Table of Contents
Advertisement
RADIAL ENGINEERING
3 YEAR LIMITED WARRANTY
Radial Engineering Ltd. warrants this product to be free from defects
in material and workmanship and will remedy any such defects free of
charge according to the terms of this warranty. Radial Engineering will
repair or replace at its option any defective component(s) of this product,
excluding the fi nish, the tube, the footswitch (tubes and footswitches are
warranted for 90 days) and wear and tear from normal use, for a period
of three (3) years from the original date of purchase. In the event that a
particular product is no longer available, Radial Engineering reserves the
right to replace the product with a similar product of equal or greater value.
To make a request or claim under this limited warranty, the product must
be returned prepaid in the original shipping container (or equivalent) to
Radial Engineering or to an authorized repair centre and you must as-
sume the risk of loss or damage. A copy of the original invoice showing
date of purchase and the dealer name must accompany any request for
work to be performed under this limited warranty. This limited warranty
shall not apply if the product has been damaged due to abuse, misuse,
misapplication, accident or as a result of service or modifi cation by any
other than an authorized repair centre.
THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE
ON THE FACE HEREOF AND DESCRIBED ABOVE. NO WARRAN-
TIES WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE SHALL EXTEND BEYOND
THE RESPECTIVE WARRANTY PERIOD DESCRIBED ABOVE OF
THREE YEARS.
RADIAL ENGINEERING SHALL NOT BE RESPONSIBLE OR LIABLE
FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR
LOSS ARISING FROM THE USE OF THIS PRODUCT. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS, WHICH MAY VARY DEPENDING ON WHERE YOU
LIVE AND WHERE THE PRODUCT WAS PURCHASED.
1638 Kebet Way, Port Coquitlam BC V3C 5W9
tel: 604-942-1001 fax: 604-942-1010 email: info@radialeng.com
Tonebone PZ-Pre users guide V1.0 - Part #: R870 1205 00
www.radialeng.com
True to the Music
PZ-Pre
Acoustic Instrument Preamp
User Guide
Radial Engineering Ltd.
1638 Kebet Way, Port Coquitlam BC V3C 5W9
Tel: 604-942-1001 Fax: 604-942-1010
email: info@radialeng.com
Advertisement
Table of Contents
Related Manuals for Radial Engineering PZ-Pre
Summary of Contents for Radial Engineering PZ-Pre
-
Page 1: User Guide
To make a request or claim under this limited warranty, the product must be returned prepaid in the original shipping container (or equivalent) to Radial Engineering or to an authorized repair centre and you must as- sume the risk of loss or damage. A copy of the original invoice showing date of purchase and the dealer name must accompany any request for work to be performed under this limited warranty. -
Page 2: Table Of Contents
Users Guide have ever experienced, it is not dedicated to just guitars. We designed the PZ-Pre from the ground up to work with all types of instruments including violin, cello, contrabass, mandolin, Dobro, bouzouki, harp, sitar and banjo! In fact it will likely do a smash-up... - Page 3 15. OUTPUT: ¼” out for instrument amplifi er. monitor system so the player can control their on-stage tone 16. PHASE: (polarity) inverts the signal polarity at the ¼" with the PZ-Pre. instrument output. 27. TUNER: buffered ¼” output to feed an electronic tuner.
-
Page 4: Input Section
TRS jack. A stereo TRS cable will allow you These 100% Class-A to connect both pickups to separate PZ-Pre inputs with a single buffers allow a passive cable. From there you can toggle between the two pickup systems piezo pickup element to or blend them together. -
Page 5: Filter And Eq Section
The ¼” effects the over-all tone of the instrument. The loop SEND and RETURN jacks are notch fi lter on the PZ-Pre has two controls: used to interface with standard guitar NOTCH sweeps the frequency spectrum effects pedals such as reverb, chorus and delay. -
Page 6: Output Section
The ¼” OUTPUT jack connects to the musician’s on-stage and instrument output jack. Magnetic pickups connect directly to amplifi er. This output is at the end of the PZ-Pre signal path and the PZ-Pre with an instrument cable. is affected by all the controls. -
Page 7: Output Connection
This is primarily designed to feed stage monitors, but is also where You can connect both a magnetic and piezo pickup and use you would connect your PZ-Pre to the PA if you do not have a FOH the unique BLEND-MIX feature to blend the outputs together. -
Page 8: Setting Up The Pz-Pre
1: Less is Best! USING THE PZ-PRE EQ CONTROLS 0 dB Before you head off to your fi rst gig with the PZ-Pre, it is a good idea to familiarize yourself with the controls in your practice room Boost and investigate the various functions. -
Page 9: Controlling Feedback
Notch Filter The notch fi lter is designed to manage feedback by surgically re- The PZ-Pre gives you low-cut and notch fi lter tools to suppress moving an offending frequency while leaving the rest of the sound feedback and achieve the greatest amount of signal gain. This intact. -
Page 10: Stage Setups
Now that you are familiar with all of the functions on your PZ-Pre, The PZ-Pre is equipped with a combination effects loop and power you are set to take it out into the real world! Connect the PZ-Pre booster. The power booster is designed to allow you to increase to your PA system, monitors and/or on-stage amp. - Page 11 If it is, you should be fi ne. If not, you may fi nd that the PZ-Pre is not generating Can I control the EQ for each input separately? suffi...
-
Page 12: Specifi Cations
True to the Music Radial PZ-Pre Specifi cations Inputs 1 & 2: ¼" Phone unbalanced Input impedance: Normal 6.8k ohm Piezo 10Meg ohm PZB buffers: +10dB boost Low-cut fi lter: 75Hz / 220Hz Notch fi lter range: 56Hz - 220Hz...
Need help?
Do you have a question about the PZ-Pre and is the answer not in the manual?
Questions and answers
Can the effects loop be set permanently on, allowing the Boost to be toggled separately?
Yes, the Radial Engineering PZ-Pre effects loop can be set permanently on using the recessed LOOP ON switch. When this switch is pushed in, the effects loop remains on all the time, and the BOOST footswitch is then dedicated to toggling the power boost function separately.
This answer is automatically generated
@Mr. Anderson