Related Manuals for Zenoah CHTZ6000
Summary of Contents for Zenoah CHTZ6000
- Page 1 OWNER’S MANUAL HEDGE-TRIMMERS CHTZ6000 • Before using our products, please read this manual CAUTION carefully to understand the proper use of your unit. • Keep this manual handy. HTZ7500 848D3K93A0 (402)
-
Page 2: Table Of Contents
English SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. -
Page 3: Parts Location
English 1. PARTS LOCATION 1. Right handle 2. Fuel tank 3. Starter 4. Left handle 5. Throttle lever 6. Engine switch 7. Throttle Cable 8. Muffler 9. Blade 10. Front handle 11. Rear handle 12. Plate receive... -
Page 4: Symbols On The Machine
English WARNING 1. CLEANER Please inspect the cleaner every day for dirt. Please clean out any dust that is found up to the element on the carburetor side. When rebuilding the cleaner, be sure to follow the following order: → felt → element. If element dust remains on the cleaner when it is used, the dust may... -
Page 5: Safety Precautions
English 3. SAFETY PRECAUTIONS ■ BEFORE USING THE MACHINE a. Read this owner's manual carefully to understand how to operate this unit properly. b. This product has been designed for use in trimming leaves and branches from trees and hedges, and it should never be used for any other purpose since doing so could result in unforeseen... - Page 6 English 3. SAFETY PRECAUTIONS g. Lack of sleep, tiredness, or physical exhaustion results in lower attention spans, and this in turn leads to accidents and injury. Limit the amount of time over which the hedge-trimmer is to be used continuously to somewhere around 30~40 minutes per session, and take 10~20 minutes of rest between work sessions.
- Page 7 English 3. SAFETY PRECAUTIONS ■ WARNING CONSIDERING HANDLING OF FUEL a. The engine of this product is designed to run on a mixed fuel which contains highly flammable gasoline. You should never store cans of fuel or refill the fuel tank in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other...
- Page 8 English 3. SAFETY PRECAUTIONS persons, always check the presence and locations of others so as to maintain a distance each person sufficient to ensure safety. c. Make sure that there are no loose screws or bolts, fuel leaks, ruptures, dents, or any other problems which might interfere with safe operation.
- Page 9 English 3. SAFETY PRECAUTIONS ■ KICKBACK SAFETY PRECAUTIONS • A dangerous reaction may occur when the spinning blade contacts a solid object in the critical area. It is called Kick back. As a result, the operator can lose control of the unit which can cause serious or fatal injury.
- Page 10 KOMATSU ZENOAH authorized servicing dealer for assistance. b. Under no circumstances should you ever take apart the hedge- trimmer or alter it in any way.
- Page 11 When replacing blade or any other parts or when replacing the oil or any lubricants, always be sure to use only KOMATSU ZENOAH products or products which have been certified by KOMATSU ZENOAH for use with the hedge- trimmer.
-
Page 12: Fuel
2 cycle engines. The Komatsu Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Komatsu Zenoah genuine oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use. -
Page 13: Operation
[HTZ7500] [CHTZ6000] English 5. OPERATION ■ STARTING THE ENGINE WARNING Keep blades clear everything around It as they will start moving upon the engine starts. 1. Release the throttle lever and make sure it is fully back. (F1) 2. Set the engine switch to the “I (RUN)”... - Page 14 ■ HOW TO USE HANDLE [CHTZ6000 only] (F7) To reduce fatigue when trimming hedges, the handle can be swivelled through 90° to the left or right. Do not press the throttle during this operation! Proceed as follows: 1.
- Page 15 English 5. OPERATION • Use only as much throttle as is needed to do the job. Excessive engine speed is unnecessary. • Avoid cutting thick branches, for which will damage the blades and shorten the life of drive systems. • Tilting the trimmer 5 to 10° to the cutting object will make the job easy and bring a good result.
-
Page 16: Maintenance
6. MAINTENANCE System/compornent fuel leaks, fuel spillage fuel tank, air filter, fuel filter idle adjusting screw spark plug cylinder fins, intake air cooling vent muffler, spark arrester, cylinder exhaust port throttle lever, ignition switch cutting parts gear case screws/nuts/bolts Before Procedure ✔... - Page 17 English 6. MAINTENANCE WARNING Before cleaning, inspecting, or repairing the unit, make sure that the engine has stopped and is cool. ■ BLADE (F10) • Check the blade and the fasteners for looseness, cracking, or bending. • Check the cutting edges and reform with a flat file.
- Page 18 • [HTZ7500] Check periodically if the rubber cushions are not deformed or damaged. • [CHTZ6000] Check periodically if the springs are not deformed or damaged. ■ AIR CLEANER (F14) Release the air cleaner cover and remove dusts.
- Page 19 English 6. MAINTENANCE ■ FUEL FILTER (F15) When the engine runs short of fuel supply, check the fuel strainer for blockage. ■ WAY OF THE COOLING AIR (F16) This engine is air-cooled. Dust clogging between the inlet port of the cooling air and cylinder fins will cause overheating of the engine.
- Page 20 English 6. MAINTENANCE ■ MUFFLER AFTER 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent at the same time. (F19) (1) screw driver (2) muffler 2.
-
Page 21: Specifications
English 7. SPECIFICATIONS Model name ... HTZ7500 [CHTZ6000] Type ...Reciprocating single-sided [double-sided] dual blades Blade length ... 750 [600]mm Engine model ... Zenoah GZ23N Displacement ... 23.6cc Carburetor ... Diaphragm type Ignition system ... C.D.I Spark plug ... Champion RZ7C Fuel ... - Page 22 Working for a better tomorrow Head Office: 1-9, Minamidai, Kawagoe-city, Saitama, 350-1192 Japan Telephone: (+81)49-243-1117 Telecopier: (+81)49-243-7197 PRINTED IN JAPAN...