Table of Contents
Advertisement
Model VS60
Preface
Please take time to carefully read and understand the
following instructions before you install or attempt to oper-
ate this equipment. Becoming familiar with the product
and its correct operating procedures will help assure you of
maximum musical enjoyment and reliable operation. The
effort you invest now will be well rewarded in the years
ahead.
Packaging
Save all the packaging in a dry place. Your Audio
Research amplifier is a precision electronic instrument and
should be properly cartoned any time shipment is made.
Because of its weight, it is highly probable that the unit will
be damaged during shipment if repackaged in cartoning
other than that designed for the unit.
You may not have occasion to return the unit to the factory
for service, but if that should prove necessary, or other
occasion to ship it occurs, the original packaging may save
your investment from unnecessary damage, delay and
expense.
Unpacking
The VS60 is packed in a heavy-duty carton with special
foam inserts for maximum protection. Because of the
weight of the unit and because it is a precision electronic
instrument, it is necessary to take reasonable care during
unpacking and preparation for use.
Open the carton with a small knife to carefully slit the
taped edges of the top flaps. Fold the flaps to the sides and
remove the tubes packed in foam blocks. Roll the unit in
the carton upside down on a soft surface and lift the carton
off and turn the unit right side up, then remove the foam
inserts. Carefully remove the plastic wrap. Keep all foam
inserts and store the carton system for future use.
Accessories
1 – Plastic screwdriver for bias adjustments
User replaceable spare fuses include:
1 – 5 Amp MDQ slo-blo with 120V units or 100V units
1 – T4A 250V slo-blo with 220V/240V units
Warnings
1. Do not touch hot tubes. Keep away from children.
2. To prevent fire or shock hazard, do not expose your
VS60 to rain or moisture.
3. This unit contains voltages which can cause serious
injury or death. Do not operate with covers removed.
Refer servicing to your authorized Audio Research dealer
or other qualified personnel.
4. The 14-gauge, 3-conductor detachable power cord on
your VS60 is equipped with a standard 3-prong ground-
ing plug. If used normally, it will provide a safe earth
ground connection of the chassis. Refer to the section on
"AC Power Connections" for detailed information.
5. For continued protection against fire hazard,
replace fuses only with the same type and rating of fuses
as specified.
Preparation for Use
Your VS60 amplifier is shipped with the vacuum tubes
packed in foam blocks. These must be unpacked and
installed before you attempt to operate the amplifier. In-
cluded are two matched pair of 6550 output tubes, and two
6H30 dual triodes used in the input stage. Proceed
according to the following instructions.
1. Carefully remove each vacuum tube from its
protective foam and match its location "V" number (writ-
ten on the base of the tube) to the "V" number printed
next to each socket. Firmly seat each tube in its match-
ing socket, taking care to "key" the tube pins to the
socket holes. Retain the foam blocks with other packing
materials for possible future use.
2. If you are using the optional tube cover, be sure the VS60
is first turned off and then remove the top plate with the
phillips screwdriver provided with the tube cover. Install
the tube cover in place of the top plate, using the new
screws supplied.
Panel Controls
The front panel has:
1 – Switch:
1-Power line On-Off
1 – Indicator:
1 - Power "On" LED (Green)
Use of Controls
POWER-ON/OFF SWITCH: Initiates/terminates AC line
power to the amplifier. Function indicated by green LED
above switch.
Note: If you turn off the VS60 wait at least two minutes
before turning it on again. This brief cool down period
will reduce stress on the output tubes and potential
damage to them.
Audio Research does not recommend leaving your VS60
"on" 24 hours a day as is the custom of some audiophiles to
achieve maximum sonic performance on demand. While
this is often recommended for solid-state equipment, Audio
Research does not recommend this procedure for vacuum
tube power amplifiers. (2,000 hours of tube life will pass by
in 84 days!)
1
Advertisement
Table of Contents
