Jonsered 2035 Instruction Manual
  1. Manuals
  2. Brands
  3. Jonsered Manuals
  4. Chainsaw
  5. 2035
  6. Instruction manual
Jonsered 2035 Instruction Manual

Jonsered 2035 Instruction Manual

Jonsered 2035 chain saw instruction manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Instruction Manual

Manuel d'instructions
Betriebsanweisung
Manual de instrucciones
English
Please read these instructions carefully make sure you understand them
before using this unit.
Français
Avant d'utiliser cet appareil, veuillez lire attentivement les instructions et
assurez--vous de les avoir comprises.
Deutsch
Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch.
Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen
verstanden haben.
Español
Lea atentamente las instrucciones y asegúrese de entenderlas antes de
utilizar esta unidad.
R
2035
530088158
12/19/01

Advertisement

Table of Contents
loading

Related Manuals for Jonsered 2035

Summary of Contents for Jonsered 2035

  • Page 1: Instruction Manual

    2035 Instruction Manual Manuel d’instructions Betriebsanweisung Manual de instrucciones English Please read these instructions carefully make sure you understand them before using this unit. Français Avant d’utiliser cet appareil, veuillez lire attentivement les instructions et assurez--vous de les avoir comprises.
  • Page 2 IDENTIFICATION (WHAT IS WHAT?) 1. Cylinder Cover 14. Saw Chain 2. Front Handle 15. Saw Bar 3. Front Handle Guard 16. Bumper Spike 4. Starter Cover 17. Chain Catcher 5. Chain Oil Tank 18. Clutch Cover 6. Starter Handle 19. Rear Hand Guard 7.
  • Page 3 Do not allow other people or animals teners securely tightened. to be near the chain saw when starting or S Use only Jonsered accessories and re- operating the chain saw. placement parts as recommended. S Do not handle or operate a chain saw...
  • Page 4 or work that could cause sparks. Allow en- gine to cool before refueling. S Mix and pour fuel in an outdoor area on bare ground; store fuel in a cool, dry, well venti- lated place; and use an approved, marked container for all fuel purposes.
  • Page 5 “in-line” with each other. The spread and “in-line” position of the hands provided by this design work together to give balance and resistance in controlling the pivot of the saw back toward the operator if kick- back occurs. Elbow locked Small Radius Tip Guide Bar Thumb on underside of...
  • Page 6 ASSEMBLY Protective gloves (not provided) should be S Slide the bar toward the rear of the saw as worn during assembly. far as possible. S Prepare the chain by checking the proper ATTACHING THE BUMPER direction. Without following the illustration SPIKE it is easy to place the chain on the saw the S Attach the bumper spike with the two...
  • Page 7 2-cycle air-cooled engine oil. recommend Jonsered brand oil mixed at a Only use Bar and Chain Oil for bar and chain ratio of 40:1 (2.5%). A 40:1 ratio is obtained lubrication. by mixing 5 liters of unleaded gasoline with Oil Cap 0.125 liter of oil.
  • Page 8 CHAIN BRAKE For cold weather starting, start the unit at full choke; allow the engine to warm up before WARNING squeezing the throttle trigger. : DO NOT ASSUME Do not cut material with the choke/fast idle THAT THE CHAIN BRAKE WILL PROTECT lever at the position.
  • Page 9 FELLING LARGE TREES S Practice cutting a few small logs using the following techniques to get the “feel” of us- (15 cm in diameter or larger) ing your saw before you begin a major The notch method is used to fell large trees. sawing operation.
  • Page 10 CUTTING A FALLEN TREE First cut on pressure side of log (BUCKING) Bucking is the term used for cutting a fallen tree to the desired log length. WARNING : Do not stand on the log Second cut being cut. Any portion can roll causing loss Second cut of footing and control.

  • Page 11: Bar Maintenance

    LIMBING PRUNING S Always limb a tree after it is cut down. Only WARNING then can limbing be done safely and prop- : Limit pruning to limbs erly. shoulder height or below. Do not cut if S Leave the larger limbs underneath the branches are higher than your shoulder.
  • Page 12 75501, USA, Tél. : +1 903 223 4100, declare under sole responsibility that the Jonsered model 2035 chain saw was assessed in accordance with Annex V of the DIRECTIVE and from serial numbers 2001--305(N or D)00001 and onwards, conforms to the provisions of the DIRECTIVE.
  • Page 13 TECHNICAL DATA SHEET 2035 Noise levels Engine 2035 Equivalent (see note 1) noise Cylinder volume, cm pressure level at operator ’s ear, Stroke, mm measured according to relevant Idle speed, rpm 3,000 international standards, dB(A) 90,6 Recommended max. Equivalent (see note 1) noise...

Table of Contents