your vehicle is located on the left side of • Take care to avoid the radiator cooling fan when- the engine compartment. ever the hood is raised. It can start anytime the ignition switch is on.
446 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park CAUTION! the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. Failure to follow these procedures could result in damage to the charging system of the booster vehicle WARNING! or the discharged vehicle.
Page 449
WHAT TO DO IN EMERGENCIES 447 8. Disconnect the opposite end of the positive (+) jumper WARNING! cable from the positive (+) post of the booster battery. Do not connect the cable to the negative post (-) of the 9. Disconnect the positive (+) end of the jumper cable discharged battery.
448 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE NOTE: To improve the vehicle’s traction when starting If your vehicle becomes stuck in mud, sand or snow, it off in deep snow, sand or gravel, it may be desirable to can often be moved by a rocking motion.
WHAT TO DO IN EMERGENCIES 449 2. Remove the shift lever override access cover located WARNING! near the top right of the shift lever in the instrument panel. Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires.
450 WHAT TO DO IN EMERGENCIES 5. Using a small screwdriver or similar small, push and 7. The vehicle may then be started in the NEUTRAL hold the override release lever forward. position. 6. Move the shift lever into the NEUTRAL position. 8.
Page 453
WHAT TO DO IN EMERGENCIES 451 If you must use the accessories (wipers, defrosters, etc.) The manufacturer recommends towing your vehicle with while being towed, the ignition must be in the ON/RUN all four wheels OFF the ground using a flatbed. If flatbed position, not the ACC position.
452 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! Towing faster than 25 mph (40 km/h) or farther than Failure to follow these towing methods could result 15 miles (24 km) with front wheels on the ground can in damage to the transmission. Such damage is not cause severe damage to the transmission.
456 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
MAINTAINING YOUR VEHICLE 457 “Electronic Vehicle Information Center (EVIC)” in ”Un- For states that require an Inspection and Mainte- derstanding Your Instrument Panel” for further informa- nance (I/M), this check verifies the “Malfunction tion. Tighten the gas cap until a clicking sound is heard. Indicator Light (MIL)”...
Page 460
458 MAINTAINING YOUR VEHICLE 2. If you crank or start the engine, you will have to start If your OBD II system is not ready, you should see your this test over. authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, 3.
MAINTAINING YOUR VEHICLE 459 REPLACEMENT PARTS WARNING! Use of genuine MOPAR parts for normal/scheduled maintenance and repairs is highly recommended to en- You can be badly injured working on or around a sure the designed performance. Damage or failures motor vehicle. Only do service work for which you caused by the use of non-MOPAR parts for maintenance have the knowledge and the proper equipment.
460 MAINTAINING YOUR VEHICLE Engine Oil CAUTION! • Failure to properly maintain your vehicle or per- Checking Oil Level To assure proper engine lubrication, the engine oil must form repairs and service when necessary could be maintained at the correct level. Check the oil level at result in more costly repairs, damage to other regular intervals, such as every fuel stop.
Page 463
MAINTAINING YOUR VEHICLE 461 American Petroleum Institute (API) Engine Oil CAUTION! Identification Symbol This symbol means that the oil has Overfilling or underfilling will cause oil aeration, or been certified by the American loss of oil pressure. This could damage your engine. Petroleum Institute (API).
462 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) Materials Added to Engine Oil SAE 5W-30 engine oil is recommended for all operating The manufacturer strongly recommends against the ad- temperatures. This engine oil improves low temperature dition of any additives (other than leak detection dyes) to starting and vehicle fuel economy.
MAINTAINING YOUR VEHICLE 463 Engine Oil Filter Selection WARNING! The manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality The air induction system (air cleaner, hoses, etc.) can of replacement filters varies considerably. Only high provide a measure of protection in the case of engine quality filters should be used to assure most efficient backfire.
464 MAINTAINING YOUR VEHICLE Exhaust System WARNING! The best protection against carbon monoxide entry into • Exhaust gases can injure or kill. They contain the vehicle body is a properly maintained engine exhaust system. carbon monoxide (CO), which is colorless and odorless.
Page 467
MAINTAINING YOUR VEHICLE 465 Under normal operating conditions, the catalytic con- CAUTION! verter will not require maintenance. However, it is im- • The catalytic converter requires the use of un- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst leaded fuel only.
466 MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter dam- WARNING! age: • Battery fluid is a corrosive acid solution and can • Do not shut off the engine or interrupt the ignition, burn or even blind you. Do not allow battery fluid when the transmission is in gear and the vehicle is in to contact your eyes, skin, or clothing.
MAINTAINING YOUR VEHICLE 467 Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner • It is essential when replacing the cables on the should be checked and serviced by an authorized dealer at the start of each warm season. This service should battery that the positive cable is attached to the include cleaning of the condenser fins and a system positive post and the negative cable is attached to...
Page 470
468 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling WARNING! R-134a air conditioning refrigerant is a hydrofluoro- • Use only refrigerants and compressor lubricants carbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. How- approved by the manufacturer for your air condi- ever, the manufacturer recommends that air conditioning tioning system.
Page 471
MAINTAINING YOUR VEHICLE 469 A/C Air Filter – If Equipped Refer to the “Maintenance Schedule” for the proper maintenance intervals. WARNING! Do not remove the A/C air filter while the blower is operating or personal injury may result. The A/C air filter is located in the fresh air inlet behind the glove box.
470 MAINTAINING YOUR VEHICLE hood latching components to ensure proper function. CAUTION! When performing other underhood services, the hood latch, release mechanism and safety catch should be The A/C air filter is labeled with an arrow to indicate cleaned and lubricated. airflow direction through the filter.
Page 473
MAINTAINING YOUR VEHICLE 471 Avoid using the wiper blades to remove frost or ice from WARNING! the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care NOTE: Life expectancy of wiper blades varies depend- must be exercised when filling or working around ing on geographical area and frequency of use.
472 MAINTAINING YOUR VEHICLE Cooling System rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of WARNING! the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden •...
Page 475
MAINTAINING YOUR VEHICLE 473 Cooling System – Drain, Flush, and Refill CAUTION! If the engine coolant (antifreeze) is dirty or contains a • Mixing of engine coolant (antifreeze) other than considerable amount of sediment, clean and flush with a specified Hybrid Organic Additive Technology reliable cooling system cleaner.
Page 476
474 MAINTAINING YOUR VEHICLE • Mix a minimum solution of 50% HOAT engine coolant Adding Coolant Your vehicle has been built with an improved engine and distilled water. Use higher concentrations (not to coolant (antifreeze) that allows extended maintenance exceed 70%) if temperatures below 34°F ( 37°C) are intervals.
Page 477
MAINTAINING YOUR VEHICLE 475 Cooling System Pressure Cap WARNING! (Continued) The cap must be fully tightened to prevent the loss of • Do not use a pressure cap other than the one engine coolant (antifreeze), and to ensure that engine specified for your vehicle.
Page 478
476 MAINTAINING YOUR VEHICLE engine cold, the level of the engine coolant (antifreeze) in normally a result of moisture from rain, snow, or high the coolant recovery bottle should be between the ranges humidity accumulating on the radiator and being vapor- indicated on the bottle.
MAINTAINING YOUR VEHICLE 477 • Maintain engine coolant (antifreeze) concentration at Brakes 50% HOAT engine coolant (antifreeze) (minimum) In order to assure brake system performance, all brake and distilled water for proper corrosion protection of system components should be inspected periodically. your engine, which contains aluminum components.
Page 480
478 MAINTAINING YOUR VEHICLE Master Cylinder – Brake Fluid Level Check Use only manufacturer’s recommended brake fluid. Re- The fluid level in the master cylinder should be checked fer to “Fluids, Lubricants, and Genuine Parts” in “Main- when performing underhood services, or immediately if taining Your Vehicle”...
MAINTAINING YOUR VEHICLE 479 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contami- moisture, use only new brake fluid or fluid that nate the brake fluid. Brake seal components could has been in a tightly closed container.
Page 482
480 MAINTAINING YOUR VEHICLE Selection of Lubricant CAUTION! It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- Using a transmission fluid other than the manufac- mance. Use only the manufacturer’s recommended trans- turer’s recommended fluid may cause deterioration mission fluid.
MAINTAINING YOUR VEHICLE 481 Appearance Care and Protection from Corrosion CAUTION! Protection of Body and Paint from Corrosion Do not use chemical flushes in your transmission as Vehicle body care requirements vary according to geo- the chemicals can damage your transmission compo- graphic locations and usage.
Page 484
482 MAINTAINING YOUR VEHICLE • Use a high quality cleaner wax, such as MOPAR The most common causes are: Cleaner Wax or equivalent to remove road film, stains • Road salt, dirt and moisture accumulation and to protect your paint finish. Take care never to •...
Page 485
MAINTAINING YOUR VEHICLE 483 • If a lot of driving is done on gravel roads, consider Special Care mud or stone shields behind each wheel. • If you drive on salted or dusty roads or if you drive • Use MOPAR near the ocean, hose off the undercarriage at least once Touch Up Paint or equivalent on a month.
Page 486
484 MAINTAINING YOUR VEHICLE Stain Repel Fabric Cleaning Procedure – Interior Care If Equipped Instrument Panel Surfaces Stain Repel seats may be cleaned in the following man- The instrument panel cover has a low glare surface, ner: which minimizes reflections in the windshield. Do not •...
Page 487
MAINTAINING YOUR VEHICLE 485 Your leather upholstery can be best preserved by regular Cleaning Headlights cleaning with a damp soft cloth. Small particles of dirt Your vehicle has plastic headlights that are lightweight can act as an abrasive and damage the leather upholstery and less susceptible to stone breakage than glass head- and should be removed promptly with a damp cloth.
486 MAINTAINING YOUR VEHICLE rear window equipped with electric defrosters or the Seat Belt Maintenance right rear quarter window equipped with the radio Do not bleach, dye or clean the seat belts with chemical antenna. Do not use scrapers or other sharp instruments solvents or abrasive cleaners.
MAINTAINING YOUR VEHICLE 487 Soak the liner in a mixture of medium hot tap water and section. This center contains cartridge fuses and mini- one teaspoon of mild liquid dish soap. Let soak for fuses. A label that identifies each component may be approximately 30 minutes.
Page 490
488 MAINTAINING YOUR VEHICLE FUSES/TIPM CAUTION! Cartridge • When installing the Totally Integrated Power Cavity Mini-Fuse Description Fuse Module cover, it is important to ensure the cover is 40 Amp — Power Folding Seat properly positioned and fully latched. Failure to Green do so may allow water to get into the Integrated 30 Amp...
Page 491
MAINTAINING YOUR VEHICLE 489 FUSES/TIPM FUSES/TIPM Cartridge Cartridge Cavity Mini-Fuse Description Cavity Mini-Fuse Description Fuse Fuse 40 Amp — Power Memory Seat 30 Amp — Front Blower Green – If Equipped Pink 40 Amp — Partial Zero Emis- 40 Amp —...
Page 492
490 MAINTAINING YOUR VEHICLE FUSES/TIPM FUSES/TIPM Cartridge Cartridge Cavity Mini-Fuse Description Cavity Mini-Fuse Description Fuse Fuse — 15 Amp Rear Center Brake — 20 Amp Front Heated Seat – Blue Lamp/Brake Switch Yellow If Equipped — — — — 20 Amp Rear Heated Seat –...
494 MAINTAINING YOUR VEHICLE seat. The power windows are fused by a 25 Amp circuit FUSES/TIPM breaker located under the instrument panel near the Cartridge Cavity Mini-Fuse Description steering column. If you experience temporary or perma- Fuse nent loss of these systems, see your authorized dealer for —...
MAINTAINING YOUR VEHICLE 495 system lubrication to minimize the possibility of com- All of the interior bulbs are glass wedge base or glass pressor damage when the system is started again. cartridge types. Aluminum base bulbs are not approved and should not be used for replacement. REPLACEMENT BULBS LIGHT BULBS –...
496 MAINTAINING YOUR VEHICLE BULB REPLACEMENT 5. Connect the wiring connector to bulb and slide red lock tab forward. Headlamps Front Park/Turn Signal Lamps 1. Raise the hood to access the rear of the headlamp housing. 1. Raise the hood to access the rear of the headlamp housing.
MAINTAINING YOUR VEHICLE 497 1. From behind the bumper fascia, or the access panel on Rear Tail, Stop, Turn Signal, Side Marker and the air dam, squeeze the two tabs on the side of the bulb Backup Lamps socket and pull straight out from the fog lamp. 1.
498 MAINTAINING YOUR VEHICLE NOTE: License Lamp • If a screwdriver is used, make sure a soft material is The license plate lamp is located under the tailgate light placed between the vehicle body and tool so not to bar and above the license plate. scratch the paint.
500 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part MOPAR Antifreeze/Coolant Five Year/100,000 Mile Formula HOAT Engine Coolant (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-30 Engine Oil, meeting the requirements of Engine Oil Chrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE 501 Chassis Component Fluid, Lubricant, or Genuine Part MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed Automatic Transmission ATF+4 product. MOPAR DOT 3 and SAE J1703 should be used or equivalent. If DOT 3 Brake Master Cylinder brake fluid is not available, then DOT 4 is acceptable.
Page 506
504 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE On Electronic Vehicle Information Center (EVIC) The Scheduled Maintenance services listed in this equipped vehicles, Oil Change Required will be dis- manual must be done at the times or mileages specified played in the EVIC and a single chime will sound, to protect your vehicle warranty and ensure the best indicating that an oil change is necessary.
Page 507
MAINTENANCE SCHEDULES 505 • Under no circumstances should oil change intervals At Each Stop For Fuel exceed 8,000 miles (13 000 km) or six months, which- • Check the engine oil level about five minutes after a ever comes first. fully warmed engine is shut OFF.
Page 508
506 MAINTENANCE SCHEDULES Once A Month At Each Oil Change • Check tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery and clean and tighten the terminals CAUTION! as required.
Page 509
MAINTENANCE SCHEDULES 507 8,000 Miles (13,000 km) or 16,000 Miles (26,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
508 MAINTENANCE SCHEDULES 24,000 Miles (39,000 km) or 32,000 Miles (52,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 511
MAINTENANCE SCHEDULES 509 40,000 Miles (65,000 km) or 48,000 Miles (78,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 512
510 MAINTENANCE SCHEDULES 56,000 Miles (91,000 km) or 64,000 Miles (104,000 km) or 48 Months Maintenance Service 42 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 513
MAINTENANCE SCHEDULES 511 72,000 Miles (117,000 km) or 80,000 Miles (130,000 km) or 60 Months Maintenance Service 54 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 514
512 MAINTENANCE SCHEDULES 88,000 Miles (143,000 km) or 96,000 Miles (156,000 km) or 72 Months Maintenance Service 66 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 515
MAINTENANCE SCHEDULES 513 104,000 Miles (169,000 km) or 112,000 Miles (182,000 km) or 84 Months Maintenance Service 78 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 516
514 MAINTENANCE SCHEDULES 120,000 Miles (195,000 km) or 128,000 Miles (208,000 km) or 96 Months Maintenance Service 90 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 517
MAINTENANCE SCHEDULES 515 136,000 Miles (221,000 km) or 144,000 Miles (234,000 km) or 108 Months Maintenance Service 102 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 518
516 MAINTENANCE SCHEDULES 152,000 Miles (247,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 152,000 miles (247 000 km). Odometer Reading Date Repair Order #...
Page 519
MAINTENANCE SCHEDULES 517 † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Suggestions For Obtaining Service For Your Vehicle......521 Speech Impaired (TDD/TTY) .
Page 522
520 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... 527 Department Of Transportation Uniform Tire Quality Grades ......527 ▫...
IF YOU NEED CONSUMER ASSISTANCE 521 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
522 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 solved with this process. Auburn Hills, MI 48321–8004 Phone: (800) 423–6343 •...
IF YOU NEED CONSUMER ASSISTANCE 523 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
524 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment WARRANTY INFORMATION when you purchased the vehicle. An authorized dealer See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle and market.
IF YOU NEED CONSUMER ASSISTANCE 525 If NHTSA receives similar complaints, it may open an In Canada investigation, and if it finds that a safety defect exists in If you believe that your vehicle has a safety defect, you a group of vehicles, it may order a recall and remedy should contact the Customer Service Department imme- campaign.
Page 528
526 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals • Owner’s Manuals These comprehensive Service Manuals provide the These Owner’s Manuals have been prepared with the information that students and professional technicians assistance of service and engineering specialists to need in diagnosing/troubleshooting, problem solving, acquaint you with specific Chrysler Group LLC ve- maintaining, servicing, and repairing Chrysler Group hicles.
Page 529
IF YOU NEED CONSUMER ASSISTANCE 527 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 530
528 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 549
INDEX 547 Traction Control Switch ....365 Transmitter, Remote Keyless Entry (RKE) ..19 Trailer Towing ......413 Transporting Pets .
Page 550
548 INDEX Vehicle Identification Number (VIN) ... . 6 Wheel and Wheel Trim Care ....483 Vehicle Loading .
Page 551
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 552
Chrysler Group LLC 11Y532-126-AA First Edition Printed in U.S.A.