IBM 171 Parts Manual page 77

Updated October 16, 2007
Asm– Part
Index Number
25–
– 41J7434
– 44M1899
– 44M1900
– 41J7438
– 41J7442
– 44D0405
– 44D0407
– 41J7446
–1 28R3196
–2 28R3189
–2 28R3274
–3 41D9769
–4 41J9310
–4 41D9818
–4 41J9318
–4 41D9820
–5 41J8438
–5 28R3279
–6 28R3298
–6 28R3275
–7 28R3197
–8 41J7666
–9 28R3285
–10 28R3283
–11 28R3284
–12 28R3172
–13 41J7426
–14 41J6928
–15 41D7146
–15 41J8450
–16 28R3195
–17 41J7448
–17 41J7450
–18 41J8332
–18 44M1913
–18 44M1914
–18 41J8334
–19 28R3194
–20 41J7425
–21 41D7150
–21 41J8452
– 41J7126
– 41J7127
– 41J8854
– 41J8855
– 41J8856
– 42H1161
– 41J8336
Units Description
See "How to Use This Parts Manual" on page v for general parts manual
information, including ordering parts. See "Identifying a Right Hand or Left Hand
Model" on page v for how to identify left hand and right hand models.
1 Transport conveyor assembly, 19 in., 115V
1 Transport conveyor assembly with Sensormatic, 19 in., 115V, right hand
1 Transport conveyor assembly with Sensormatic, 19 in., 115V, left hand
1 Transport conveyor assembly, 19 in., 230V
1 Transport conveyor assembly, 25 in., 115V
1 Transport conveyor assembly with Sensormatic, 25 in., 115V, right hand
1 Transport conveyor assembly with Sensormatic, 25 in., 115V, left hand
1 Transport conveyor assembly, 25 in., 230V
1 Guide, tracking, motor end (order with 28R3195). Adhesive plastic sticker.
1 Belt, transport conveyor (for standard lane with 19 inch belt)
1 Belt, transport conveyor (for wide lane with 25 inch belt)
1 LED light visor mount (not shown, located on motor cable)
1 Motorized pulley, 19" conveyor 115-60hz, unbalanced (transport only)
1 Motorized pulley, 19" transport conveyor 230V
1 Motorized pulley, 25" conveyor 115-60hz, unbalanced (transport only)
1 Motorized pulley, 25" transport conveyor 230V
1 Crossbar, conveyor frame (for standard lane with 19 inch belt)
1 Crossbar, conveyor frame (for wide lane with 25 inch belt)
1 Roller (for standard lane with 19 inch belt)
1 Roller (for wide lane with 25 inch belt)
1 Guide, tracking, motor end (order with 28R3194). Adhesive plastic sticker.
2 Bracket, drive isolation. Large black coupling. Use to adjust and isolate motor. (one
on each side)
2 Drive roller retaining angle (one on each side)
2 Block, idler roller (one on each side)
2 Bracket, tensioner (one on each side)
1 Nosebar adjusting angle
1 Plate, side, transport conveyor, left side
1 Emitter/detector bracket, bagging area full sensor
1 Emitter, bagging area full sensor (for standard lane with 19 inch belt)
1 Emitter, bagging area full sensor (for wide lane with 25 inch belt)
1 Guide, tracking, motor end (order with 28R3196). Adhesive plastic sticker.
1 Assembly, nosebar, (for standard lane with 19 inch belt) (Replaces 28R7098)
1 Assembly, nosebar, (for wide lane with 25 inch belt) (Replaces 28R7084)
1 Skid plate, (for standard lane with 19 inch belt), no Sensormatic
1 Skid plate with Sensormatic opening, (for standard lane with 19 inch belt), right
hand
1 Skid plate with Sensormatic opening, (for standard lane with 19 inch belt), left hand
1 Skid plate, (for wide lane with 25 inch belt), no Sensormatic
1 Guide, tracking, motor end (order with 28R3197). Adhesive plastic sticker.
1 Plate, side, transport conveyor, right side plate
1 Detector, bagging area full sensor (for standard lane with 19 inch belt)
1 Detector, bagging area full sensor (for wide lane with 25 inch belt)
1 25 inch order separator (not shown). See 42–1 on page 121.
1 19 inch order separator (not shown). See 42–1 on page 121.
1 Sensor cable, transition plate (not shown)
1 Transition plate emitter (not shown)
1 Transition plate detector (not shown)
1 Cable tie (not shown)
1 Wire cord clips (bag of 10)
Assembly 25: (continued)
Chapter 4. Transport Conveyor
65