Summary of Contents for Fisher-Price Smart Response B8870
Page 1
Swing ™ Product features and decorations may vary from picture above. Accessories sold separately. Model Number: B8870 PLEASE KEEP FOR FUTURE REFERENCE. Please read these instructions before assembly and use of this product. Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Warnings and Caution Consumer Information Occasionally a consumer may experience a problem with one WARNING of our products. If this should happen, please call us, rather than return this product to the store. Usually, we can solve the problem over the telephone or send you replacement parts. •...
Page 3
Parts 2 Accessory Bins Housing 2 Rear Legs (Shorter) 2 Front Legs (Longer) Motor Housing Toybar (Toys may be different) Front Base Bracket Rear Base (with M4 Lock Nuts) Seat with Restraint 2 Seat Tubes 2 Seat Wire Caps Seat Wire Tray Note: Tighten and loosen all screws with a Phillips screwdriver.
Page 4
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing, damaged or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts.
Page 5
Assembly Pull Up Pull Up Pull Rear Pull Rear Rear Legs Rear Base • Pull both rear legs out until they “snap” into place. • While standing on the rear base, pull the rear legs up. They should remain secured to the rear base. If you can remove the rear legs, you have not assembled them cor- rectly to the rear base.
Page 6
Assembly M4 Lock Nut Rounded Side Bracket Grooves Shown Actual Size Tall Lock Nut Seat Tubes Bottom Edge of Seat Hexagonal Opening • Position the bracket so that the tall end is toward the bottom edge of the seat. Seat Hint: The M4 lock nuts have been assembled to the bracket at Tubes the factory.
Page 7
Assembly “Press” in Place Seat Wire Seat Wire is Through Hole in Seat Wire Cap Slots Seat Wire Caps #6 x 1.59 cm ( ") Screw - 4 Shown Actual Size • Press the seat wire caps into place. • Lift the seat tubes slightly. •...
Page 8
Assembly Frame Hub Push Button Swing Tube Front of Seat Waist Belts Curved Front Crotch Belt Base • Position the seat assembly so that the front of the seat is toward the curved front base. • While pressing the buttons on the swing tubes, insert them into the frame hubs.
Battery Installation Assembly Hint: When swinging, sound or power L.E.D. slows/dims/stops, it’s time to replace the batteries! We recommend using alkaline Elastic batteries for longer battery life. Loop Elastic Loop Battery Compartment Door Installation • Locate the battery compartment door on the swing frame. •...
Securing Your Child • Check to be sure the restraint system is securely attached by IMPORTANT! Before each use, inspect this product for pulling it away from your child. The restraint system should damaged hardware, loose joints, missing parts or sharp remain attached.
Adjusting the Seat Using the Toybar Toybar Upright Semi-Recline Recline Adjust the seat angle in any of three positions: Upright, Semi-Recline or Recline. To adjust the seat angle: Push down on the seat back to position the seat wire in the desired groove in the bracket for Upright, Semi-Recline or Recline.
Page 12
Swing Modes The Smart Response Swing has two modes: Baby Sounds Activated and Parent Activated Baby Sounds Activated Parent Activated...
Page 13
Baby Sounds Activated Speed Dial Sound Sensitivity Dial Power L.E.D. Swing Mode Switch Music/Volume Switch Sound Sensitivity Dial Swing Mode Switch • Slide the switch to high sensitivity for incoming • Slide the switch to baby sounds activated. The sounds (listens for shallow sounds). power L.E.D.
Page 14
Parent Activated Power L.E.D. Swing Mode Switch Speed Dial Music/Volume Switch Swing Mode Switch Music/Volume Switch • Slide the switch to parent activated. The power L.E.D. • Select for music highest volume. lights and the swing begins swinging. • Select for music high volume.
Page 15
Storage Care The pad is machine washable. Wash the pad separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. The frame, tray, and toybar may be wiped clean using a mild cleaning solution and a damp cloth.
Need help?
Do you have a question about the Smart Response B8870 and is the answer not in the manual?
Questions and answers