18 volt cordless 3/8" drill & flashlight kit (16 pages)
Summary of Contents for Drill Master 91396
Page 1
18v cordless drill/flashlight Model 91396 set up and operating instructions visit our website at: http://www.harborfreight.com read this material before using this product. failure to do so can result in serious injury. save this Manual. Copyright 2004 by Harbor Freight Tools .
Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. REV 10b, 10e SKU 91396 for technical questions, please call 1-800-444-3353. Page 2...
Be sure the power switch is off before plugging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. SKU 91396 for technical questions, please call 1-800-444-3353. Page 3...
Accessories that may be suitable for one tool may become hazardous when used on another tool. SKU 91396 for technical questions, please call 1-800-444-3353. Page 4...
Battery (11a) is seven hours. thereafter, charge the Battery only from five to seven hours. never charge the Battery (11a) more than seven hours continuously. SKU 91396 for technical questions, please call 1-800-444-3353. Page 5...
Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. Protect the extension cords from sharp objects, excessive heat, and damp or wet areas. SKU 91396 for technical questions, please call 1-800-444-3353. Page 7...
Page 8
15 and 16 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. SKU 91396 for technical questions, please call 1-800-444-3353.
Page 9
Indicator Light will remain on until the Battery Charger is disconnected from the electrical outlet. Recharging the Battery more than 7 hours can cause damage to the Battery cells. (see figure d.) SKU 91396 for technical questions, please call 1-800-444-3353. Page 9...
Page 10
Drill/Driver Bit or Driver Extension all the way into the Chuck. While holding the Chuck Sleeve in place, turn the Chuck clockwise to lock the Drill/Driver Bit or Extension in place. (see figure e.) SKU 91396 for technical questions, please call 1-800-444-3353. Page 10...
Page 11
When you have drilled the hole, remove the drill bit from the hole while the Drill is still running. This prevents the drill bit from getting caught in the hole and causing damage. SKU 91396 for technical questions, please call 1-800-444-3353. Page 11...
Page 12
Insert a new Bulb by aligning the tabs on the Bulb with the slots in the Lamp Reflector (6B). Push in on the new Bulb while turning it counterclockwise. Then, re-attach the Lamp Screen and Lamp Cover Ring. (see figure f.) SKU 91396 for technical questions, please call 1-800-444-3353. Page 12...
Flashlight Kit. A mild detergent may be used. Do not use solvents. Do not immerse the Drill or Flashlight in any liquid. When storing, always keep the Drill, Flashlight, and accessories in a clean, dry location. rev 05k SKU 91396 for technical questions, please call 1-800-444-3353. Page 13...
Page 14
Torque Setting Ring Battery asseMBlY diagraM - drill note: Some parts are listed and shown for illustration purposes only, and are not available individually as original or replacement parts. rev 07j, 10b SKU 91396 for technical questions, please call 1-800-444-3353. Page 14...
Page 15
Switch Stun Screw asseMBlY diagraM - flashlight 16B,17B,18B, 19B,20B,21B,22B note: Some parts are listed and shown for illustration purposes only, and are not available individually as original or replacement parts. SKU 91396 for technical questions, please call 1-800-444-3353. Page 15...
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 REV 10b SKU 91396 for technical questions, please call 1-800-444-3353. Page 16...