Related Manuals for Zenoah HTZ7500
Summary of Contents for Zenoah HTZ7500
- Page 1 HTZ7500 / CHTZ6000 / CHTZ7500 115 34 55-10 (001) OWNER’S MANUAL HEDGE TRIMMERS HTZ7500 CHTZ6000 CHTZ7500 Original Language GB-1...
- Page 2 HTZ7500 / CHTZ6000 / CHTZ7500 EC DECLARATION OF CONFORMITY (Applies to Europe only) The undersigned manufacturer, Husqvarna Zenoah Co.,Ltd., 1-9, Minamidai, Kawagoe, Saitama, Japan, declares under sole responsibility that the following products referred to in this declaration conform with the requirement of the following COUNCIL’S DIRECTIVE.
- Page 3 HTZ7500 / CHTZ6000 / CHTZ7500 EXPLANATION OF SYMBOLS AND SAFETY WARNINGS HTZ7500 WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection. CHTZ6000/CHTZ7500 WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection. MODEL SOUND LEVEL VIBRATION LEVEL...
-
Page 4: Table Of Contents
HTZ7500 / CHTZ6000 / CHTZ7500 SAFETY FIRST Contents Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken 1. Parts location ..........3 into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions 2. -
Page 5: Specifications
Max. output 1.09Hp (0.8kW) at 8000 / min (rpm) Idle speed 3000±200 / min (rpm) Fuel mixture (Gasoline 50 : Oil 1) (when using ZENOAH genuine oil) Carburetor Walbro Diaphragm type Spark plug NGK CMR7H Fuel tank capacity 0.47 (litter) Specifications are subject to change without notice. -
Page 6: For Safe Operation
HTZ7500 / CHTZ6000 / CHTZ7500 5. For safe operation gases contain dangerous carbon 1. THIS MACHINE CAN CAUSE monoxide. SERIOUS INJURIES. Read this 2. Never use the product, manual carefully until you com- a. when the ground is slippery pletely understand and follow all or when you can’t maintain a... - Page 7 HTZ7500 / CHTZ6000 / CHTZ7500 5. For safe operation IMPORTANT WARNING Check and follow the local regula- • Never place the throttle into the tions as to sound level and hours of high-speed position when start- operations for the product.
- Page 8 HANDLING FUEL 1. The engine of the ZENOAH prod- • IF SOMEONE COMES uct is designed to run on a mixed 1. Guard against hazardous situa- fuel, which contains highly flam- tions at all times.
-
Page 9: Fuel
• The Zenoah engines are lubricated by oil specially spillage around the unit. formulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle 1. Select bare ground for fueling. -
Page 10: Operation
HTZ7500 / CHTZ6000 / CHTZ7500 7. Operation STARTING ENGINE 6. While holding the unit firmly, pull out the starter rope quickly until engine fires. 1. Feed fuel into the fuel tank and tighten the cap se- curely. 2. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start moving upon starting of the engine. - Page 11 HTZ7500 / CHTZ6000 / CHTZ7500 7. Operation STOPPING ENGINE WARNING With the engine idling (3000 rpm), the blade should not move. We recommend that you have the dealer or an authorised mechanic carry out any carbure- tor adjustments. CUTTING WORK...
- Page 12 ■ HEDGE TRIMMING TECHNIQUES Trim sides of a hedge first, and then the top. Vertical cut: • With the single-sided blade hedge-trimmer, model HTZ7500 always cut from the bottom up. Cut slowly, specially with thick hedges. WARNING Always follow the safety precautions.
-
Page 13: Maintenance
HTZ7500 / CHTZ6000 / CHTZ7500 8. Maintenance Every Every Every Before System/components Procedure Note hours hours hours after after after ✔ fuel leaks, fuel spillage wipe out ✔ ✔ fuel tank, air filter, fuel filter inspect/clean replace, if necessary see adjusting replace carburetor ✔... - Page 14 HTZ7500 / CHTZ6000 / CHTZ7500 8. Maintenance BLADE IMPORTANT • Clean any resin and plant reside from the blade be- fore and after using the machine. • Note that using any spark plug other than those des- • Check the cutting edges and reform with a flat file.
-
Page 15: Storage
Grease nipple: falling off of engine and/or blade. A type • [HTZ7500] Check periodically if the rubber cushions are not deformed or damaged. Use greese pump. Feed greese until it comes out of the • [CHTZ6000/CHTZ7500] Check periodically if the base of blades. -
Page 16: Troubleshooting Guide
→ clogged with dust → consult with the repair specialty store When your unit seems to need further service, please consult with our ZENOAH service shop in your area. 11. Disposal • When you dispose of the machine, do not disassemble the machine.