Introduction Balanced Stereo Limiter The LIM012 balanced stereo limiter is a small size, easy to use, device that can be used for limiting the signal coming from an input device such as a mix-table, microphone, etc… that is then send to a (power)amplifier. Limiting this input signal will not only protect your PA system, but also enables you to comply to restrictions by law. When the input signal of this input device exceeds the desired level, the LIM012 will attenuate the output signal sent to the output device in such a way that it will again reach the desired level. This level can be set by turning the Limit switch and can be limited at 6 different levels: 0 dBV, -6 dBV, -12 dBV, -18 dBV, -24 dBV and -30 dBV. At the bottom the green LED’s indicate the limit level. When the output signal is exceeding the desired Level, attenuation will take place and the red LED will indicate the location of the Limitation (Left or Right). The LIM012 balanced Stereo Limiter has 2 channels that work separately whereby it can be used as a stereo, or 2 x mono limiter. The LIM012 needs to be connected to a 24 DC power source. The PSD242 Power supply is included.
Environment Do not place the unit in environments which contain high levels of dust, heat, moisture or vibration. Do not use the unit near water or other liquids. Make sure no water or other liquids can be spilled, dripped or splashed on the unit. The unit is developed for indoor use only. Do not use it outdoors. Do not place objects (books, vases, … ) on top of the unit. Place the unit on a stable base or mount it in a stable rack.
Chapter 1 Safety requirements Always handle the unit with care. Only use a grounded socket outlet and a power cord with grounding plug to plug in the unit. This unit is not a toy. It should not be operated by children. Do not open the unit. (risk for electrical shock) CAUTION - SERVICING This unit contains no user serviceable parts. Refer all servicing to qualified service personnel. Do not perform any servicing unless you are qualified to do so. NOTE T his produc t conforms to the following European S t andards: EN 50081-1: 1992, EN 50082-1: 1992, EN 60065: 1994...
Chapter 2 Pin connections and connectors Connection standards: The in- and output connections of AUDAC audio equipment are performed corresponding to international wiring standards for professional audio equipment. XLR: 1 = Ground / Shield 2 = Signal + 3 = Signal - XLR Female: XLR Male:...
Chapter 3 Overview LIM012 Front panel The front panel of the LIM012 contains all the controls and indicators. 1) Power switch: By toggling this switch, the power for the LIM012 can be switched ON and OFF. The power LED will illuminate when the power is switched ON. 2) Limiting level adjustment switch: By changing the position of this rotatable selection switch, the limiting level can be adjusted. The switch has 6 different positions whereby the limiting level can be set between -30 dBV and 0 dBV. A screwdriver should be used to change the position. 3) Limiting level indication LED’s: By means of these green LED’s the selected limiting level will be indicated. The LED located next to the selected limiting level will illuminate when device is operating. 4) Limiting indication LED’s: These red LED’s will illuminate when the signal of the corresponding channel is beïng overdriven compared to the selected limit level. The limit circuit will intervene bringing the output signal to the selected level.
Rear panel At the rear panel of the LIM012 are all the connections provided. 1) 24 Volts power connector: The included 24 volts power supply (PSD242) should be connected to this connector. Pay attention to the polarity when connecting the power supply. 2) XLR Input connectors: The signal coming from the input device such as an audio source, mixing table, pre- amplifier should be connected to the 3-pin Female XLR inputs. 3) XLR Output connectors: The output signal is available at these 3-pin Male XLR connectors. The output signal is the audio signal which is driven through the limiting circuit. The level of the output signal will always be lower or equal to the selected limiting level.
Chapter 4 LIM012 Quick start guide This chapter guides you through the setup process of a basic project with one LIM012 Balanced Stereo Limiter, an audio source device (mixing table) and a power amplifier. Overview of the LIM012 setup 1) Connecting the LIM012...
Chapter 5 Additional information Technical specifications Peripheral Inputs 2 x Balanced Line audio input Outputs 2 x Balanced Line audio output Connectors Audio input 3-Pin Female XLR Audio output 3-Pin Male XLR Power 2-pin Euro Terminal Block Specifications Level range -30 dBV to 0 dBV THD+N < 0.15% Signal / Noise > 90 dB Frequency response 20 Hz - 20 kHz Other Power supply 24V DC PSD242 switching power supply included 100 ~ 240V AC / 47~63 Hz Weight 0.415 Kg Dimensions 110 x 44 x 160 mm Shipping weight & volume 1.20 Kg - 0.0078 Cbm...
Need help?
Do you have a question about the LIM012 and is the answer not in the manual?
Questions and answers