Page 2
Designed and developed by helicopter experts, the all-in- Throttle channels allowing the cyclic servos to be powered at one integrated design of the AR7100 takes the hassle out of installing high voltage for increased performance while the gyro and throttle Note: The AR7100/AR7100R uses a specifically designed switch.
Voltage input - 6.0 to 10.0 volts/ 5 to 7 cell NiMH or 2-cell LiPo LiPo Receiver Pack 1350mAh - SPMB1350LP* the AR7100 will continue to operate down to 3.5 volts, the AR7100/ Minimum receiver operational voltage - 3.5 volts LiPo Receiver Pack 2000mAh - SPMB2000LP* AR7100R features a built-in 5.2-volt regulator for the Rudder, Aux...
In this example using 2000mAh batteries 2000 x 60% = 1200mAh (available usable capacity) divided by the capacity used per 8 minute flight, 153mAh would allow up to 7 flights of 8 minutes each. Spektrum AR7100 Spektrum AR7100...
• Mount the switch and insert the switch plug into the port in the bracket is adjustable for 50-size or 90-size engines by extending or main unit marked SWITCH. Note: The AR7100/AR7100R uses a specifically designed switch. Conventionally wired switches are not retracting the rpm sensor and fastening the screw in place.
Page 6
Install the adaptor lead as shown to the right. operation. 6. After you’ve programmed your model, it’s important to rebind the system so the true low throttle and neutral control surface positions are stored in the receiver. Spektrum AR7100 Spektrum AR7100...
Page 7
Preset Failsafe. During the binding process the bind plug is left in throughout the important to perform a range check. All Spektrum aircraft transmitters remote receivers are operating optimally and that the installation process and is removed only after the receiver connects to the incorporate a range testing system which reduces the output power, (position of the receivers) is optimized for the specific aircraft.
Page 8
If the RF link is performing optimally, frame losses per antenna fades (A, B, R) allows you to evaluate the performance the Flight Log into the Data port on the AR7100/AR7100R. The flight should be less than 20. A hold occurs when 45 consecutive of each receiver.
Page 9
RevLimit Instructions (AR7100R only) Connections Modes of Operation The Spektrum AR7100R features an integrated RevLimit limiter. The RevLimit is totally integrated and the target rpm is adjusted via The RevLimit target rpm is adjusted thru the Gear channel (channel In the travel adjust screen two values can be selected that will The RevLimit functions as a digital rpm limiter preventing the main the Gear channel (channel 5).
Page 10
The ACT LED on the receiver will flash green indicating that the calibration mode is successfully entered. 5. Raise and lower the throttle stick throughout its full range. The throttle endpoint will be stored. Spektrum AR7100 Spektrum AR7100...
EXCLUSIVE REMEDY OF THE PURCHASER. This warranty covers only those Products Adjust the gear channel’s travel adjust (DX7) or the limiter program to The Spektrum AR7100R RevLimit feature employs technology How the Limiter Works purchased from an authorized Horizon dealer. Third party transactions are not covered select the desired target rpm’s.
Page 12
Repair or replacement decisions are at the sole discretion of Horizon Hobby. Please call 877-504-0233 or e-mail us at Productsupport@horizonhobby.com with any questions or concerns regarding this product or warranty. Spektrum AR7100 Spektrum AR7100...
Page 13
For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product. Spektrum AR7100 Spektrum AR7100...
Need help?
Do you have a question about the AR7100 and is the answer not in the manual?
Questions and answers