IBM 171 Parts Manual page 73

Updated October 16, 2007
Asm– Part
Index Number
24–
– 41J7432
– 41J7436
– 41J7440
– 41J7444
–1 41J8791
–1 41J8896
–2 41J9127
–2 41J8340
–2 41J8848
–3 41D9782
–3 41J8867
–4 41J9312
–4 41D9816
–4 41J9320
–4 41D9822
–5 28R3196
–6 28R3298
–6 28R3275
–7 28R3284
–8 28R3285
–9 41J7666
–10 28R3283
–11 41J9845
–12 41J9845
–12 41J8344
– 41J8854
–13 41J8850
–14 41D9783
–15 28R3191
–15 28R3277
–16 28R3194
–17 28R3192
–17 28R3278
–18 41J8338
–18 28R3279
–19 41J7448
–19 41J7450
–20 28R3195
–21 28R3190
–21 28R3276
–22 28R3172
Units Description
See "How to Use This Parts Manual" on page v for general parts manual
information, including ordering parts. See "Identifying a Right Hand or Left Hand
Model" on page v for how to identify left hand and right hand models.
1 Security conveyor assembly, 19 in., 115V
1 Security conveyor assembly, 19 in., 230V
1 Security conveyor assembly, 25 in., 115V
1 Security conveyor assembly, 25 in., 230V
1 Skid plate (for standard lane with 19 inch belt)
1 Skid plate (for wide lane with 25 inch belt)
1 Plate, front transition, with sensors (for standard lane with 19 inch belt)
1 Plate, front transition, with sensors (for wide lane with 25 inch belt)
1 Plate, front transition (for wide lane with 25 inch belt) (includes support bracket)
1 Card stop bracket (mounted under the transition plate) (for standard lane with 19
inch belt)
1 Card stop bracket (mounted under the transition plate) (for wide lane with 25 inch
belt)
1 Motorized pulley, 19" security conveyor 115V-60hz, balanced
1 Motorized pulley, 19" security conveyor 230V-50hz, balanced
1 Motorized pulley, 25" security conveyor 115V-60hz, balanced
1 Motorized pulley, 25" security conveyor 230V-50hz, balanced
1 Guide, tracking, nose end (order with 28R3195). Adhesive plastic sticker. Reduces
friction between belt and metal sides.
1 Roller, idler (for standard lane with 19 inch belt)
1 Roller, idler (for wide lane with 25 inch belt)
2 Angle adjuster (one on each side)
2 Drive roller retaining angle (one on each side)
2 Bracket, drive isolation. Large black coupling. Use to adjust and isolate motor. (one
on each side)
2 Block, idler roller (one on each side)
1 Emitter, flat pack sensor assembly, replaces 40M9507, (Flat pack sensor
assemblies for the emitter and detector should be replaced as a set. Order
41J9849 detector.)
1 Exit sensor emitter (for standard lane with 19 inch belt)
1 Exit sensor emitter (for wide lane with 25 inch belt)
1 Sensor cable, transition plate (not shown)
1 2nd emitter mounting bracket
1 Exit sensor mounting bracket
1 Plate, conveyer, left side (for standard lane with 19 inch belt)
1 Plate, conveyer, left side (for wide lane with 25 inch belt)
1 Guide, tracking, motor end (order with 28R3197). Adhesive plastic sticker. Reduces
friction between belt and metal sides.
1 Belt, security conveyor, with roller (for standard lane with 19 inch belt)
1 Belt, security conveyor, with roller (for wide lane with 25 inch belt)
1 Crossbar, conveyor frame (for standard lane with 19 inch belt) Aluminum bar.
(Replaces 28R3180)
1 Crossbar, conveyor frame (for wide lane with 25 inch belt)
1 Nose bar assembly (for standard lane with 19 inch belt)
1 Nose bar assembly (for wide lane with 25 inch belt)
1 Guide, tracking, motor end (order with 28R3196). Adhesive plastic sticker. Reduces
friction between belt and metal sides.
1 Plate, conveyer, right side (for standard lane with 19 inch belt)
1 Plate, conveyer, right side (for wide lane with 25 inch belt)
1 Nose bar angle adjuster
Assembly 24: (continued)
Chapter 3. Security Conveyor
61