Page 1
MU-60PZ10 Please read this owner’s manual carefully before MU-60PZ10A operating the Monitor. Retain it for future reference. MU-60PZ10B Record model number and serial number of the Monitor. MU-60PZ10K See the label attached on the back of the Monitor and quote this information to your dealer when you require service.
Page 2
FCC NOTICE • MU-60PZ10/A/B/K/S : A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
WARNINGS WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”...
SAFETY INSTRUCTIONS Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.
SAFETY INSTRUCTIONS (Continued from previous page) The openings should never be blocked by supporting structure, grounding of the lead- placing the product on a bed, sofa, rug, or in wire to an antenna discharge unit, size of other similar surface. This product should grounding conductors, location of antenna- not be placed in a built-in installation such discharge unit, connection to grounding...
Page 7
product through openings as they may 22. Safety Check touch dangerous voltage points or short-out Upon completion of any service or repairs to parts that could result in a fire or electric this product, ask the service technician to shock. Never spill liquid of any kind on the perform safety checks to determine that the product.
Front Panel Controls <Front Panel Controls> ON/OFF INPUT ON/OFF SELECT VOLUME Main power button Power standby indicator Illuminates red in standby INPUT mode Illuminates green SELECT VOLUME when the Monitor is turned INPUT SELECT button Sub power button VOLUME ( ) buttons Remote control sensor...
Remote Control Key Functions/Accessories - When using the remote control aim it at the remote control sensor on the Monitor. power on button power on system off sleep button (Refer to p .34) sleep mute mute button switches the sound on or off. number buttons video/pc menu...
Page 11
video/pc button on the remote system off button control Each press of this button changes the mode as shown below. No function VIDEO COMPONENT menu button enter button up/down buttons vol buttons twin picture button (Refer to p. 28) When pressed displays on screen.
(2000m) to get the best quality picture and sound. - Your MU-60PZ10/A/B/K/S (Monitor) can be installed on a wall as shown below, or on a desktop pedestal as shown on the next page. Wall mount and stands are optional, and are not supplied with the monitor.
Desktop Pedestal Installation INPUT ON/OFF SELECT VOLUME • The Monitor can be installed on a desk as shown above. (For further information, refer to the optional ‘Desktop Stand Installation and Setup Guide’.) • Speakers shown are optional, and shown for illustration only. ( Pedestal mount minimum 4inch 1.18inch...
VCR Setup - As shown below, when connecting the Monitor to a VCR, match the colors of AV input jacks on the Monitor with the output jacks on the VCR: Video = yellow, Audio (Left) = white, Audio (Right) = red. - If you have a mono VCR, connect the audio cable from the VCR to the AUDIO(L/MONO) input of the Plasma Monitor.
Cable TV Setup - After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. This monitor cannot display TV programming without a TV tuner or cable TV converter box. Speakers shown for illustration only.
External AV Source Setup - As shown below, when connecting the Monitor to an external source, match the colors of AV input jacks on the Monitor with the output jacks on the audio/video equipment: Video = yel- low, Audio (Left) = white, Audio (Right) = red. AUDIO (MONO) VIDEO...
DVD Setup How to connect a DVD (digital video disk player) • Connect DVD video inputs to Y, P of COMPONENT (480i/480p/720p/1080i) (DVD/DTV INPUT) and audio inputs to Audio jacks of AV INPUT. AUDIO (MONO) VIDEO AUDIO RGB-PC INPUT COMPONENT (480i/480p/720p/1080i) (VGA/SVGA/XGA/SXGA) AV INPUT (DVD/DTV INPUT)
DTV Setup - To watch digitally broadcast programs, purchase/connect a digital SET-TOP BOX. - You can select only the 16:9 picture format in DTV 720p/1080i mode. How to connect a user-supplied Digital Set-top Box • You can use either the Monitor’s COMPONENT (Y, P inputs or the single RGB-DTV INPUT for video connections, depending on your Set Top Box connectors.
PC Setup See your computer’s image on the monitor. How to connect Make the connections shown in the illustration below. • Set the computer video output to under SXGA (1280x1024) or lower resolution. (If the video output of the PC is not compatible with the Monitor, no picture will appear on the Monitor. See page 20.) •...
PC Mode Feature Check (Overview) - Select first, see page 11. - Make sure the PC and monitor are both turned on. - Use the monitor’s remote control to make adjustments. Press the menu button to show a menu on screen. menu Press the up( ) or down(...
PC Mode Adjustments Auto adjustment - Automatically adjusts picture position and eliminates any image shaking. Press the menu button and then press the up/down button to select the SPECIAL menu. Press the vol ( ) button. menu down Press the up/down buttons to select SCREEN and then press the vol ( ) button.
Page 23
Adjusting horizontal / vertical position manually - Only adjust in DTV or component 480p/720p/1080i. V-POSITION H-POSITION Press the menu button and then press the up/down button to select the SPECIAL menu. Press the vol ( ) button. menu down SCREEN Press the up/down buttons to select and then press the vol ( ) button.
PC Mode Adjustments Picture Phase Adjustments • If the picture isn’t clear after auto adjustment and especially if the characters are still trembling, then adjust the picture phase manually. • When watching PIP/TWIN PICTURE, the SCREEN menu option is not available. Press the menu button and then press the up/down button to select the SPECIAL...
Picture In Picture (PIP) function - PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. - Select RGB input source before pressing PIP. - This function works only in the following resolutions;...
Page 26
Picture In Picture (PIP) function Selecting the source input signal input select Press the input select button in PIP mode. • Each time you press input select button, you toggle between VIDEO COMPONENT VIDEO COMPONENT COMPONENT source only works in 480i mode. PIP INPUT VIDEO Moving the Sub (inset) picture...
Selecting PIP sound options - To select main or sub (inset) sound - This function only works with the following resolutions; 640x480, 800x600, 1024x768 (only in Vertical frequency 60 Hz) - To use this function, connect PC/DTV video output to RGB-PC INPUT/RGB-DTV INPUT and connect PC/DTV audio outputs to AUDIO INPUT.
Twin picture mode - As the name suggests, this mode splits the screen into 2, allowing 2 sources to be shown on the monitor screen at the same time. Each source is given half the screen. - Select input source. - This function works only in the following resolutions;...
Selecting a source for the Twin picture input select Press the input select button in TWIN PICTURE mode. • Each time you press input select button, you toggle between VIDEO COMPONENT VIDEO COMPONENT COMPONENT source only works in 480i input signal. PIP INPUT VIDEO...
Using the remote control Installing batteries • Open the battery compartment cover on the back of the remote control and insert the batteries with correct polarity, match “+” with “+”, and match “-” with “-”. • Install two 1.5V “AA” alkaline batteries. Don’t mix used batteries with new batteries.
Turning on the Monitor - When using the remote control, aim it at its sensor on the Monitor. Turning on the Monitor just after installation Connect power cord correctly. Press the main ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby mode.
Selecting language for the menus Press the menu button and then press the up/down button to select the SPECIAL menu. Press the vol ( ) button. menu down Press the up/down buttons to select SPECIAL LANGUAGE and then press the LANGUAGE LANGUAGE ˙–...
Checking features - Use the remote control to make adjustments. - Select VIDEO input source menu Press the menu button. Press the up/down buttons. • Each press will cycle through the menus shown below. down PICTURE CONTRAST BRIGHTNESS COLOR TINT SHARPNESS MOVE NEXT...
Setting Sleep Timer Sleep Timer turns the Monitor off after a preset time Press the sleep button to set sleep time. sleep Each time you press sleep button, the next preset setting time is changed as follows: SLEEP • To release sleep time setting, press the sleep or vol button repeatedly to select •...
Auto picture control Use APC to set the Monitor for the best picture appearance - APC is not available in RGB or PIP/TWIN PICTURE modes. APC (Auto Picture Control) Press the apc button. Press the apc or vol buttons to select your desired picture condition.
Adjusting picture appearance - PIP and Twin picture inset settings are not adjustable. Press the menu button and then press the up/down button to select the PICTURE menu. Press the vol ( ) button. menu down Example : Changing the contrast. PICTURE Press the up/downs button to select CONTRAST...
DRP (Digital Reality Picture) DRP improves image outlines in dark screens. - This function works in video, component 480i mode. Press the menu button and then press the up/down button to select the PICTURE menu. Press the vol ( ) button. menu down Press the up/down buttons to select...
Using the screen options - This function works only in the video mode. - Use this option if there are a trembling or instability of a video tape on screen during viewing the video. Press the menu button and then press the up/down button to select the SPECIAL menu.
Adjusting sound Manual setting Press the menu button and then press the up/down button to SOUND select the menu. Press the vol ( ) button. menu down Example : Adjustment treble SOUND Use the up/down buttons to select DASP TREBLE and then press the TREBLE TREBLE...
Auto Sound Control DASP (Digital Auto Sound Processing) • This function lets you enjoy the best sound without any manual adjustment because the Monitor automatically selects the appropriate audio tone levels based on the program content. easy sound Press the easy sound button. Press the easy sound or vol buttons to select a sound setup.
AVL (Auto Volume Leveler) This feature maintains an equal volume level; even if you change channels. Press the menu button and then press the up/down buttons SOUND to select the menu. Press the vol ( ) button. menu down Press the up/down buttons to select SOUND and then press the vol ( DASP...
Using Still function - This feature isn’t available for RGB input source. - Use with A/V or COMPONENT video inputs. Press the freeze button. freeze • The image displayed is frozen(still). • The sub picture is stilled in PIP or Twin picture mode. •...
Adjusting OSD Transparency To make the menus clear or opaque Press the menu button and then press the up/down button to SPECIAL select the menu. Press the vol ( ) button. menu down Press the up/down buttons to select SPECIAL TRANSPARENCY and then press the LANGUAGE...
Setting picture format - With the RGB (PC/DTV) input, you can select either 16:9 or 4:3 screen aspect ratios. - If 4:3 mode is used for a long time, the outline of the image may remain on the screen after you change to the 16:9 screen.
Maintenance - Early malfunction can be prevented. Careful and regular cleaning can extend the amount of time you will have with your new Monitor. Be sure to turn the power power off and unplug the power cord before you begin any cleaning. Cleaning the screen 1.
Troubleshooting check list • Check whether the Monitor is turned on. No picture & • Power cord inserted into wall outlet? No sound • Plug another product’s power cord into the wall outlet where the Monitor’s power cord was plugged in. •...