SLIK PRO 700DX Operating Instructions

Inverting the Center Column

Caution
Always remove the Pan Head when replacing the Remove the Center Column Base Stopper truning
Center Column. to the way of arrow.
Inverting the Center Column(Continued)
Caution
Make sure to re-attach the Center Column
Insert the Center Column from the lower side of
Base Stopper, in order to prevent the Center
Main Body, and tighten the Locking Collar and
Column from falling out.
the Center Column Stopper.

How to change the Pan Head fixing screw

U3/8
Small
Screw
U1/4
Plate
Plate Cover
The Pan Head fixing screw is reversible for either large thread (U3/8) or
small thread (U1/4).
1. Move the Plate Cover down.
2. Loosen the small screw in about three turnings with an Allen wrench
(2mm width).
3. Loosen the Plate without removing the small screw.

Opening the Tripod Legs

Caution
Be sure to open all three legs completely in order to prevent camera
shaker, or accidental tip overs caused by unstableness.
SLIK CORPORATION
853 Kayama, Hidaka City, Saitama 350-1231, Japan Phone 81-42-989-2141, Fax. 81-42-985-0210 ©2007
Loosen the Center Column Stopper and the
Locking Collar, and then pull out the Center
Column.
By inverting the Center Column, it is possible to
do copy, and close up work.
8mm
U1/4
U3/8
4. Loosen the Pan Head fixing screw and pull it out. Then, screw it in
again after reversing top and bottom.
5. Adjust the height of screw in approx. 8mm above the Plate and then,
tighten the small screw by an Allen wrench.
6. Put the Plate Cover back.

Care of the Tripod

DO NOT apply any grease or oil to this product.
Clean with a mild detergent and a soft cloth only.
DO NOT use close to flame. Avoid extreme heat.
THINNER
OIL
Printed in Thailand.
PRO 700DX Tripod
R
Operating Instructions
Thank you very much for choosing SLIK PRO 700DX Tripod.
The SLIK Corporation has designed your tripod to be a sturdy,
rugged, dependable product that will provide you with many years of
satisfactory use.
Please take a few moments to read this instruction sheet carefully
before use so that you can take full advantage of your Tripod's many
fine features.
Retain this instruction sheet in case you might want to refer back to it.
Caution
This caution icon refers to information pertaining to important safety
procedures in preventing injuries, or damages which may occur as a
result of mishandling this product.
Prohibition
This prohibited icon refers to information pertaining to prohibited con-
tents. Please refer to instructions closely to avoid accidents.
G273-1
Components
Quick Shoe
Pan Head
Center Column
Locking Collar
Center Column
3-Position Leg Angle
Center Column Stopper
Adjustment Locks
Leg
Leg Lock
Center Column
Base Stopper
Leg Lock Lever
Rubber Leg Tip
Caution
Soft Grip is consumption and cannot be used parmanently.
Please relace it whenever ragged.
Prohibition
The bolts of the Pan Head marked " " should not be adjusted nor operated.

Equipment that can be used with this Tripod

Caution
Prohibition
This product is designed to withstand equip- Equipment with uneven weight distribution
ment up to 5kgs. Please do not use equipment should not be panned by the Quick Shoe.
exceeding this limit. A loose mounting screw may go unnoticed, and
result in a sudden accidental fall.

Specification

Length folded
Max. operating height 1,900 mm
Max. center column ext. 380 mm
Weight
Pan Head
1/4" Camera Mounting Screw
Camera Platform
Dual Axis Bubble
Main Body
Levels
Pan & Tilt Handle
Soft Grip
Handle Connecting Screw
Options
BALL HEAD 800 THREAD ADAPTER SET
Cat. No. 618 - 331
QUICK SHOE(U3/8")
Cat. No. 618-340
8mm
(1/3")
BALL HEAD 800
QUICK SHOE(U1/4")
Cat. No. 618-335
Carrying the Tripod
Caution
Prohibition
Carrying a tripod with a camera left on can
result in unexpected accidents. We therefore,
recommend that you remove your camera
when carrying the tripod.
760 mm
(29 11/12")
(74 5/6")
(14 11/12")
3.53 kg
(7lbs 13oz)
Detach Proof Groove
Release Button
Locking Lever
Vertical Tilt Handle
Panning Lock Knob
U3/8
U3/8
11mm
(5/12")