Related Manuals for Jonsered HT 2124T
Summary of Contents for Jonsered HT 2124T
- Page 1 Operator′s manual Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
-
Page 2: Key To Symbols
KEY TO SYMBOLS Symbols Switch off the engine by moving the stop switch to the STOP position before carrying WARNING! Incorrect or careless use of out any checks or maintenance. a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. -
Page 3: Table Of Contents
CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Please read the operator’s manual carefully. Symbols ............... CONTENTS WARNING! Long-term exposure to noise can Contents ..............result in permanent hearing impairment. So Note the following before starting: ........ always use approved hearing protection. INTRODUCTION Dear Customer, ............ -
Page 4: Introduction
If you will sell this machine, make sure that the buyer will get the operator′s manual. Good luck on using your Jonsered machine! Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. -
Page 5: What Is What
WHAT IS WHAT? What is what? 1 Operator′s manual 13 Lock for handle (HT2124T) 2 Handle 14 Throttle control 3 Throttle lock 15 Spark plug cap and spark plug 4 Fuel cap 16 Cylinder cover 5 Choke control 17 Starter handle 6 Front handle 18 Stop switch 7 Blade guard... -
Page 6: General Safety Precautions
GENERAL SAFETY PRECAUTIONS Important WARNING! Listen out for warning signals or shouts when you are wearing hearing protection. Always remove your hearing IMPORTANT! protection as soon as the engine stops. The machine is only designed for cutting branches and HEARING PROTECTION twigs. - Page 7 GENERAL SAFETY PRECAUTIONS The life span of the machine can be reduced and the risk of Press the throttle lockout and make sure it returns to its accidents can increase if machine maintenance is not carried original position when you release it. out correctly and if service and/or repairs are not carried out professionally.
- Page 8 GENERAL SAFETY PRECAUTIONS Vibration damping system Never use a machine that has a faulty muffler. Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier. The machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and Regularly check that the muffler is securely attached to the the machine′s handle unit.
- Page 9 GENERAL SAFETY PRECAUTIONS Blades To ensure good cutting results it is important that the contact pressure between the blades is correct. The contact pressure is adjusted by turning the screws on the underside of the bar clockwise as far as they will go. Then turn the screws anticlockwise a 1/4 turn.
-
Page 10: Fuel Handling
• The transport guard must always be fitted to the cutting • For best results and performance use JONSERED two- attachment when the machine is being transported or in stroke engine oil, which is specially formulated for our air- storage. -
Page 11: Fuelling
FUEL HANDLING Mixing Fuelling • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. -
Page 12: Starting And Stopping
STARTING AND STOPPING Check before starting Choke: Set the choke control in the choke position. • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. •... -
Page 13: Working Techniques
WORKING TECHNIQUES General working instructions Safety instructions while working IMPORTANT! This section takes up the basic safety precautions for • Always ensure you have a safe and stable working working with a hedge trimmer. position. If you encounter a situation where you are uncertain how to •... -
Page 14: Basic Working Techniques
WORKING TECHNIQUES Safety instructions after completing work • The transport guard should always be fitted to the cutting attachment when the machine is not in use. • Make sure the cutting attachment has stopped before cleaning, carrying out repairs or an inspection. Disconnect the HT lead from the spark plug. -
Page 15: Maintenance
MAINTENANCE Carburettor Muffler Your Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. To ensure that the engine runs at peak performance and CAUTION! Some mufflers are fitted with a catalytic... -
Page 16: Cooling System
MAINTENANCE Cooling system Air filter To keep the working temperature as low as possible the The air filter must be regularly cleaned to remove dust and dirt machine is equipped with a cooling system. in order to avoid: • Carburettor malfunctions •... -
Page 17: Gear
There is a grease nipple and a plug for filling lubricant on the gear housing. Use a grease gun to fill with grease. This should be done after every 60 working hours. Use Jonsered special grease. CAUTION! The gear housing must not be filled completely with grease. -
Page 18: Maintenance Schedule
MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by an authorized service workshop. -
Page 19: Technical Data
TECHNICAL DATA Technical data Technical data HT2124 HT2124T Engine Cylinder displacement, cm 22,5 22,5 Cylinder bore, mm 32,0 32,0 Stroke, mm 28,0 28,0 Idle speed, rpm 3000 3000 Recommended max. speed, rpm 12000 12000 Max. engine output, acc. to ISO 8893, kW/ rpm 0,6/7000 0,6/7000 Catalytic converter muffler... -
Page 20: Ec-Declaration Of Conformity
We, Jonsered, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Jonsered HT2124 and HT2124T from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:... - Page 24 Original instructions 1153206-26 ´®z+U4^¶67¨ ´®z+U4^¶67¨ 2009-11-13...