Related Manuals for HAMPTON BAY Colby
Summary of Contents for HAMPTON BAY Colby
- Page 1 731 242 Colby Quick-Install Ceiling Fan Owner’s Manual Colby Ventilador de Techo de Instalación Rápida de 1,32 Manual del Propietario...
-
Page 2: Table Of Contents
52” Colby Thank you for purchasing this Hampton Bay ceiling fan. This product has been manufactured with the highest standards of safety and quality. The finish Ceiling Fan by Hampton Bay of this fan is weather resistant, but over time will naturally weather and fade. -
Page 3: Safety Rules 1
READ AND SAVE THESE INSTRUCTIONS To avoid personal injury or damage to the fan and other items, To reduce the risk of electric shock, insure electricity be cautious when working around or cleaning the fan. has been turned off at the circuit breaker or fuse box before beginning. -
Page 4: Unpacking Your Fan
Unpack your fan and check the contents. You should have the following items: Mounting Hardware 1. Mounting Plate (inside canopy) 6. Extra Switch Cup Cover (1 hanger pin, 1 locking pin, 2. Canopy 7. Blades (5) 1 rubber gasket) 3. Ball/Downrod Assembly 8. -
Page 5: Tools Required
Figure 2 installation hanger bar as shown in Figure 4 MAY NOT BE ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED. CONSULT A (available at your Hampton Bay retailer). LICENSED ELECTRICIAN IF IN DOUBT. Installing Your Fan 3. -
Page 6: Hanging The Fan
Attaching the Blade Hanging the Fan Standard Ceiling Mounting Bracket 1. Loosen the 2 screws in the collar on the REMEMBER turn pow- top of the motor assembly er. Follow the steps below to hang your IMPORTANT - REMOVE THE RUBBER 2. -
Page 7: Close-To-Ceiling" Mounting
“Close-to-Ceiling” Mounting 4. Route the wires exiting the top of the fan motor through the canopy ring. Make sure 1. Remove the canopy ring from the canopy the slot openings are on top. Route the wires by turning the ring to the right until it through the canopy and then through the unlocks (Figure 6). - Page 8 Installing Fan to 6. Align the mounting holes with the holes in the motor and fasten, using the three the Outlet Box screws and lock-washers removed in step 4 (Figure 11). 7. Tighten the mounting screws securely. WHEN USING THE STANDARD BALL/DOWN- ROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING BRACKET MUST FAILURE TO PROPERLY INSTALL SET SCREWS...
- Page 9 1. Connect the two green fan ground wires lo- cated on the downrod and mounting plate ELECTRICAL DIAGRAMS ARE FOR REFERENCE to the household ground wire. When using ONLY. OPTIONAL USE OF ANY LIGHT KIT SHALL BE UL LISTED AND MARKED SUITABLE FOR Close-to-Ceiling mounting, there is only USE WITH THIS FAN.
- Page 10 Attaching the CLOSE-TO-CEILING MOUNTING Fan Blades 1. Carefully unhook the fan from the mount- ing bracket and align the locking slots of the ceiling canopy with the two screws in Your fan features revolutionary advancements the mounting plate. Push up to engage the for quick and easy blade installation slots and turn clockwise to lock in place.
-
Page 11: Blade Balancing
Blade Balancing molded plugs together (blue to black: white to white). Carefully tuck all wires back into the switch cup. All blades are grouped by weight. Because nat- ural woods vary in density, the fan may wobble 3. Align the three serrated head screws on the even though the blades are weight matched. - Page 12 AN EXTRA SWITCH CUP COVER IS INCLUDED YOUR WITHOUT THE LIGHT FIXTURE. WARNING: To reduce the risk of electri- cal shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 1. Remove and retain the three serrated head screws that secure the fixture to the bottom of the switch cup.
-
Page 13: Operating Your Fan 11
Turn on the power and check the operation of the fan. The pull chain controls the fan speeds as follows: 1 pull - High, 2 pulls - Medium, 3 pulls - Low and 4 pulls - Off Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans, and so on. -
Page 14: Care Of Your Fan
Troubleshooting Care of Your Fan Here are some suggestions to help you Problem Solution maintain your fan. Fan will not start Check main and branch circuit fuses or breakers 1. Because of the fan’s natural movement, Check line wire connections to the fan and switch wire connections in some connections may become loose. -
Page 15: Specifications 13
GROSS FAN SIZE SPEED VOLTS AMPS WATTS CUBE FEET WEIGHT WEIGHT 0.22 1595 20.5 22.4 52” 0.36 3727 1.77 High 0.54 5513 These are approximate measures. They do not include Amps and Wattage used by the light kit. Distributed by Home Depot U.S.A., Inc. 2455 Paces Ferry Rd. -
Page 16: Warranty Information
You must present a copy of the original Hampton Bay also warrants that all other fan parts, excluding any glass or acrylic blades, to be free purchase receipt to obtain warranty service.