Using Your Sentry System™ Control - AGA marvel 6SDZE Operating And Maintenance Instructions Manual

Initial Power-Up:
Your product will start upon plug-in to power receptacle.
The Sentry System LED will be displaying "power failure"
on dual-zone models, (Figure 5), to indicate that a power
outage has occurred. This is normal as the product was
powered-up at the factory for quality assurance testing.
Momentarily press and release the "ON/OFF" keypad to
reset the control alarm status. The LED should indicate no
alarms. To turn the unit ON/OFF, press and hold the "ON/
OFF" key for a minimum of 5 seconds.
Set Display Temperature Units:
Your control is factory set to display temperature in °Fahr-
enheit as indicated by °F in the upper right corner of the
temperature display. If this is the desired temperature
units, no action is required. If you prefer to display tem-
perature in °Celsius, momentarily press the "°F/°C" keypad.
°C should now be displayed in the upper right corner of the
temperature display. You may "toggle" between °F or °C
temperature display at any time by momentarily pressing
the "°F/°C" keypad.
Set Your Desired Storage Compartment Tem-
perature:
Your control is factory set to 55°F. This is the ideal long-
term storage temperature for "both" red and white wines.
The storage compartment temperature can be adjusted
throughout the full range of red and white wine serving
temperatures, (40°F > 65°F).
The control allows independent temperature control for
both the upper and lower storage compartments. On Dual
Zone models, momentarily pressing the "Set" keypad will
select each compartment individually as indicated by SET
being displayed in the "Upper" or "Lower" compartment
temperature display. While SET is displayed, you may
press the "Warmer" or "Colder" keypads to adjust the stor-
age compartment set-point to your desired temperature. To
exit SET mode, momentarily press the "Set" keypad until
SET is no longer displayed in either the Upper or Lower
displays, or SET mode will time-out after 10 seconds of
inactivity.
USING YOUR SENTRY SYSTEM™ CONTROL
Figure 5 "Dual Zone"
Glass Door Models
NOTE
Compartment temperatures will be controlled to the tem-
perature displayed when SET mode is exited.
It is suggested to allow 24 hours after changing the storage
compartment set-point temperatures before making further
adjustments. This will allow the content temperatures to
stabilize at the new set-point temperature. Frequent door
openings may prolong this stabilization period.
Interior Lighting:
A door activated interior compartment light is provided for
your convenience. On glass door models only, this light
may also be used to enhance the display of your wines
through the glass door. To activate the display lighting
mode on glass door models, momentarily press the "Light"
keypad, (Figure 5). When activated, the interior light will
remain on when the door is closed.
Important: Use the display lighting option only when need-
ed. The interior light generates heat which will increase the
energy consumption of your product.
Alarms:
All Sentry control systems will alert you to conditions that
could affect the storage compartment temperature. All
alarm conditions can be silenced and re-set by momentarily
pressing the "ON/OFF" keypad.
• Door Open Alarm – If the door remains open for over
five(5) minutes, an audible alarm will occur and the
indicator LED will display "Door Ajar". Closing the door
will terminate and re-set this alarm condition.
• High / Low Temperature – If your storage compartment
experiences an excessive temperature excursion from
the set-point temperature for an extended period of
time, an audible alarm will sound, and will display "Hi
/ Low Temp". This condition may result from exces-
sive usage/door openings, warm content loading, or
product malfunction. It is recommended that you check
the condition of the stored items, and if alarm recurs,
you should initiate a service call to confirm your unit is
operating properly, (see Trouble Shooting section for
details).
6
Status
message
ON OFF Door Ajar
Power Failure
Hi / Low Temp Upper
Hi / Low Temp Lower