Table of Contents
Advertisement
2 Turn on the camcorder and set it to
Verify that !
[AV/Headphones] is set to [) AV].
(
3 Camcorder: Locate the scene you wish to copy and pause the
playback shortly just before the desired scene.
4 Camcorder: Resume playback.
By default, onscreen displays will be embedded in the output video
signal. You can change the displays by repeatedly pressing 3
(" 93).
5 External device: Start recording when the scene you wish to copy
appears; stop recording when it ends.
6 Camcorder: Stop playback.
NOTES
• We recommend powering the camcorder using the compact power
adapter.
! Uploading Movies to Video Sharing Web Sites
You can convert your high-definition video recordings into standard
definition in order to upload them to your favorite video sharing Web
site.
If you are using an Eye-Fi card, after converting your video recordings
into standard definition scenes you can upload your movies wirelessly,
directly from the camcorder. Refer to Eye-Fi's homepage for the latest
information on compatible Web sites.
You can complete the conversion to standard definition in the cam-
corder and then use the supplied software ImageMixer 3 SE to upload
your videos to the Web.
Installation
See 'PIXELA Applications' Installation Guide.
Using the software
See 'ImageMixer 3 SE Software Guide' (PDF file on the Transfer Utili-
ties CD-ROM).
7 When the conversion is completed, a confirmation screen will
appear.
Connect the camcorder to the computer at this point (" 144) to
continue uploading the converted videos to the Web or touch [End
Without Connecting] to connect to the computer later.
To embed the recording date and time
The recording date and time will always be displayed on the converted
scene.
[*]
[Embed Date/Time]
(
To select the bit rate
Using a higher bit rate will result in better video quality for the con-
verted scenes, while a lower bit rate will result in smaller file sizes and
faster uploads.
[*]
[Bit Rate (Quality)]
(
(
[%]
To convert only part of a scene
Instead of steps 4 and 5 above, touch on the scene you want to con-
vert to start playing it back. Pause the playback at the point where you
want the conversion to begin and continue with step 6.
NOTES
• When converting scenes in the [Playlist] or [Video Snapshot] ! [Original]/
[Playlist] index screen:
- The scenes are converted with the selected background music
(" 89) instead of the original sound.
mode.
141
External Connections
!
[On]
[%]
[%]
(
(
(
Desired option
[%]
(
(
143
External Connections
!
Operating modes:
Converting Scenes into Standard Definition
1 Power the camcorder using the compact power adapter.
2 Make sure there is a memory card in the camcorder with sufficient
available space.
3 Open the [Original], [Playlist] or [Video Snapshot] ! [Original]/
[Playlist] index screen.
• Check that you have selected the # tab (built-in memory).
• [Original] or [Video Snapshot] ! [Original] index screen: To convert all
the scenes recorded on a specific date, narrow down the scenes
shown to scenes recorded on that date (" 55).
4 Touch [%] to open the scene selection screen.
When you convert scenes from the [Playlist] index screen (including the
playlist of video snapshot scenes), you cannot select individual scenes;
instead, the entire playlist will be converted. Skip directly to step 6.
5 Touch on the individual scenes you want to convert.
• A checkmark & will appear on scenes selected. Touch a selected
scene again to remove the checkmark.
• To select all the scenes at once: Touch [Select All] instead of
touching individual scenes. (Remove in advance any checkmarks
from scenes you may have selected individually.)
6 Press ( and touch [Yes].
• If a copyright notice appears, read it
carefully and touch [OK] if you agree.
• Before touching [Yes], you can touch
[*] to change the conversion
settings as described below.
• Touch [(] to interrupt the operation
while it is in progress.
142
External Connections
!
• When converting scenes in the [Playlist]:
- All the scenes are merged into one converted scene.
- If the converted scene is too large, it will be split into smaller 10-
minute long scenes.
- When converting only part of a scene, the maximum length of the
converted scene will be 10 minutes from the starting (playback pause)
point.
- The playlist cannot be converted when its total playback time exceeds
2 hours and 30 minutes.
• The time required to convert scenes is approximately equal to the total
playback time of the converted scenes. In most cases this is still faster
than converting the scenes in the computer so we recommend you
convert scenes in the camcorder.
Connecting to the Computer and Uploading your Videos
If you are connecting the camcorder to the computer immediately after
the conversion described in the previous section, start this procedure
from step 3 below. Otherwise, start this procedure from the beginning.
1 Power the camcorder using the compact power adapter.
2 Open the [For Web Upload] index screen on the memory card.
[!]
[SD Scenes]
(
(
"
3 Connect the camcorder to the computer using the supplied USB
cable.
• Connection %. Refer to Connection Diagrams (
• If the device type selection screen appears, touch [Computer/
Printer].
• On the computer, ImageMixer 3 SE will start up automatically and the
startup screen (ImageMixer 3 Launcher) will appear.
4 Click [Web upload] and continue the operation on the computer
following the software's indications.
See also 'ImageMixer 3 SE Software Guide' (PDF file on the Transfer
Utilities CD-ROM).
144
!
External Connections
[For Web (MPEG-2)]
(
124).
"
Advertisement
Table of Contents
