Page 1
Toshiba Personal Computer Satellite P300 Maintenance Manual TOSHIBA CORPORATION File Number 960-Q08...
Page 2
The information presented in this manual has been reviewed and validated for accuracy. The included set of instructions and descriptions are accurate for the Satellite P300 Series at the time of this manual's production. However, succeeding computers and manuals are subject to change without notice.
Page 3
NOTE: “Note” contains general information that relates to your safe maintenance service. Improper repair of the computer may result in safety hazards. Toshiba requires service technicians and authorized dealers or service providers to ensure the following safety precautions are adhered to strictly.
Replacement Procedures describes the removal and replacement of the FRUs. Appendices The appendices describe the following: Handling the LCD Module Board layout Pin assignments Keyboard scan/character codes Key layout Wiring diagrams BIOS Rewrite Procedures EC/KBC Rewrite Procedures Reliability Satellite P300 Maintenance Manual (960-Q08)
Page 5
Text that you are instructed to type in is shown in the boldface type below: DISKCOPY A: B: The display Text generated by the computer that appears on its display is presented in the typeface below: Format complete System transferred Satellite P300 Maintenance Manual (960-Q08)
Power Supply Troubleshooting ..................8 Procedure 1 Power Status Check ..............8 Procedure 2 Error Code Check ..............10 Procedure 3 Connection Check..............11 Procedure 4 Charging Check ...............11 Procedure 5 Replacement Check ..............13 System Board Troubleshooting .................. 14 Satellite P300 Maintenance Manual (960-Q08)
Page 7
Diagnostic Test Program Execution Check ......34 Procedure 2 Connector Check and Replacement Check......35 Touch pad Troubleshooting ..................36 Procedure 1 Diagnostic Test Program Execution Check ......36 Procedure 2 Connector Check and Replacement Check......37 Satellite P300 Maintenance Manual (960-Q08)
Page 8
Bluetooth Troubleshooting ..................53 Procedure 2 Connector Check and Replacement Check......53 Chapter 3 Test Program for Field Tests and Diagnostics Software Overview ..............3-3 Executing the Diagnostic Test ................... 3-4 Subtest names......................3-8 System Test......................3-11 Satellite P300 Maintenance Manual (960-Q08)
Page 9
Tests an Operation ..................3-62 Common 3.21.1 How to operate a window …………………………………………3-62 ..3.21.2 How to Stop the Test Program ……………………………………. 3-62 ..3.21.3 Test Status Screen …………………………………………………3-62 ..3.21.4 Test Stop Display……………………………………………………3-64 ..Satellite P300 Maintenance Manual (960-Q08)
Page 10
Display assembly ..................... 4-33 4.11 Cover assembly......................4-39 4.12 Touch pad......................... 4-43 4.13 USB board........................ 4-44 4.14 System board......................4-46 4.15 CPU..........................4-49 4.16 LCD unit / FL inverter ..................... 4-52 4.17 Application for grease(Denka FCR-AS) on North Bridge.………………………..4-57 Satellite P300 Maintenance Manual (960-Q08)
Page 11
Pin Assignments.................... C-1 Appendix D Keyboard Scan/Character Codes ..............D-1 Appendix E Key Layout.....................E-1 Appendix F Wiring Diagrams.................... F-1 Appendix G BIOS Rewrite Procedures ................G-1 Appendix H EC/KBC Rewrite Procedures................ H-1 Appendix I Reliability......................I-1 Satellite P300 Maintenance Manual (960-Q08)
Chapter 1 Hardware Overview Features The Satellite P300 Satellite Pro P300 (Intel Platform) series are 2 spindle PCs running Intel® Core Duo Processor T8100 (800MHz) or higher Intel® Core Duo Processor T9300 (800MHz) or higher. Intel® Pentium Dual Processor T2330 or higher.
Page 17
TFT color display.. Supported via a RGB connector. Keyboard Toshiba keyboard module has (104/105/109 keys) with three LEDs design, Support Windows keys & Application keys. Multi-langue support. New Dummy card slot The new card slot (dummy card) accommodates one 5mm Type II card. The slot support 16-bit PC cards.
Page 18
One 1394 port is equipped. Multiple Digital Media Card Slot XD/MS/MS pro/SD/MMC are supported Bluetooth USB Bluetooth Module standard Ver 2.1 & EDR(Enhanced Data Rate) equipped Security Kensington Lock, Fingerprint –Enhanced Lock is also equipped. HDD Password Satellite P300 Maintenance Manual (960-Q08)
Chapter 1 Hardware Overview System Block Diagram Figure 1-2 shows the system block diagram. Figure 1-2 System block diagram for Intel Platform Satellite P300 Maintenance Manual (960-Q08)
Page 21
Chapter 1 Hardware Overview The PC contains the following components. Intel Core2 Duo Processor FSB : 667 MHz T5550(1.83GHz) T5750(2.0GHz) T5850(2.16GHz FSB : 800MHz T8100(2.10GHz) T8300(2.40GHz) T9300(2.5GHz) T9500(2.6GHz) Intel Pentium Dual FSB :533GHz T2330(1.6GHz) T2370(1.73GHz) T2390(1.86GHz) Intel Celeron FSB : 533 GHz 540(1.86GHz) 550(2.0GHz) 560(2.13GHz)
Page 22
• 10/100 LAN controller (Marvell 88E8040T-A0-NNC1C000) • GIGA LAN controller (Marvell 88E8072-B1-NNC1C000) Mini Card Wireless LAN card (BTO) 5.4 GHz DSSS/OFDM LAN card is equipped. Conformity with IEEE 802.11b/g, IEEE 802.11 a/g/n and IEEE 802.11a/b/g.. Satellite P300 Maintenance Manual (960-Q08)
Page 23
Chapter 1 Hardware Overview MODEM (Conexant x 1) Supported by on board Modem + DAA daughter card. Data and FAX transmission is available. Supports ITU-TV.90. The transfer speed of data receiving is 56kbps, of data sending is 33.6kbps and of FAX is 14.4kbps.
200GB 250GB (formatted) Speed (RPM) 5,400 Data transfer Rate - To/From Media 84.6MB/s Max. - T0/From Host 1.5Gbps (150MB/s) bus transfer rate 1.5Gbps(150MB/s) (MB/s) 12.0ms/14.0ms Average random seek time (read) (ms) Power-on-to-ready 4.0 (typ.) (sec) Satellite P300 Maintenance Manual (960-Q08)
Page 27
Chapter 1 Hardware Overview Specification HITACHI HITACHI HITACHI HITACHI Parameter HTS542512k9 HTS542516k9S HTS542520k9SA HTS542525k9SA0 SA00 Storage size (formatted) 120GB 160GB 200GB 250GB Speed (RPM) 5,400 Data transfer Rate - To/From Media 65.5MB/s 65.5MB/s 65.5MB/s 65.5MB/s - T0/From Host 1.5Gbps 1.5Gbps 1.5Gbps 1.5Gbps bus transfer rate (MB/s)
Chapter 1 Hardware Overview 1.5 Keyboard The Satellite P300 keyboard has two different kinds of placement, one is for JP style and the other is for US/UK style Figure 1-5 is a view of the keyboard for US style Figure 1-5 Keyboard for US style Figure 1-6 is a view of the keyboard for UK style.
Chapter 1 Hardware Overview Figure 1-7 is a view of the keyboard for JP style. Figure 1-7 Keyboard for JP style See Appendix E for details of the keyboard layout. Satellite P300 Maintenance Manual (960-Q08)
Chapter 1 Hardware Overview TFT Color Display The SatelliteP300 and Satellite Pro 300 Panel use CCFL to control backlight. 1.6.1 LCD Module with CCFL Backlight Figure 1-8 ~ 1-11 shows a view of the LCD module and Table 1-8 lists the specifications. Figure 1-8 LG-Philips LCD Module SatelliteP300 Maintenance Manual (960-Q08)
Chapter 1 Hardware Overview Batteries The PC has the following two batteries. Main battery Real time clock (RTC) battery Table 1-9 lists the specifications for these two batteries. Table 1-9 Battery specifications Battery Name Battery Element Output Voltage Capacity Sanyo 10.8v 4000mAh 6 cell...
About 3 days Hibernation About 1 month Battery 3 cell Approximately 1.5 days(sleep mode) Pack 6 cell Approximately 3 days(sleep mode) 9 cell Approximately 5 days(sleep mode) Approximately 1 month(shutdown mode,All type of battery pack Satellite P300 Maintenance Manual (960-Q08)
Chapter 1 Hardware Overview 1.8.3 RTC Battery The RTC battery provides the power supply to maintain the date, time, and other system information in memory. Table 1-12 lists the Time required for charges of RTC battery and data preservation time. Table 1-12 Time required for charges of RTC battery Condition Time...
Table 1-13 AC adapter specifications Parameter Specification With Led DELTA/ LITE-ON DELTA/ LITE-ON DELTA/ LITE-ON Power 120W Input voltage AC 100V/240V Input frequency 50Hz/60Hz Input current ≦ 1.5A Output voltage DC 19V Output current 3.95A 4.74A 6.3A Satellite P300 Maintenance Manual (960-Q08)
Page 44
Diagnostic Test Program Execution Check ......33 Procedure 2 Connector and Replacement Check ........34 Touch pad Troubleshooting ..................35 Procedure 1 Diagnostic Test Program Execution Check ......35 Procedure 2 Connector Check and Replacement Check......36 [CONFIDENTIAL]Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 45
Fingerprint Troubleshooting ..................51 2.15 Procedure 1 Diagnostic Test Program Execution Check ......51 Procedure 2 Connector Check and Replacement Check......51 2.16 Bluetooth Troubleshooting ..................52 Procedure 1 Connector Check and Replacement Check......52 Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
2. Implements for debugging port check • Toshiba MS-DOS system FD • RS-232C cross cable • Test board with debug port test cable • PC for displaying debug port test result Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
There are following two types of connections in the figure of board and module connection in and after 2.3 Power Supply Troubleshooting. (1) Cable connection is described in the figure as line. (2) Pin connection is described in the figure as arrow. <e.g.> Connection of modem Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Before going through the flowchart steps, verify the following: Ask him or her to enter the password if a password is registered. Verify with the customer that Toshiba Windows is installed on the hard disk. Non- Windows operating systems can cause the computer to malfunction.
13. If an error is detected on the fingerprint test, perform the fingerprint Troubleshooting Procedures in Section 2.16. 14. If an error is detected on the Bluetooth test, perform the Bluetooth Troubleshooting Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 52
2 Troubleshooting Procedures Procedures in Section 2.17. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
(even intervals) Blinks orange once The system is driven by only a battery and the battery level (at being switched on) is low. Doesn’t light Any condition other than those above. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 54
Check 2 If the DC IN icon does not light, go to Procedure 3. Check 3 If the battery icon does not light white or red, go to Procedure 4. NOTE: Use a supplied AC adapter. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Record Not Found HDC Not Reset Error Drive Not Initialized DMA Boundary Error Bad Sector Bad Track Error ECC Error ECC Recover Enabled HDC Error Seek Error Time Out Error Drive Not Ready Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 56
Caching Error Other Error Multimedia Write Error Invalid Drive Drive Not Ready Other Error NOTE: If error status name is Other Error , please reference the Error Code for error information Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Procedure 4. Procedure 4 Charging Check Check if the power supply controller charges the battery pack properly. Perform the Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 58
If the battery pack is still not charged, go to Check 5. Check 5 Replace the battery pack with a new one. If the battery pack is still not charged, go to Procedure 5. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Battery pack may be faulty. Replace it with a new one. If the problem still occurs, perform Check 2. Check 2 System board may be faulty. Replace it with a new one. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Procedure 1 and continue with the other procedures as instructed. The procedures described in this section are: Procedure 1: Message Check Procedure 2: Debugging Port Check Procedure 3: Diagnostic Test Program Execution Check Procedure 4: Replacement Check Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
The following error message appears when data stored in RAM under the resume function is lost because the battery has become discharged or the system board is damaged. Go to Procedure 3. WARNING: RESUME FAILURE. PRESS ANY KEY TO CONTINUE. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Initialize caches to initial POST values Initialize I/O component Initialize the local bus IDE Initialize Power Management Load alternate registers with initial POST values Restore CPU control word during warm boot Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 64
Set key click if enabled 58h 2-2-3-1 Test for unexpected interrupts Initialize POST display service Display prompt "Press F2 to enter SETUP" Disable CPU cache Test RAM between 512 and 640 KB Test extended memory Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 65
Search for option ROMs. One long, two short beeps on checksum failure Check for SMART Drive (optional) Shadow option ROMs Set up Power Management Initialize security engine (optional) Enable hardware interrupts Determine number of ATA and SCSI drives Set time of day Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 66
Initialize error logging Initialize error display function Initialize system error handler PnPnd dual CMOS (optional) Initialize notebook docking (optional) Initialize notebook docking late Force check (optional) Extended checksum (optional) Unknown interrupt Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 67
System memory test Initialize interrupt vectors Initialize Run Time Clock Initialize video Initialize System Management Mode 1 Output one beep before boot Boot to Mini DOS Clear Huge Segment Boot to Full DOS Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
If an error is detected during these tests, go to Procedure 4. Procedure 4 Replacement Check System board may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and replace system board with a new one. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Procedure 2. Detailed operation is given in Chapter 3, Tests and Diagnostics. If the test program cannot be executed on the computer, go to Procedure 3. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 70
“write enable”. If any other message appears, perform Check 2. Write protected Check 2 Make sure the floppy disk is formatted correctly. If it is, go to Procedure 3. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
1. Cable can not be disconnected from the connector. 2. Cable is connected straight to the connector. 3. Cable is connected all the way seated in the connector. 4. Cable can not be broken. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 72
If it does not work properly when connected to CN6, CN7, CN31, CN35 or all ports, perform Check 4. Check 4 System board may be faulty. Replace it with a new one following the steps in Chapter 4, Replacement Procedures. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
User’s Manual. Procedure 1 Partition Check Insert the Toshiba MS-DOS system disk and start the computer. Perform the following checks: Check 1 Input C: and press Enter. If you cannot change to drive C, go to Check 2. If you can change to drive C, go to Procedure 2.
2.5” HDD(s) and the connector(s) of system board may be defective (Refer to the steps described in Chapter 4, Replacement Procedures for disassembling.). Insert HDD(s) to the connector(s) firmly. If it is (or they are) firmly connected, go to Procedure 3. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Using the Diagnostic Disk, format 2.5” HDD with a format option (physical format). If HDD is formatted, set the 2.5” HDD partition using MS-DOS FDISK command. If you cannot format 2.5” HDD using the Tests and Diagnostic program, go to Procedure 4. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Chapter 4, Replacement Procedures and check the operation. If the problem still occurs, perform Check 3. Check 3 System board may be faulty. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
ONE TEST) in the Diagnostic Program. Refer to Chapter 3, Tests and Diagnostics, for more information on how to perform the test program. If an error occurs, go to Procedure 2. If an error does not occur, keyboard is functioning properly. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Chapter 4, Replacement Procedures. If the problem still occurs, perform Check 3. Check 3 System board may be faulty. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
3, Tests and Diagnostics, for more information on how to perform the test program. If an error occurs, go to Procedure 2. If an error does not occur, touch pad is functioning properly. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Chapter 4, Replacement Procedures. If the problem still occurs, perform Check 3. Check 3 System board may be faulty. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Insert the Diagnostics disk in the USB FDD, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics for details. If an error is detected, go to Procedure 3. Satellite P300 and Satellite Pro P300 Maintenance Manual...
Disassemble the computer following the steps described in Chapter 4, Replacement Procedures. If the connection is loose, reconnect firmly and restart the computer. If the problem still occurs, go to Procedure 4. Satellite P300 and Satellite Pro P300 Maintenance Manual...
Chapter 4, Replacement Procedure and test the display again. If the problem still occurs, perform Check 5. Check 5 System board may be faulty. Replace it with a new one following the instructions in Chapter 4, Replacement Procedure. Satellite P300 and Satellite Pro P300 Maintenance Manual...
If the connection is loose, reconnect it firmly and return to Procedure 2. If the problem still occurs, perform Check 2. Check 2 Optical disk drive may be faulty. Replace it with a new one following the steps in Satellite P300 and Satellite Pro P300 Maintenance Manual...
Page 86
Troubleshooting Procedures Chapter 4. If the problem still occurs, perform Check 3. Check 3 System board may be faulty. Replace it with new one following the instructions in Chapter 4. Satellite P300 and Satellite Pro P300 Maintenance Manual...
LAN board by modem cable. If modem malfunctions, the connection of cable, board and module may be defective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Satellite P300 and Satellite Pro P300 Maintenance Manual...
Page 88
Troubleshooting Procedures Check 1 Make sure the following connections are firmly connected. If any connector is disconnected, connect it firmly and return to Procedure 1. If the problem still occurs, perform Check 2. Satellite P300 and Satellite Pro P300 Maintenance Manual...
Page 89
Chapter 4. If the problem still occurs, perform Check Check 6 System board may be faulty. Replace it with a new one following the instruction in Chapter 4. Satellite P300 and Satellite Pro P300 Maintenance Manual...
LAN cable may be faulty. Replace it with a new one. If the problem still occurs, perform Check 3. Check 3 System board may be faulty. Replace it with a new one following the instruction in Chapter 4. Satellite P300 and Satellite Pro P300 Maintenance Manual...
LAN. Perform the test following the instructions described in Chapter 3. If the computer passes the test, the function is correctly working. If the computer does not pass the test, perform Procedure 2. Satellite P300 and Satellite Pro P300 Maintenance Manual...
Wireless LAN card. If wireless LAN antenna cables are not connected properly, connect them firmly and perform Procedure 1. If the problem still occurs, go to the procedure 3. Satellite P300 and Satellite Pro P300 Maintenance Manual...
Chapter 4, Replacement Procedures. If the problem still occurs, perform Check 3. Check3 System board may be faulty. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. Satellite P300 and Satellite Pro P300 Maintenance Manual...
The connection of sound system is shown in the following figure. As the connection may be defective, disassemble the PC and check each connection. If the problem still occurs, go to Procedure 2. Satellite P300 and Satellite Pro P300 Maintenance Manual...
Volume control may be faulty. Replace it with a new one following the steps in Chapter 4. Check 5 Flat cable between CN5 and CN39 may be faulty. Replace it with new cable following the instructions in Chapter 4. Satellite P300 and Satellite Pro P300 Maintenance Manual...
Fingerprint may be faulty. Replace it with a new one following the steps in Chapter 4. If the problem still occurs, perform Check 4. Check 4 System board may be faulty. Replace it with a new one following the instruction in Satellite P300 and Satellite Pro P300 Maintenance Manual...
Page 97
Troubleshooting Procedures Chapter 4. Satellite P300 and Satellite Pro P300 Maintenance Manual...
Bluetooth may be faulty. Replace it with a new one following the steps in Chapter 4. If the problem still occurs, perform Check 4. Check 4 System board may be faulty. Replace it with a new one following the instruction in Chapter 4. Satellite P300 and Satellite Pro P300 Maintenance Manual...
Page 99
Troubleshooting Procedures Satellite P300 and Satellite Pro P300 Maintenance Manual...
How to operate a window ................64 3.21.2 How to Stop the Test Program................ 64 3.21.3 Test Status Screen ................... 64 3.21.4 Test Stop Display.................... 66 3.21.5 How to enter data .................... 66 Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Test Program for Field. Tests and Diagnostics Software Overview This chapter explains how to use the Tests and Diagnostics Software for the Satellite P300 and Satellite Pro P300 computer systems. NOTES: Before starting the Tests and Diagnostics software: 1. Check all cables for loose connections.
04.LOG UTILITIES 05.SYSTEM CONFIGURATION 06.OPTION 99.EXIT 3. To select the Diagnostic Test from the Diagnostics Menu use the arrow keys to set the highlight bar to 01 and press Enter. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 104
11. Item 88 sets the floppy disk drive and hard disk drive error retry count. Item 99 exits the submenu of the Diagnostic Test and returns to the Diagnostics Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 105
14. MEMORY2 TEST 07. REAL TIME CLOCK TEST 88. FDD&HDD ERROR RETRY COUNT SET 99. EXIT TO DIAGNOSTICS MENU Use the arrow keys to highlight the desired option and press Enter. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 106
Table 3-1 in Section 3.3 lists the function of each test on the subtest menu. Table 3-2 in Section 3.15 lists the error codes and error status for each error. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
80* 25 Character Display 320* 200 Graphics Display 640* 200 Graphics Display 640* 480 Graphics Display Display Page “H” Pattern Display Video DAC Register W/R/C Color Graphics Display Color Attributes Display Color Tiling Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 108
Marching Test Working Data Test HIGH RESOLUTION VRAM W/R/C Test DISPLAY TEST 640* 480 Mode Display 800* 600 Mode Display 1024* 768 Mode Display “H” Pattern Display Focus Test (“E” Pattern) Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 109
Random Read Test Read Specified Address Test 1 point W/R/C Test MEMORY2 All one/zero Test Walking 1/Walking 0 Test(Left) Walking 1/Walking 0 Test(Right) Walking 1/Walking 0 Test(Left /Right) *This test cannot support. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Device chemistry : LION design voltage : 11100 mV Manufacturer data specification information : 2.1 Manufacture date : 9/13/2005 serial no. : 32009 STATUS : INIT Press [ESC] KEY to exit Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 111
Test Program for Field. Subtest 03 CPU Temperature This will display CPU Temperature for check , press [ESC] to exit . [CPU_TEMP.EXE] Program Version : 1.0 03-27-2007 CPU Temperature : XX Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Test data = 1H, 2H, 4H, 8H, 10H, through 80000000H. 4. Fixed data test “16 bit write/ 16 bit read” is executed and the new data is compared to the original data. Test data = FFFFFFFFH, 00000000H, 80018001H Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 113
Protected Mode [32MB - MAX] This subtest first writes data patterns and address data from 32MB to the maximum installed memory, reads the new data, and then compares the result Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 114
This subtest writes a data pattern (CCAA5533H ) in 4KB from 0 to the maximum installed memory, then waits for a memory refresh cycle (16 ms or more), reads the new data, and compares the result with the original data pattern. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 115
Stress Test This subtest writes the following 16KB data patterns to the Write/Read Buffer in conventional memory. data: FFFFFFFFFFFFFFFF0000000000000000 5555555555555555AAAAAAAAAAAAAAAA CCCCCCCCCCCCCCCC3333333333333333 0000000000000000FFFFFFFFFFFFFFFF AAAAAAAAAAAAAAAA5555555555555555 3333333333333333CCCCCCCCCCCCCCCC FFFFFFFFFFFFFFFF0000000000000000 0000000000000000FFFFFFFFFFFFFFFF 5555555555555555AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA5555555555555555 CCCCCCCCCCCCCCCC3333333333333333 3333333333333333CCCCCCCCCCCCCCCC Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
This subtest is used for the 105 keyboard and functions the same as Subtest 1. Subtest 03 Pressed Key Display [104 Keyboard] This subtest is used for the 104 keyboard and functions the same as Subtest 1. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 117
, screen will display <PRESS> in right rectangle , the program exit . If left and right button short , screen will display <Left and Right Button maybe short > , the program exit . Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 118
Test Program for Field. LEFT PRESS TOUCH_PAD TEST RIGHT PRESS Please Do Not Press the Left and Right Button At The Same Time Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR NEXT LINE SHOWS BLINKING DISPLAY BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB BLUE MAGENTA GREEN CYAN YELLOW WHITE Press [ Enter ] KEY To exit this subtest and return to the Display Test menu: Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 120
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 121
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 122
Press ENTER to display the following sixteen colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 123
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 124
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 125
Press ENTER to display the following 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white using 640*480 video resolution. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 126
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 127
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 128
” displays on the screen and then the screen flickers due will remain blank to the fast screen refresh while the test is executing. Press Ctrl + break to return to the Display Test menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 129
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 130
Pressing Enter executes VRAM mapping test which indicates vertical lines Press Enter to execute the VRAM mapping test which displays a horizontal line at one dot intervals using Mode 12. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 131
Press Enter to execute the VRAM mapping test which displays a vertical line at four dot intervals using Mode 12. Press [Enter] Key Press Enter to display VRAM mapping test using the all dots Mode. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 132
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 133
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Subtest 03 Random Address/Data This subtest writes random data to random addresses on all tracks defined in Subtest 01. The data is then read and compared to the original data. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 135
This subtest reads data from a specified track and head. The following message displays on the screen to enter the test track number and head number. TRACK NO (00~79) ?? HEAD NO (0~1) ? Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
• Random Subtest 03 Random Address Data This subtest writes random data to 1000 different random addresses on the HDD. This data is then read and compared to the original data. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 137
3.18) to specify the LBA number where the error(s) occurred during Subtest 01. The following message displays on the screen to enter the test sector count. SECTOR COUNT (01~39) ?? START ADDRESS (00000000~MAX Address) ? Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 138
This subtest writes specified data to a specified sector count, then reads and compares the result. The following message displays on the screen to enter the test data, sector count. TEST DATA ????(=37b3H) SECTOR COUNT (01~39) ?? START ADDRESS (00000000~Max Address) ? Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
If YES is selected for Test Loop on the Test Parameter menu, the screen above displays and the test is executed again. Press Ctrl + break to return to the Real Time Clock Test menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 140
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
(FFH, FEH, FEH, through 02H, 01H, 00H) is written and the new data is read and compared with the original data. The original cache memory content is then restored to the cache memory. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 142
“working data,” reads the new data and compares the result with the original data. The original cache memory content is then restored to the cache memory. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
If YES is selected for Test Loop on the Test Parameter menu, the screen displays the colors listed above. Press Ctrl + break to return to the High Resolution Display Test menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 144
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 145
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 146
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 147
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 148
Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
The Multimedia Test contains four subtests that test the computer's multimedia functions. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: Use the Toshiba Backup CD-ROM for Subtests 01, 02, and 03. Subtest 01 Sequential Read Test This subtest sequentially reads one block unit (2K bytes) of all logical addresses from the test CD.
Walking 1/Walking 0 test (Right) Tee test method is the same as Subtest2. However, the data to be used differs. 80008000800080007FFF7FFF7FFF7FFF 4000400040004000BFFFBFFFBFFFBFFF Subtest 04 Walking 1/Walking 0 test (Left/ Right) Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 151
Test Program for Field. Tee test method is the same as Subtest2. However, the data to be used differs. 7FFF7FFF7FFF7FFF8000800080008000 BFFFBFFFBFFFBFFF4000400040004000 DFFFDFFFDFFFDFFF2000200020002000 FFFBFFFBFFFBFFFB0004000400040004 FFFDFFFDFFFDFFFD0002000200020002 FFFEFFFEFFFEFFFE0001000100010001 80008000800080007FFF7FFF7FFF7FFF 4000400040004000BFFFBFFFBFFFBFFF 0004000400040004FFFBFFFBFFFBFFFB 0002000200020002FFFDFFFDFFFDFFFD 0001000100010001FFFEFFFEFFFEFFFE Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
HDC Not Reset Error Drive Not Initialized DMA Boundary Error Bad Sector Bad Track Error ECC Error ECC Recover Enabled HDC Error Seek Error Time Out Error Drive Not Ready Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 153
Caching Error Other Error Multimedia Write Error Invalid Drive Drive Not Ready Other Error NOTE: If error status name is Other Error , please reference the Error Code for error information Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
File. 7. This program is executed according to the Count Loop number selected in the Running Test Edit Item, see Section 3.20. To terminate the program, press Ctrl + Break. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
4. Serial Number ( 12345678W ) 5. OEM String ( PSL20X-XXXXX,SXXXXXXXXXX ) 6. Model Select [1]Dyn-Jpn [2]Tos-Jpn [3]Tos-Eng [4]Tos-FR 7. Write UUID ( XXXXXXXXXXXXXXXX ) 8. Brightness Write ( XXXXXXXX ) Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 156
It is for OEM pre install Windows and no need to Active , If you select Non OS , then you need to Active your OS before you use . Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Error Status Pass Count Subtest Number Read Data Test Name Write Data Error Count Error Name and Detail [[1:Next, 2:Prev, 3:Exit, 4;Clear, 5:FD Log Read, 6:FD Log Write, 7:Log Save]] Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 159
Test Abbreviations System Test Memory Test Keyboard Test Display Test Floppy Disk Test Hard Disk Test Real Time Clock Test Cache Memory Test Height Resolution Display Test Multimedia Test Memory2 Test Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
* - XXXMB MEMORY SIZE * - XXX CPU * - 1 Vedio Chip XXXXXXXXXXXXX * - 1 ODD DRIVE(S):XXXXXXXX FW Rev.:XXXX Press Enter to return to the Diagnostics Menu. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Subtest 08 Display Page Floppy Disk Test Subtest 02 Sequential W/R/C Hard Disk Test Subtest 01 Sequential Read Real Time Clock Test Subtest 02 Backup Memory Test Tab: HELP (Key Operation) Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 162
8. Select 03 from the Diagnostics Menu and press Enter to execute the Running Test. NOTE: If press Ctrl+break in the runin process, please press more one any key to exit. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Subtest No. Displays the Subtest number in the following format: ffgg ff = Subtest No. gg = Step Number (Will be blank if the test does not have a Step Number.) Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Page 164
Test Address Displays the Test Address. (The format differs for each test.) Error Status Displays the error status. Error Name Displays the name of the error. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Letters which must be entered are always shown in [ ]. Simultaneous entries are displayed by a “+” mark. For example: [a] [Enter] Press the “a” key, then press the [Enter] key. [Ctrl] + [c] Press the [Ctrl] key and the “c” key simultaneously. Satellite P300 and Satellite Pro P300 Tests and Diagnostics Manual...
Remove the Screws(back)................4-41 Figure 4-19 Disconnect the touch pad flat cable/Fingerprint cable......... 4-42 Figure 4-20 Remove the screws (front) and cover assy........... 4-43 Figure 4-21 Remove the touch pad.................. 4-45 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-iii...
Page 169
Thermal pad on North Bridge ..............4-59 Figure 4-33 Apply silicon grease on North Bridge,VGA,V-RAM........4-60 Figure 4-34 Thermal pad & VRAM position…………………………………………...4-60 Figure 4-35 Thermal pad position……………………………………………………...4-61 Figure 4-36 Thermal pad & VRAM position…………………………………………...4-62 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-iv...
The chart shows the case for the following example: • Removing a MDC All FRUs down to the “4.2 Battery pack” to “4.11 Cover assembly” above a SD board/Microphone/MDC must be removed. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
4. When connecting to the AC power supply, use only an AC adapter and cable approved by Toshiba. 5. To prevent electric shock, ensure that all replacement parts are compatible with the computer and that all cables and connectors are securely connected. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Screw sizes are noted in the text and figures. 9. As all parts have sharp edges and corners, take care not to cut yourself. 10. After replacing an FRU, check that the computer and replaced part operate correctly. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Normal pin connectors are used for all other cables. Simply pull out or push in these connectors to disconnect or reconnect. Pressure plate connector Spring connector Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
One Philips screwdriver with type 1 bit (for screws other than above) • Tweezers (for lifting screws) • ESD mats (lay on work table or floor) • An ESD wrist strap and heel grounder • Anti-static carpet or flooring Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
G r ip a r e a “Special length screw” means screws whose length is indicated in an integral number to the first decimal places such as 2.5 mm, 2.8 mm and so on. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
4. Slide and hold the battery release latch (2) to free the battery pack after moving the battery release lock (1) into it unlock position – pick the battery pack out of the computer from fillister. Release Latch 1 Latch 2 Figure 4-1 Remove the battery pack Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 178
3. Attach the battery cover to the battery pack. 4. Insert the battery pack 5. Ensure the battery release lock (1) is moved into its locked position Lock Lock1 Figure 4-2-1 Install the battery pack Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
NOTE: If a PC card is not inserted all the way, the eject button may not pop out. Be sure to push a PC card firmly and press the eject button again. Push Figure 4-2 Remove a PC card Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-10...
Page 180
The following describes the procedure for inserting a PC card (See Figure 4-2-2). 1. Make sure the PC card does not stick out. 2. Insert a PC card and press it until it is securely connected. Figure 4-3-1 Insert a PC card Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-11...
Page 181
• M2.5×4.0B FLAT BIND screw 3. Remove the following screws securing the HDD assembly. • M2.5×5.0B FLAT BIND screw 4. Disconnect the HDD assembly from the connector on the system board. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-12...
Page 182
Replacement Procedures MAIN HDD Turn Figure 4-4 the compute upside down Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-13...
Page 183
Replacement Procedures CAUTION: When a HDD is installed, they are installed in the position as the following figure. SCREW PULL TAB SCREW M2.5*5—2pcs Figure 4-5-1 Remove the MAIN HDD assembly Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-14...
Page 184
5. Remove the following screws securing the HDD holder and remove the HDD holder. • M3.0×3.0B FLAT BIND screw SCREW M3*3—4pcs HDD H=9.5mm / H=12.5mm Figure 4-4 Remove MAIN HDD Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-15...
Page 185
2. Insert the HDD assembly into the HDD slot and connect it carefully to the MAIN HDD on the system board. 3. Secure the HDD assembly with the following screw. • M2.5×4.0B FLAT BIND screw Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-16...
Page 186
• M2.5×4.0B FLAT BIND screw 6. Remove the following screws securing the HDD assembly. • M2.5×5.0B FLAT BIND screw 7. Disconnect the HDD assembly from the connector on the system board. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-17...
Page 187
Replacement Procedures SECOND HDD Figure 4-4-1 Turn the computer upside down CAUTION: When a HDD is installed, they are installed in the position as the following figure. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-18...
Page 188
Replacement Procedures SCREW SCREW M2.5*5—2pcs PULL TAB Figure 4-4-2 Remove the SECOND HDD assembly Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-19...
Page 189
8. Remove the following screws securing the HDD holder and remove the HDD holder. • M3.0×3.0B FLAT BIND screw SCREW M3*3—4pcs HDD H=9.5mm / H=12.5mm Figure 4-4-3 Remove the screws and HDD holder Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-20...
Page 190
10. Insert the HDD assembly into the HDD slot and connect it carefully to the MAIN HDD on the system board. 11. Secure the HDD assembly with the following screw. • M2.5×4.0B FLAT BIND screw Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-21...
2. Disconnect the wireless LAN antenna cable from the connectors on a wireless LAN card. 3. Open the left and right latches holding a wireless LAN card and remove a wireless LAN card from the connector on the system board. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-22...
Page 192
Replacement Procedures RAM Door 3 screws Wireless LAN with 2 screws Wireless LAN antenna cable Wireless LAN card CN30 Figure 4-5 Remove a wireless LAN card Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-23...
Page 193
LAN card and lock the secure screws. 2. Connect the wireless LAN antenna cables to the terminals on a wireless LAN card. 3. Install the wireless LAN card cover and secure it with the following screw. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-24...
(See Figure 4-6). 1. Loose the screw securing the memory slot cover. 2. Remove the memory slot cover. 3. Open the left and right latches and remove a memory module. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-25...
Page 195
Replacement Procedures RAM Door 3 screw Figure 4-6 Remove memory slot cover Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-26...
Page 196
Replacement Procedures Figure 4-6-1 Remove a memory module Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-27...
Page 197
Confirm that the new memory is detected correctly. 4. If the memory is not detected, check that it is connected correctly. Socket1 Socket2 Figure 4-7 Insert a memory module Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-28...
Then, lift up the keyboard cover to remove it. 6. Insert your finger into the keyboard slot and keyboard. Then lift up the keyboard to remove it. 7. Disconnect keyboard cable. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-29...
Page 199
Replacement Procedures Battery KB Holder 3 screw Figure 4-8 Remove screws for KB Holder Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-30...
Page 200
Replacement Procedures Keyboard 2screw KB holder Keyboard Figure 4-9 Remove the keyboard/KB Holder Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-31...
Page 201
2. Slide and set the speaker cover assembly and secure it with the following screw. • M2.5×5.0B FLAT BIND screw 3. Install the keyboard brace by pressing it from the topside. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-32...
FLAT BIND screw 2. Disconnect an optical disk drive toward the arrow direction from the connector CN26 on the system board. ODD screw Figure 4-10 Remove an optical disk drive Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-33...
Page 203
2. Insert an optical disk drive assembly into the slot and connect it to the connector CN26 on the system board. 3. Secure the ODD drive with the following screw. M2.5X5.0 Flat BIND screw X1 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-34...
1. Close the display and turn the computer upside down. 2. Open the RAM Door and remove antenna cable Connector. M2.5x4.0 FLAT BIND (Locktight) Figure 4-12 Remove the screws (securing display assembly) 4-35 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 205
3. Remove Battery and disassembly k/b holder and keyboard screw. (please refer figure 4-8,figure4-9). KB holder screw * 3 M2.5x3.0 FLAT BIND (Locktight) KB screw * 2 M2.5x5.0 FLAT BIND (Locktight) Figure 4-12-1 Remove the KB screws 4-36 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 206
4. Disassembly TOP ASSY M2.5x8.0 M2.5x5.0 M2.5x8.0 M2.5x3.0 M2.5x5.0 M2.5x6.5 M2.5x6.5 M2.5x3.0 M2.5x8.0 M2.5x5.0 Figure 4-13 Remove the screws (from bottom side) M2.5x5.0 Figure 4-14 Remove the screws (from top side) 4-37 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 207
Antenna cable LCD cable Figure 4-15 Remove the Wireless Antenna and LCD cable Opening the display to 135degree, and remove the hinge screw. ‧ M2.5×6.5 FLAT BIND screw (Locktight) M2.5x6.5 M2.5x6.5 4-38 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 208
Replacement Procedures Figure 4-16 Remove the hinge screws 4-39 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 209
6. Pulling out the pole of hinge from the hole of hinge assembly, remove the display assembly from the base assembly. Display assembly Base assembly Figure 4-17 Remove the LCD harness and remove display assembly 4-40 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 210
5. Pass the cables to the back of computer through the slot. 6. Arrange the wireless LAN antenna along the guide and contact with the connector. 7. Install the LAN board and cover ASSY of the system. 4-41 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
3. Disconnect the touch pad flat cable/Fingerprint cable from the connector on the system board. Finger print cable Power FFC cable TP FFC cable Figure 4-19 Disconnect the touch pad flat cable/Fingerprint cable 4-43 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 213
Pull up and remove the cover assembly from the base assembly. M2.0×5.0 FLAT BIND screw Front KB Holder Keyboard M2.5x5.0 TOP case assy Base case assy Figure 4-20 Remove the screws (front) and cover assy 4-44 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 214
FLAT BIND screw Back • M2.5×8.0 FLAT BIND screw Back • M2.0×3.0 FLAT BIND screw Back 4. Free the cable from cable-drain when through the antenna cable to PCB hole. 4-45 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
4. Peel off and remove the touch pad from the cover assembly. Touch pad flat cable Touch pad Finger print M2.5x3.0 cable Touch pad Touch pad board flat plate M2.5x3.0 Figure 4-21 Remove the touch pad 4-46 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 216
4. Stick the insulator on the touch pad plate. 5. Connect the touch pad flat cable to the connector on the touch pad and stick the glass tape on the connector. 4-47 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
1. Insert the usb board into base case and connect USB board cable, Modem cable 2. Fix the below screws M2.0x5.0 FLAT BIND screw NOTE: Be careful not to catch the cables between cover assembly and base assembly. 4-48 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
1. Disconnect the power cable from the system board (See Figure 4-25) Power Cable Figure 4-23 Disconnect the power cable 2. Disconnect the speaker cable, USB cable, FM CABLE, MDC CABLE and BLUETOOTH CABLE from the connector on the system board. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 219
Replacement Procedures 3. Remove the following screws securing the system board and remove the system board. (See Figure 4-26) • M2.5×5.0 BIND screw Figure 4-24 Remove the system board Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 220
2. Connect the speaker cable, USB cable, FM CABLE, MDC CABLE and BLUETOOTH CABLE to the connector on the system board. 3. Connect the power cable to the connector on the system board Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
NOTE: When removing the heat sink holder, be sure to remove the screws in the reverse order of the number marked on the holder. 3. Remove the CPU heat sink. Figure 4-25 Remove the CPU heat sink Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 222
Thermal pad for N-bridge, VGA&V-RAM for each repair NOTE: Apply the silicon grease enough to cover the chip surface using the special applicator. Thermal pad is fixed for each one, no need special applicator. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 223
7. Connect the Heat sink cable to the connector on the system board NOTE: When securing the heat sink holder, be sure to secure the screws in the order of the number marked on the holder. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
2. Insert your finger between the edge of the display mask and the LCD, and remove the display mask while releasing the latches of display mask. Figure 4-28 Remove the display mask Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 225
5. Disconnect the HV harnesses from the connectors CN2 on the FL inverter. 6. Remove the FL inverter while peeling off the double-sided tape. Insulator LCD harness FL inverter Double-sided tape HV harness Figure 4-29 Remove the FL inverter Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
LCD unit. After peeling off the CONDUTIVE tape, disconnect the LCD harness from the connector on the back of the LCD. 9. Remove the LCD unit. LCD UNIT LCD HARNESS Figure 4-30 Remove the LCD unit Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 227
10. Remove the following screws securing the LCD support (LCD unit side) and remove the LCD supports and LCD top bracket from the LCD unit. • M2.0x2.5 BINK screw Figure 4-31 Remove the LCD supports Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 228
BIND screw X8 9. Cover screws with Screw rubber cover X8 NOTE: When installing the display mask, make sure there is no gap between the display mask and the display cover. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 229
Replacement Procedures 4.17 Application for Grease (Denka FCR-AS)/Thermal pad on North Bridge, VGA,V-RAM I. For Satellite P300, Satellite Pro P300, EQUIUM P300, SATEGO P300(Intel without VGA Board) use Thermal pad on North Bridge TSB PN RW PN Used on A000032180 JXBL5016010 N-BRIDGE THERMAL PAD BL5(JXBL5016,3A)
Page 230
A000032200 JXBL5018010 VRAM1 THERMAL PAD BL5(JXBL5018,REV3A) A000032210 JXBL5019010 VRAM2 THERMAL PAD BL5(JXBL5019,REV3A) A000032220 JXBL5020010 VRAM3 THERMAL PAD BL5(JXBL5020,REV3A) A000032230 JXBL5021010 VRAM4 THERMAL PAD BL5(JXBL5021,REV3A) Figure 4-34 Thermal pad & VRAM position Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 232
Thermal pad & VRAM position NOTE: When applying for grease on North Bridge, one syringe*1cc can cover about seven repairs. Thermal pad is fixed for each one, no need special applicator and can re-use. Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained.
Page 234
Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface.
Page 235
Handling the LCD Module 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge.
Page 236
Handling the LCD Module 7. Do not expose the module directly to sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9.
Page 237
Handling the LCD Module 10. If you transport the module, do not use packing material which contains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization. New Orleans-10S10SG10A10AG10A+10AG+Maintenance Manual (960-Q08)
SATA connector (48) South Bridge (49) CN26 PATA ODD connector (50) CN23 DDR SO-DIMM Slot B (51) CN24 DDR SO-DIMM Slot A (52) PCN4 ACIN cable connector (53) CN21 WLAN Module Slot Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 242
Connect to M/B connector (02) Sensor IC Quantum QT1081 (03) Music Mute Button (04) Media Player Button (05) Music Play / Pause Button (06) Music Stop Button (07) Music Backward (08) Music Forward Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 243
Table B-3 Low Cost Function board connectors Location Function (01) Music Mute Button (02) Media Player Button (03) Music Play / Pause Button (04) Music Stop Button (05) Music Backward (06) Music Forward Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 244
Board Layout USB with RJ11 board (01) (02) USB with RJ11 Figure B-5 board layout (front) (03) (04) (05) Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 245
( USB with RJ11 Table B-4 board connectors Location Function (01) Connect to Modem module (02) Connect to M/B USB connector (03) RJ11 connector (04) USB connector (05) USB connector Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 246
Board Layout USB with FM Board (01) (02) USB with FM Figure B-7 board layout (front) (03) (04) (05) Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 247
Board Layout USB with FM back Figure B-8 board layout ( Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) B-10...
Page 248
Board Layout USB with FM Table B-5 board connectors Location Function (01) Connect to M/B FM connector (02) Connect to M/B USB connector (03) FM Jack (04) USB connector (05) USB connector Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) B-11...
Page 249
Touch Pad Board (05) (01) (02) (03) (04) (06) Touch pad Figure B-9 board layout (front) (07) (08) (09) (14) (13) (12) (11) (10) Touch pad back Figure B-10 board layout ( Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) B-12...
Page 250
(09) TP Board to TP module connector (10) LED4 ACIN LED (11) LED1 Power and Suspend LED (12) LED2 Battery Charge LED (13) LED3 HDD LED (14) LED5 Card Reader LED Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) B-13...
Page 251
Power Switch Board (01) (02) Power Switch Figure B-11 board layout (front) Power Switch Table B-7 board connectors Location Function (01) Power Button (02) CN14 Power Switch Board to M/B connector Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) B-14...
Page 252
(front) Fingerprint IC and Table B-8 board connectors Location Function (01) Finger Printer IC Authentec AES1610 (02) FP board to TP board connector (03) FP board to TP board connector Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) B-15...
Page 253
Modem Board (01) (02) Modem Figure B-13 board layout (front) Modem IC and Table B-9 board connectors Location Function (01) Modem board to M/B board connector (02) Modem IC Conexant CX20548-11Z Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) B-16...
Signal name INVCC0 LCD_VCC INVCC0 LCD_VCC INVCC0 LCD_EDIDDATA I/O LCD_EDIDCLK CCD_POWER LCD_VADJ MIC_GND_R Analog MIC_R CCD_USBP2+ DISPON CCD_USBP2- TXLCLKOUT+ I/O TXUCLKOUT+ TXLCLKOUT- TXUCLKOUT- TXLOUT0+ TXUOUT0+ TXLOUT0- TXUOUT0- TXLOUT1+ TXUOUT1+ TXLOUT1- TXUOUT1- TXLOUT2+ TXUOUT2+ Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 255
Signal name MIC_GND Analog MIC CN6 Low cost MMB Connector CONN SMD FPC 10P 1R FR(P1.0,H1.5) PIN No. Signal name PIN No. Signal name +3VPCU LOW_DET FN0# FN1# CN7 Main stream MMB Connector Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 256
PIN No. Signal name PIN No. Signal name +5VPCU NBSWON# PWRLED# CN9 Keyboard Side Connector CONN SMD FFC 34P,1R,FR(P0.8,H2.0) PIN No. Signal name PIN No. Signal name K_LED_P MY16 MY17 K_LED_P MY14 Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 257
CONN SMD FFC 14P 1R FR(P0.5,H1.5) PIN No. Signal name PIN No. Signal name +5V_TP +5VPCU TPDATA_1 TPCLK_1 TP_LED_ON_C BATLED1# BATLED0# PWRLED# SUSLED_EC IDE_LED# ACIN TP_XD_LED CN12 Felica Connector CONN SMD FPC 6P 1R FR(P0.5,H1.5) Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 258
CN14 BLUETOOTH MODULE CONNECTOR CONN SMD HEADER 10P 1R MR(P1.25,H1.9) PIN No. Signal name PIN No. Signal name BT_USBP8+_C BT_USBP8-_C WCS_CLK BT_RESET WCS_DAT USB_DETACH CN15 New card Connector CONN SMD HEADER 26P 1R MR (P1.0,H5.4) Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 259
CONN SMD HEADER 10P 1R MR(P1.25,H1.9) PIN No. Signal name PIN No. Signal name +5VPCU USB_OC2# USBP9+_C USBP9-_C USBP1+_C USBP1-_C USB_EN2# +5VPCU CN17 INT SPEAKER Connector CONN SMD HEADER 4P 1R MR(P1.25,H1.9) Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 260
T174 CRTDDAT CRTHSYNC CRTVSYNC CRTDCLK CN19 CPU FAN Connector CONN SMD WAFER,3P,1R,MS(P1.25,H4.7) PIN No. Signal name PIN No. Signal name TH_FAN_POWER_R --- FANSIG CN20 Battery Connector CONN DIP BATT 9P 1R MR(P2.0,H6.5) Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 261
MBCLK CN21 MINI-Card I (WLAN) Connector CONN SMD HEADER,52P,2R,MS(P0.8,H9) PIN No. Signal name PIN No. Signal name WLAN_WAKE# +3V_WL_VDD WCS_DATR WCS_CLKR +1.5V CLKREQ_WLAN# CLK_PCIE_WLAN# I CLK_PCIE_WLAN RF_EN_WLAN PLTRST# GPP_RX1N_WLAN +3V_WL_VDD GPP_RX1P_WLAN +1.5V Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 262
GPP_TX1P_WLAN USBP3-_C USBP3+_C +3V_WL_VDD +3V_WL_VDD WiMAX_LED#_A +1.5V +3V_WL_VDD CN22 TVOUT Connector CONN DIP MINI-DIN 4P FR(P1.0,H10.5) PIN No. Signal name PIN No. Signal name TV-LUMA TV-CHROMA CN23 DDRII SODIMM Connector1 DDR2 SO-DIMM(200P,H10.1,RVS) Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 278
X-TX3P X-TX3N LAN_VCC4 LAN_LINKLED# LAN_VCC3 LAN_ACTLED# CN30 MINI-Card II (HD Decoder) Connector CONN SMD HEADER 52P 2R MS(P0.8,H8) PIN No. Signal name PIN No. Signal name +3V_HD_VDD +1.5V LAD0_PCIE LAD1_PCIE CLK_PCIE_MINICARD# LAD2_PCIE Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 279
RF_EN_WLAN PLTRST# GPP_RX2N_MINICARD +3V_HD_VDD GPP_RX2P_MINICARD +1.5V MINI2_SMCLK GPP_TX2N_MINICARD MINI2_SMDATA GPP_TX2P_MINICARD PCLK_DBC_R PCIRST#_R +1.5V +3V_HD_VDD CN31 USB Connector CONN DIP USB HOUSING 4P 1R FR(H7.6) PIN No. Signal name PIN No. Signal name Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 280
Signal name SATA_TXP1 SATA_TXN1 SATA_RXN1_C SATA_RXP1_C +3.3VSATA2 +3.3VSATA2 +3.3VSATA2 CN33 5 IN 1 CARD READER Connector CONN SMD HOUSING 43P FR(P0.82,H7.05) PIN No. Signal name PIN No. Signal name XD_CD#_C XD_R/B#_C XD_RE#_C Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 281
SD/MS_CLK_C MS_BS/XD_D3_C MS_D2/XD_D1_C SD_D0_C MS_D0/XD_D2_C SD_D1_C MS_BS/XD_D3_C XD_D4_C XD_D5_C XD_D6_C MS_D1/XD_D7_C VCC_XD SD_CD#_C SM_WPI#/SD_WP_C CN34 SATA HDD Connector CONN DIP HOUSING 22P 1R FR(P1.27,H6.7) PIN No. Signal name PIN No. Signal name Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 282
CONN DIP USB HOUSING 4P 1R FR(H7.6) PIN No. Signal name PIN No. Signal name USBPWR0 BUSBP0- BUSBP0+ CN37 RTC Connector CONN SMD HEADER 2P MR(P1.25) PIN No. Signal name PIN No. Signal name VCCRTC Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 283
Signal name ADOGND INT_MIC_R CN40 Headphone Jack CONN DIP PHONE JACK 8P 1R FR(H6.6) PIN No. Signal name PIN No. Signal name ADOGND HPR_SYS HPL_SYS ADOGND HP_JD +3V_SPD SPDIF_OUT CN41 SYSTEM MIC Jack Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 284
PIN No. Signal name PIN No. Signal name FM_CLOCK FM_DATA FM_LEFT FM_RIGHT FM_DET FM_INTX CN43 MDC Connector CONN SMD HEADER 12P 2R MR(P0.8,H5.35) PIN No. Signal name PIN No. Signal name DIB_P DIB_N Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 285
Appendix D Display Codes Display Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Keytop Note Make Break Make Break ‘ ~ 7 & BkSp Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q0...
Page 286
Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Keytop Note Make Break Make Break Caps Lock ‘ “ Enter Shift (L) No.102 , < . > Shift (R) Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 287
Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Keytop Note Make Break Make Break Ctrl Alt (L) Space ALT (R) ← Home ↑ ↓ PgUp PgDn → Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 288
5. * This key corresponds to key No. 42 in a 102-key model. 6. * Refer to Table D-6, No. 124 key scan code. 7. * Refer to Table D-7, No. 126 key scan code. Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 289
With left Shift With right Shift Set 1 E0 AA __________ E0 B6 E0 2A ___________ E0 36 Set 2 E0 F0 12 ________ E0 F0 59 E0 12 ___________ E0 59 Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 290
AA E0 12 E0 2F E0 F0 2F E0 F0 12 Table D-4 Scan codes with Fn key Code set 1 Code set 2 Keytop Make Break Make Break CTRL LALT ARROW NUMERIC Scrl Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 291
Make Break Make Break (–) Table D-6 No.124 key scan code Code set 1 Code set 2 Shift Make Break Make Break Prt Sc Common Ctrl + Shift + Alt + Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08)
Page 292
Table D-7 No.126 key scan code Shift Code set 1 Code set 2 Make Make Pause Common* E1 1D E1 F0 Ctrl* E0 46 7E E0 F0 *: This key generates only make codes. Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 293
United Status (US) Keyboard Figure1 US Keyboard layout 2. Traditional Chinese (CH) Keyboard Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 294
Figure 2 CH Keyboard layout 3. Thai (TI) Keyboard Figure 3 TI Keyboard layout 4. Korean (KO) Keyboard Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 295
Figure 4 KO Keyboard layout 5. United Kingdom (UK) Keyboard Figure5 UK Keyboard layout Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 296
6. US International (UI) Keyboard Figure 6 UI Keyboard layout 7. Hebrew (HB) Keyboard Figure7 HB Keyboard layout Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Appendix F Wiring Diagrams F.1 RGB Monitor ID Wraparound connector Appendix F Appendix F Wiring Diagrams RGB Monitor ID Wraparound connector (1) RED (2) GREEN GREEN (2) (3) BLUE BLUE (4) NC (5) GND (6) GND (7) GND (8) GND (9) 5V (10) GND (10)
Page 311
Appendix F Wiring Diagrams F.2 LAN Loopback Connector Magnia 3100 Maintenance Manual...
BIOS have been erased or system can’t be booted . In this case, insert the BIOS rewriting disk, and the BIOS will be rewritten. Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 313
Appendix H Appendix H EC/KBC Rewrite Procedures Same as BIOS rewrite Procedures, please refer appendix G Satellite U300 and Satellite Pro U300 Maintenance Manual(960-Q08)
Appendix I Reliability Appendix I Reliability The following table shows MTBF (Mean Time Between Failures) in maximum configuration. Table I-1 MTBF Component Time (hours) System 6150 Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)
Page 315
Reliability Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08)