Download  Print this page

Jonsered 2036 Instruction Manual

Jonsered chain saw instruction manual
Hide thumbs


Instruction Manual

Manuel d'instructions
Manual de instrucciones
Please read these instructions carefully make sure you understand them
before using this unit.
Avant d'utiliser cet appareil, veuillez lire attentivement les instructions et
assurez--vous de les avoir comprises.
Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch.
Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen
verstanden haben.
Lea atentamente las instrucciones y asegúrese de entenderlas antes de
utilizar esta unidad.



  Also See for Jonsered 2036

  Related Manuals for Jonsered 2036

  Summary of Contents for Jonsered 2036

  • Page 1: Instruction Manual

    2036/2040 Instruction Manual Manuel d’instructions Betriebsanweisung Manual de instrucciones English Please read these instructions carefully make sure you understand them before using this unit. Français Avant d’utiliser cet appareil, veuillez lire attentivement les instructions et assurez--vous de les avoir comprises.
  • Page 2: Identification Of Symbols

    IDENTIFICATION (WHAT IS WHAT?) 1. Cylinder Cover 13. Bar Tip Sprocket 2. Front Handle 14. Saw Chain 3. Front Handguard 15. Saw Bar 4. Starter Cover 16. Optional Bumper Spike 5. Chain Oil Tank 17. Chain Catcher 6. Starter Handle 18.
  • Page 3: Safety Rules

    SAFETY RULES S Carefully plan your sawing operation in ad- WARNING: vance. Do not start cutting until you have a Always disconnect clear work area, secure footing, and, if you spark plug wire and place wire where it can- are felling trees, a planned retreat path. not contact spark plug to prevent accidental starting when setting up, transporting, ad- OPERATE YOUR SAW SAFELY...
  • Page 4: Maintain Control

    S Mix and pour fuel in an outdoor area on bare ground; store fuel in a cool, dry, well ventilated place; and use an approved, marked container for all fuel purposes. Wipe up all fuel spills before starting saw. S Move at least 10 feet (3 meters) from fuel- ing site before starting engine.
  • Page 5: Kickback Safety Features

    Symmetrical Guide Bar Large Radius Tip Elbow locked S Low--Kickback Chain, designed with a contoured depth gauge and guard link which deflect kickback force and allow wood to gradually ride into the cutter. Thumb on underside of Low---Kickback handlebar Chain Contoured Depth Gauge S Keep a good, firm grip on the saw with both Elongated Guard Link...
  • Page 6 SAFETY NOTICE: when assembling the bar, that the pin located Exposure to vibrations on the adjusting screw aligns into a hole in through prolonged use of gasoline powered the bar. Turning the screw will move the ad- hand tools could cause blood vessel or nerve justment pin up and down the screw.
  • Page 7 S Fit chain drive links in bar groove. S Pull the bar forward until the chain is snug Chain Brake in the guide bar groove. Ensure all drive Nuts links are in the bar groove. S Now, install chain brake making sure the adjusting pin is positioned in the lower hole in the guide bar.
  • Page 8: Starting A Cold Engine

    To stop the engine move the ON/STOP CHOKE/FAST IDLE LEVER switch to the STOP position. To start the engine hold the saw firmly on the ground as illustrated. Make sure the FULL chain is free to turn without contacting any object.
  • Page 9: Cutting Methods

    Braking function control TREE FELLING TECHNIQUES CAUTION: The chain brake must be WARNING: Check for broken or checked several times daily. The engine dead branches which can fall while cutting must be running when performing this proce- causing serious injury. Do not cut near build- dure.
  • Page 10 NOTCH CUT AND FELLING THE CUTTING A FALLEN TREE TREE (BUCKING) Bucking is the term used for cutting a fallen S Make notch cut by cutting the top of the tree to the desired log size. notch first. Cut through of the diameter of the tree.
  • Page 11 First cut on compression side of log Second cut Second cut LIMBING AND PRUNING WARNING: Be alert for and guard against kickback. Do not allow the moving chain to contact any other branches or ob- First cut on compression side of log jects at the nose of the guide bar when limb- BUCKING WITHOUT A SUPPORT ing or pruning.
  • Page 12: Bar Maintenance

    S Next make a 2nd cut all the way BAR MAINTENANCE through the limb. Then cut a third If your saw cuts to one side, has to be forced overcut leaving a 1 to 2 inch collar from through the cut, or been run with an improper the truck of the tree.
  • Page 13: Troubleshooting Table

    S Before storing, drain all fuel from the unit. S Do not store the unit or fuel in a closed area Start engine and allow to run until it stops. where fuel vapors can reach sparks or an S Clean the unit before storing. Pay particular open flame from hot water heaters, electric attention to the air intake area, keeping it free motors or switches, furnaces, etc.
  • Page 14: Declaration Of Conformity

    DIRECTIVE and from serial numbers 2001--305(N or D)00001 and onwards, conforms to the provisions of the DIRECTIVE. The net power is 1,6 kW or 1,9 kW. For the model 2036, the measure sound power is 108,1 dB and the guaranteed sound power is 112 dB. For the model 2040, the measured sound power is 109,8 dB and the guaranteed sound power is 118 dB.
  • Page 15: Technical Data Sheet

    TECHNICAL DATA SHEET Noise levels Engine 2036 2040 2036 2040 Equivalent (see note 1) noise Cylinder volume, cm pressure level at operator ’s ear, Stroke, mm measured according to relevant Idle speed, rpm 3,000 3,000 international standards, dB(A) Recommended max.

This manual is also suitable for: