Important Notice This guide is delivered subject to the following conditions and restrictions: This guide contains proprietary information belonging to RISCO Group. Such information is supplied solely for the purpose of assisting explicitly and properly authorized users of the system.
Featuring remote management, advanced communication, simple installation, and a comprehensive range of peripherals, Agility 3 with video verification is the ideal wireless solution for your residential and small commercial requirements.
Agility 3 User Manual status of each sensor to detect problems. If the panel detects trouble it will notify you with beeps and indicator lights on the panel itself. The following diagram shows the components that make up the system: 1.3 User Operating Tools...
Page 7
Agility system from any location. In addition to all the capabilities of the Smartphone app, with the web application users can also configure RISCO’s PIR Camera settings such as the number of images taken, image resolution, and more.
Agility 3 User Manual Cloud server. 1.4 Status Indications LED Indicators The LED indicators provide typical system indications, as discussed below. Some indicators have additional functions, which are explained later on. Power LED (Green) The Power LED indicates system operation.
For example: Email Messaging Using the Agility IP Module or the RISCO Cloud, the system can send event messages by Email to predefined e-mail addresses informing you of the status of the security system and certain events that occurred in the system.
Agility 3 User Manual Sound Indications In addition to the visual indications provided by the Agility’s LEDs, your system produces audible notification after certain events. Condition Description Intrusion alarm Continues rapid beeping Fire alarm Staggered rapid beeping Exit delay Slow buzzer beeps until the Exit Delay time period...
Agility 3 User Manual Chapter 2 - Local System Operation 2.1 Setting your system Setting your system causes the intrusion detectors to trigger an alarm when violated. The setting operation will be followed by a local message announcement (if defined).
Agility 3 User Manual Click Full Set Part set (Home) setting: Part set setting activates only perimeter detectors (as defined by your engineer), enabling individuals to remain inside and move about the premises while the system is partially set. To set using...
Agility 3 User Manual To set using Partition setting (Full set or Part set) procedure Quick mode: > High security mode: + code > Quick mode: > High security mode: + code or proximity tag > Press button or button 4 (if defined. Advise with your engineer) Send SMS: [Code][S or P] [Partition 1,2 or 3].
Agility 3 User Manual 2.2 Unsetting your system Unsetting your system causes the detectors not to trigger an alarm when violated. When you enter the premises, the Entry Delay begins to count down. You must unset the system within the Entry Delay time to prevent the system from triggering an alarm. The unsetting operation will be followed by a local message announcement (if defined).
Agility 3 User Manual Enter your user code and click UNSET Partition unsetting: Partition unsetting enables you to unset individual partitions within a set system To unset using Procedure for Partition Unsetting Quick mode: > High security mode: > Code >...
Agility 3 User Manual If an "Entry door" is opened prior to unsetting the system, the following voice announcement message will be heard: "Alarm occurred in the system". Press the key will indicate the cause of the alarm. Note: If an alarm occurred in the system, it is recommended to leave the premises.
Agility 3 User Manual To enable local reset by your engineer you may need to authorize him/her using the master code after the engineer enters his/her code. A one hour time window is opened for the engineer to program user functions and be able to reset your system locally 2.3 Sending a Panic Alarm...
Page 18
Agility 3 User Manual Press the panic button Page 18...
Agility 3 User Manual Chapter 3 - Remote System Operation 3.1 Remote Phone Operation The Agility enables you to operate the system from a remote touch-tone phone by initiating a telephone call to or from the system and interacting with voice menus that guide you through your required remote operation.
Agility 3 User Manual Operation Quick Key Combination Changing Zone Omit status Press [3] followed by the zone number and then [#][9] Operating Programmable Press [4] followed by the output number outputs Changing Follow Me(FM) Press [5] followed by the FM number and [#][2].
Agility 3 User Manual Notes: If no voice is detected, the event message will start playing 5 seconds after phone pick up. Press [#] to begin playback of the event message from the beginning. To repeat the Event Announcement message press [#].
Agility 3 User Manual To listen in or talk: From the Operations/Acknowledge menu, press [6]. The following messages are announced: “To Listen In press 1, To Talk press [2], To Listen and Talk (Open channel) press [3], To return to the previous menu, Press [ ...
Android play store . Self registration To enable the use of the iRISCO App, register your panel to the RISCO cloud. Note: If using GPRS verify with your engineer that your panel is set to GPRS communication...
Agility 3 User Manual Navigate your browser to www.riscocloud.com/register Enter your details in the form. In the Panel ID field copy the 15 digits of the panel from the label located on the side of the panel or as printed on the postcard that arrived with the panel.
Agility 3 User Manual Chapter 4 - User Functions and Settings The functions and settings explained in this chapter can only be performed via your LCD keypad and the Configuration Software. This chapter refers to these functions and settings as performed via the LCD keypad. Refer to the Configuration Software manual for more information regarding how these functions and settings are performed via the Configuration Software.
Page 26
Agility 3 User Manual Setting / Changing User Codes The user assigned the Grand Master authority level can change all user codes but cannot view the digits in the user code fields. Users with other authority levels can only change their own codes.
Agility 3 User Manual The display will show: "Delete User. Are you sure?". Use the key to select [Y] and press . If successful, a single confirmation beep is sounded, if not, 3 quick error beeps are sounded Repeat the above steps for deleting additional codes 4.2 Proximity Tags...
Agility 3 User Manual Deleting a proximity tag Deleting proximity tags can be done by in two options: By user number: Use this option to delete a tag for which the user is known By tag: Use this option to delete a tag for which the user is not known ...
Agility 3 User Manual Enter the phone number, including the area code (if required) or an e-mail address, as requested on the screen and press Up to 32 digits can be included in the phone number. If required, include the special functions described below to achieve the related effect.
Agility 3 User Manual Select the Scheduling program index number. Use the key to activate / deactivate and press 4.5 Macro keys Programming Macro Keys Agility enables the engineer or Grand Master to record a series of commands and assign them to a macro.
Agility 3 User Manual Represents Deletes your entry from the cursor position forward and 0 simultaneously Use to toggle between / ///#/ and all of the numeric characters Used to end the sequence and save it to memory Press to save your entry.
Page 32
Agility 3 User Manual Operation Grand User Engineer Master Walk test: Used to easily test and evaluate the operation √ √ of selected zones in your system Output Control: Allows user control of previously √ √ designated external devices (e.g. an appliance, a motor- driven garage door, etc.)
Page 33
Agility 3 User Manual Operation Grand User Engineer Master Advanced View IP Address: Use this option to view √ the IP address of the Agility. Advanced CS Connect: Enables to establish √ √ communication with the configuration software at a predefined location through IP or GPRS.
Agility 3 User Manual Chapter 5 - System Specifications The following technical specifications are applicable for the Agility: Electrical Characteristics System Power 230VAC (-15%+10%), 50Hz, 50mA Optional: 9VAC, 50-60Hz Units Consumptions Main board: Typical 130mA GSM: Stand by 35mA, Communication 300mA...
Agility 3 User Manual Chapter 6 - EN 50131 Compliance Compliance Statement Hereby, RISCO Group declares that the Agility series of central units and accessories are designed to comply with: EN50131-1, EN50131-3 Grade 2 EN50130-5 Environmental class II EN50131-6 Type A...
Agility 3 User Manual Appendix A - Keypad User Operations The following section details the user operations from the 2-way LCD wireless keypad. User operation can be defined to be activated by a quick mode or high security mode that requires the use of a code or proximity tag.
Page 37
Agility 3 User Manual Operation Quick Operation High Security Mode Fire Alarm Press and hold simultaneously for 2 seconds Emergency/Medical Press and hold simultaneously for 2 seconds Alarm System Chime Press and hold the button for 2 seconds On/Off Main Unit Speaker...
Agility 3 User Manual Operation Quick Operation High Security Mode Changing Keypad Press and hold simultaneously for 2 seconds. Select the Language language and press to confirm. All operations are available while keypad is turned on (Not in Sleep Mode)
Agility 3 User Manual Appendix B - Remote Control User Operations The following section details the user operations from the Agility 2-Way Remote Control. User operation can be defined to be activated by a quick mode or high security mode that requires the use of a code.
Agility 3 User Manual Code Status LED/Buzzer Indications After each transmission (indicated by a flashing Green LED) from the remote control, the Agility sends a status response indicated by the remote control's LEDs and Buzzer: LED Indications Operation 1st LED *...
Agility 3 User Manual Appendix C - Engineer Event Log Messages Event Message Description Activate PO=xx PO XX activation Actv PO=xx KF=zz PO XX is activated from remote control ZZ AL Reinstate P=y Alarm reinstatement on partition Y Alarm abort P=y...
Page 42
Agility 3 User Manual Event Message Description Comm OK Sounder=y Communication OK between the Agility and Sounder Y Comm. OK GSM Communication OK between the Agility and GSM Comm.OK I/O Mdl. Communication OK between the Agility and I/O module * Conf. alarm P=y Confirmed alarm occurred in partition Y ...
Page 43
Agility 3 User Manual Event Message Description * GSM: Module comm. Internal GSM/GPRS BUS module fault * GSM:NET avail. GSM network is not available GSM:NET avail.OK GSM Network is available GSM:NET signl.OK GSM Network quality is acceptable GSM:NET signal The GSM RSSI level is low...
Page 44
Agility 3 User Manual Event Message Description * Ksw full set:P=y Partition Y is set by key switch * Ksw unset:P=y Partition Y is unset by key switch L.bat rstr KF=yy Low battery fault restore from wireless remote control YY L.Temp rst Zn=xx...
Page 45
Agility 3 User Manual Event Message Description Soak fail Z=xx Zone XX has failed in the soak test Special KP=y Special alarm from the from wireless keypad Y Spkr l.bat rsS=y Speaker low battery restore from sounder Y * Spkr low bat S=y...
Agility 3 User Manual Appendix D: Web User Application The Web User Application provides a full interface to your system from a PC, cellular phone or PDA using the WAP portal. Via the Web you can perform a wide range of tasks such as set/unset, zone omit, user code management and output control.
Agility 3 User Manual Menu Bar Home Workspace Status Menu Bar Use the Menu Bar to access the set/unset application functionality as per the above diagram. The following options are available from the Main Menu: Home – pressing the Home button allows the user to return to the Main page at any time ...
Agility 3 User Manual Workspace The workspace offers additional links to the following pages of the application, including: Users and Codes, History, Alerts, Change Password, Video. When you choose a page, either from the Main Menu, or from the workspace, the page is displayed in the workspace.
Page 49
Agility 3 User Manual User code management The Users and Codes page enables you to manage your system's users. The page displays a table of the system's current users and enables you add, edit and delete users as required. Please note that this capability is available only to a user with a Master code, the highest level of authorization.
Page 50
Agility 3 User Manual When you use a controlled user code for setting and unsetting, the system notifies the monitoring service. You can assign these codes to your children or employees whose comings and goings are of interest to you.
Agility 3 User Manual Deleting a User To delete a user: Click Delete for the user you want to remove from the table; the confirmation page opens. Click Yes to confirm. Web Interface Users and Codes The Web Interface Users and Codes page provides a useful tool for managing your system’s users.
Agility 3 User Manual Verify Password Change Password Click Settings then Change Password to change the password you use to login to the Web Application. Zone Omit On The Main Page menu, click SETTINGS then Zone Omit to omit specified zones in your home that you don't want to receive event messages from.
Page 53
Agility 3 User Manual Why would you need to omit a zone? If a window or door has been left open, the system status will appear as "Not Ready". Nevertheless, you may want to set the rest of the system and close that window or door when you arrive home.
Page 54
Agility 3 User Manual Alerts The Alerts feature allows those people included in your contact list to be notified by email when certain events occur. To add alert notification recipients to your contact list On the SETTINGS tab, click the Alerts sub-menu to display the following:...
Agility 3 User Manual Event Log History The History page displays a log of events that have occurred within your system. For each event you can view the date and time that the event occurred, a description of the event and the user or device that caused the event.
Page 56
Agility 3 User Manual Video Verification Using the 2-way wireless video verification PIR detectors installed in your home, the Web Application enables you to view live images over the Web through the Cameras sub- menu. Use the Images sub-menu to browse Stored Video Events images.
Page 57
Agility 3 User Manual Colored Image YES(1) YES/NO Specifies whether the captured and transmitted photographic image is to be color or black and white. Flash YES(1) YES/NO Specifies if an image capture is to be enhanced with a light flash.
Page 58
Agility 3 User Manual To control automated outputs: In the Action column, choose Turn On or Turn Off for the outputs that you wish to control. Click Update. To add a new device: Click Add New (located at the bottom of the device table); the Edit Device page opens.
Agility 3 User Manual FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This...
Page 60
Agility 3 User Manual RISCO Group Limited Warranty RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and workmanship under normal use for 24 months from the date of production. Because Seller does not install or connect the product and because the product may be used in conjunction with products not manufactured by the Seller, Seller cannot guarantee the performance of the security system which uses this product.
Need help?
Do you have a question about the Agility 3 and is the answer not in the manual?
Questions and answers