Advertisement
Quick Links
PORTSMOUTH
SINGLE CONTROL
KITCHEN PULL-OUT FAUCET
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
RECOMMENDED TOOLS
Regular Screwdriver
1
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
Make certain the SEAL (9) is properly seated in recess of spout base.
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert SUPPLY HOSES (2), SPRAY HOSE (7) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and
mounting surface. Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1).Insert all HOSES (2) and SHANK (3) through MOUNTING RING (10) and
mounting surface. Do not use putty.
Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6).
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
A
S P O U T B A S E
3
™
Phillips Screwdriver
9
1
2
7
4
5
6
8
Installation
Instructions
4285.100
4285.100F15
Adjustable Wrench
B
P U T T Y
S I N K O R
M O U N T I N G
S U R FA C E
Certified to comply with ANSI A112.18.1M
M 9 6 5 4 5 6 R ev. 1. 2
Plumbers' Putty or Caulking
Turn off water at
CAUTION
main supply.
10
9
3
2
7
4
5
6
8
Advertisement
Related Manuals for American Standard PORTSMOUTH 4285.100
Summary of Contents for American Standard PORTSMOUTH 4285.100
- Page 1 Installation Instructions PORTSMOUTH 4285.100 ™ 4285.100F15 SINGLE CONTROL KITCHEN PULL-OUT FAUCET Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M M 9 6 5 4 5 6 R ev.
- Page 2 MAKE WATER SUPPLY CONNECTIONS Turn off hot and cold water supplies before beginning. Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply (Marked with a Red Stripe) to Hot and right supply (Marked with Blue Stripe) to Cold wall supply.
- Page 3 TEST INSTALLED FAUCET Move HANDLE (1) down into "off" position. With HANDLE (1) down in "off" position, pull HAND SPRAY (2) from SPOUT (3). SPRAY (HOSE (4) should pull approximately 2 feet and direct open SPRAY END (5) into sink. Operate handle up and down, in COLD and HOT positions, to flush water lines thoroughly.
- Page 4 SERVICE If Faucet Drips Proceed As Follows: Turn VALVE in OFF position. If faucet drips, operate HANDLE several times from OFF to ON position. Do not apply excessive force. FLOW CONTROL DEVICE may accumulate dirt. To remove the FLOW CONTROL DEVICE, unthread SPRAY AND HOSE ASSEMBLY and rinse clean FLOW CONTROL DEVICE.
- Page 5 PORTSMOUTH™ SINGLE CONTROL KITCHEN PULL-OUT FAUCET MODEL NUMBERS 4285.100 4285.100F15 M964398-YYY0A HANDLE KIT M962994-0070A B U T T O N A N D S C R E W K I T M907302-YYY0A ESCUTCHEON CAP M953666-YYY220A M918506-0070A (2.2 GPM) CARTRIDGE SCREWS SPRAY WITH HOSE M953666-YYY150A (1.5 GPM)