Related Manuals for Monogram 224D3735P001
Summary of Contents for Monogram 224D3735P001
- Page 1 Design Guide with Installation Instructions Pub. No. 49-60706 Part No. 224D3735P001 03-14 GE monogram.com...
-
Page 2: Table Of Contents
Proper installation is the responsibility of the installer. Product failure due to improper installation is not IMPORTANT • Save these instructions covered under the GE Appliance Warranty. See the for local inspector’s use. Observe all governing codes Owner’s Manual for warranty information. and ordinances. WARNING: Note to Installer •... -
Page 3: The Installation Space
Allow 25” minimum clearance for a full 130° door swing. Allow 15” for pan removal. • Water line can enter the opening through the floor or back wall. Route GE SmartConnect kit or 1/4” O.D. ™ ” min. clearance to a wall, copper tubing between the cold water line and the for framed and stainless steel models. -
Page 4: 130° Door Swing
Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets Refrigerator may require filler strips to prevent 23-7/8" From interference with cabinet door swing. Rear of The opening must allow for filler strips. Refrigerator 1"... -
Page 5: 90° Door Swing
Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and Refrigerator sides. Therefore, frameless cabinets may require Case Trim filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips. 23-7/8" From Rear of Refrigerator 1/4"... -
Page 6: Customization Basics
Design Guide CUSTOMIZATION BASICS: Framed Or Overlay Panels, Custom Handles and Accessory Kits Professional Style Stainless Steel Refrigerators Overlay panels Stainless steel wrapped refrigerators with beveled edges You may also choose to install custom overlay panels from and professional style handles. These models are shipped your cabinet manufacturer. -
Page 7: Panel Dimensions
Design Guide 1/4” FRAMED PANEL DIMENSIONS 5/16" Trim If you choose to install framed panels, they must be cut Door Reveal to the dimensions shown. The panels will slide into the frame on the door, drawer and grille. 1/4" If the custom panel is less than 1/4” thick and if it fits Panel loosely in the door frame, it can be backed up with a piece of filler material or foam tape to improve the fit. -
Page 8: Side Panels
Design Guide SIDE PANELS ZUG2 GRILLE PANEL DIMENSIONS Side panels must be used whenever the sides of the The ZUG2 unified grille panel kit provides for the refrigerator will be exposed. The 1/4 ” side panels will installation of a framed or overlay grille panel. slip into the side case trim. -
Page 9: Grounding The Refrigerator
Installation Instructions TOOLS REQUIRED MATERIALS REQUIRED • Tinsnips to cut banding • 35” long 2x4 for Anti-Tip support • Stepladder • 1/4” copper water line tubing or GE SmartConnect ™ • Bucket Refrigerator Tubing kits • Level • Water shut-off valve •... -
Page 10: Step 1 Remove Packaging
Floor the refrigerator. Allow enough tubing to accommodate bend leading into the water line connection. Waterline Tubing NOTE: The only GE-approved plastic tubing is supplied in the GE SmartConnect Refrigerator Tubing kits. Do not use ™ • Turn on the main water supply and flush debris. Run about any other plastic water supply line because the line is under a quart of water through the tubing into a bucket. -
Page 11: Step 2A, Ro Water Line
Installation Instructions STEP 3 INSTALL SIDE PANELS Skip this step when not using side panels If you are using 1/4” side panels, they should be inserted into the case fastener strips before setting refrigerator in place. STEP 4 INSTALL ANTI-TIP BRACKET WARNING: ANTI-TIP PRECAUTIONS The unit is top-heavy and must be secured to prevent... -
Page 12: Installation Instructions
Installation Instructions STEP 4 INSTALL ANTI-TIP BRACKET (cont.) Install Wall Toggles: • Insert the bolts into the toggle by hand until snug. The wall toggles and bolts can be ordered as Service Kit Tighten with a wrench. #WR49X10193. Wall toggles are installed in the drywall and metal studs for stability. -
Page 13: Step 5, Level Refrigerator
Installation Instructions STEP 5 LEVEL REFRIGERATOR STEP 6 SECURE UNIT TO WALL All models have 4-point leveling. The front is supported • The “L” rod can be found in the upper left corner of by leveling legs, the rear is supported by adjustable the unit in the access compartment. -
Page 14: Step 8, Install Grille Panel
Installation Instructions STEP 7 ADJUST DOOR SWING STEP 8 INSTALL GRILLE PANEL NOTE: This refrigerator has a 2-position door stop. • Raise the grille panel to stop position. When space does not allow the door to swing open fully to 130°, you may change the door swing to a 90° opening. - Page 15 Installation Instructions STEP 9 INSTALL 1/4” FRAMED PANELS Right hand models shown. Use the same instructions for left hand models. IF YOU ARE INSTALLING OVERLAY PANELS, GO TO STEP 9A. Standard supplied handle shown in 1/4” panel position. Install door and drawer panels: •...
-
Page 16: Step 9A Install Overlay Panels
Installation Instructions STEP 9A INSTALL OVERLAY PANELS Right hand models shown. Use the same instructions for left hand models. Use Front Hol to Secure Hand Use Rear Holes to Secure Trim Supplied handle shown in the overlay panel position. Install door and drawer panels: •... -
Page 17: Step 10 Connect Water Supply
Insert tube into the union fitting on the unit and tighten nut to union. • Turn on the water to check for leaks. GE SmartConnect Tubing: ™ • Insert the molded end of the tubing into the refrigerator connection. -
Page 18: Step 13 Install Toekick
Installation Instructions STEP 13 INSTALL TOEKICK assembly with the 3 screws provided, adjust to the desired height and tighten the screws. • A custom toekick can be installed to match or complement the surrounding cabinetry. Use the supplied toekick as a template to cut the shape. IMPORTANT: The gap between the bottom of the refrigerator cabinet and the top of the toekick must remain unobstructed for proper air circulation. - Page 19 Notes...
- Page 20 ® 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. GE Consumer & Industrial Appliances General Electric Company Pub. No. 49-60706 Louisville, KY 40225 GEAppliances.com Part No.