FCC Caution FCC Part 15.19 Caution: 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including i nterference that may cause undesired operation 2.
Chapter 1 Introduction Product Appearance LED Indicator Status Description: Function Color Status Description Power indicator Green Power is being applied to this product System is ready to work Blin king Status Reset is in progress Green 30ms activity Blin king WPS function in progress 120ms Wireless is connected...
Chapter 2 System and Network Setup The BRF70N is an easy to setup and wireless device for various application and environment, especially for large installs such as hotels, offices space, warehouses, hot-spots and more. To begin with BRF70N , you must have the following minimum system requirements. If your system can’t correspond to the following requirements, you might get some unknown troubles...
parameters, so it can work properly in your network environment. Before you connect to the wireless router and start configuration procedures, your computer must be able to get an IP address from the wireless router automatically (use dynamic IP address). If it’s set to use static IP address, or you’re unsure, please follow the below instructions to configure your computer with dynamic IP address: If the operating system of your computer is….
2.3.2 Windows XP Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Internet Connections icon, click Network Connections, then double-click Local Area Connection, Local Area Connection Status window will appear, and then click “Properties”. Select “Obtain an IP address automatically”...
2.3.3 Windows Vista / Windows 7 Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Click View Network Status and Tasks, and then click Manage Network Connections. Right-click Local Area Network, then select “Properties”. Local Area Connection Properties window will appear, select “Internet Protocol Version 4 (TCP / IPv4)”, and then click “Properties”.
Router IP Address Lookup After the IP address setup was completed, please clicks “start” → “run” at the bottom-lower corner of your desktop: Input “cmd”, and then click “OK”. http://www.sapido.com.tw/ User Manual v1. 0.0...
IP address of the wireless router in address bar, and the following message should be shown. Please click “admin” to login the BRF70N . Enter the User name and Password in to the blank and then Click Login. The default values for User Name and Password are admin (all in lowercase letters).
Input User Name and New Password, then input Confirm Password again. Chapter 3 Internet Connection This Chapter describes how to setup BRF70N to the internet. The BRF70N is delivered with the following factory default parameters. Default IP address: 192.168.1.1 Default IP subnet mask: 255.255.255.0 Web login user name: admin http://www.sapido.com.tw/...
Web login password: admin Using as a broadband router Open a Web browser, and enter http://192.168.1.1 (Default Gateway) into the blank. Enter the User name and Password into the blank and then click Login. The default values for User Name and Password are admin (all in lowercase letters). Status page Download pdadd...
Page 16
Office Control Cont rol、IP Filtering、IP Binding and QoS Firmware Upgrade This function allows you upgrade the BRF70N firmware to new version. Please note do not power off the devic e during the upload because it may crash the system. Denial of Service http://www.sapido.com.tw/...
Page 17
VPN Server PPTP/L2TP general setup introduction. NAT Management There are port forwarding and DMZ function Remote management This page allow you to access the GUI on WAN. Advance Setup Advance setting menu Time Zone You can maintain the system time by synchronizing with a public time server over the Internet.
Click Internet Setup icon to enter WAN setup as below. The Int ernet Setup is depended on the servic e that you contract with the provider. The BRF70N provides five selections for the Internet Mode type, PPPoE, DHCP, Static IP , PPTP and L2TP and WiFi ISP. Check with your ISP if you don’t know the WAN type.
3.3.1 PPPoE Item Description User Name Input your us er name provided by your ISP. If you don’t know, please check with your ISP. Password Input the password provided by your ISP. Wireless AP Turn on/ off wireless SSID Service S et identifier, users can define to any or keep as default. Encryption Select wireless encryption type form the drop-down list.
Page 20
Item Description MAC type Select "Universal” or “Specific" Universal:clone controller PC mac address as BRF70n WAN mac address Specific:use BRF70n itself mac address Wireless AP Turn on/ off wireless SSID Service S et identifier, users can define to any or keep as default.
3.3.3 Static IP Item Description IP Address Enter the IP address which is provided by your ISP. Subnet Mask Please enter the Subnet Mask address Gateway Input ISP Default Gateway Address. Input DNS information which is provided by your ISP Wireless AP Turn on/ off wireless SSID...
Page 22
Item Description Addre ss Mode Select "Dynamic" or "Static" IP Address Input your IP address or domain name Gateway Input ISP Default Gateway Address. Server IP Address Input your server IP address provided by your ISP. If you don’t know, please check with your ISP. User Name Input PPTP account provided by your ISP.
SSID Service S et identifier, users can define to any or keep as default. Encryption Select wireless encryption type form the drop-down list. 3.3.5 L2TP Item Description Addre ss Mode Select "Dynamic" or "Static" IP Address Input your IP address or domain name Gateway Input ISP Default Gateway Address.
3.3.6 WiFi ISP BRF70n WAN get IP address from other wireless AP and LAN/Wireless LAN client get IP from BRF70n. Item Description Survey List all available wireless AP Pre-Shared Key Input the wireless AP key which you want to connect...
Item Description Wireless AP Turn on/ off wireless SSID Service S et identifier, users can define to any or keep as default. Encryption Select wireless encryption type form the drop-down list. Wireless AP Turn on/ off wireless WiFi AP ( switch to WiFi AP mode) When you connect to the internet wirelessly through PC and wireless device without WAN、DHCP、NAT、...
Page 26
http://www.sapido.com.tw/ User Manual v1. 0.0...
Chapter 4 GUI Function Setup Status You could check WAN, LAN, Client net work in status. WAN Configuration http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 28
LAN Configuration http://www.sapido.com.tw/ User Manual v1. 0.0...
Client Configuration Allow or block client to access internet Parental Control Control Parental provide URL Filtering and MAC Filter Schedule for setup 4.2.1 URL Filtering URL Filtering is used to restrict users to access specific websites in internet http://www.sapido.com.tw/ User Manual v1. 0.0...
Item Description Enable URL Filtering Please select Enable MAC Filtering to filter MAC addresses URL Address Please enter the MAC address that needs to be filt ered. Apply Click on Apply to save the setting data. Current Filter Table It will display all ports that are filt ering now. Delete Selected &...
Item Description Enable MAC Filtering Please select Enable MAC Filtering to filter MAC addresses. 4.2.3 Wireless Schedule Wireless available schedule, this page allows you setup the wireless schedule rule. Please do not forget to configure systeim before enable this feature http://www.sapido.com.tw/ User Manual v1.
Office Control Office control provide Multiple AP 、Wireless Access Control、IP Filtering、IP Binding、QoS 4.3.1 Multiple AP http://www.sapido.com.tw/ User Manual v1. 0.0...
The BRF70n can register up to 4 SSIDs (wireless LAN group). It can be used as if there are multiple wireless LAN access points with one product. Item Description Enable Enable or disable the service. SSID Enter the SSID Data Rate Select the data transmission rate.
4.3.3 IP Filtering When enabled, LAN clients are blocked / filtered from accessing the Internet based on their IP addresses Item Description Enable IP Filtering Please select Enable IP Filtering to filter IP addresses. Local IP Address Please enter the IP address that needs to be filtered. Protocol Please select the protocol type of the IP address Apply...
Item Description Enable Static DHCP Select enable to use Static DHCP function IP Address Please enter IP address to limit MAC addre ss Please enter MAC address to limit Static DHCP Li st It will display all IP and MAC address you made. Delete Selected &...
Item Description Enable QoS Check “Enable QoS” to enable QoS function for the WAN port. You also can uncheck “Enable QoS ” to disable QoS function for the WAN port. Manual Uplink Speed Set the uplink speed by manual to assign the download or upload bandwidth by the unit of Kbps.
This function can upgrade the firmware of the router. There are two methods for user upgrade firmware: Auto upgrade and Manual upgrade. Caution: To prevent that firmware upgrading is interrupted by other wireless signals and causes failure. We recommend users to use wired connection during upgrading. Note : The firmware upgrade will not remove your previous settings.
Page 38
Home: Item Description Home Home Check “ ” to enable DoS function for prevention. You also can No Prevention check “ ” to disable DoS function. Enterprise: http://www.sapido.com.tw/ User Manual v1. 0.0...
Item Description Enterprise Enterprise Check “ ” to enable DoS function for prevention. You also No Prevention can check “ ” to disable DoS function. VPN Server The VPN Server function providing PPTP/L2TP mode are designed to allow users to an external network device / computer and office local area network to establish a secure network connection.
Click Delete Selected will delete the selected item. Click Delete All will delet e all items in this table. NAT Management This section contains configurations for the BRF70N ’s advanced functions such as: virtual server, and DMZ to provide your network under a security environment. http://www.sapido.com.tw/...
4.7.1 Virtual Server The Virtual Server feature allows users to create Virtual Servers by re-directing a particular range of service port numbers (from the WAN port) to a particular LAN IP address. Item Description Enable Port Forwarding Select to enable Port Forwarding service or not. Addre ss Specify the IP address which receives the incoming packets.
will delet e all items in this table. Please find the following figure to know that what the virtual server is. The web server is located on 192.168.1.100, forwarding port is 80, and type is TCP+UDP. 4.7.2 The DMZ feature allows one local user to be exposed to the Internet for special-purpose applications like Internet gaming or videoconferencing.
Remote Management This page allows you to access the GUI on WAN. Item Description HTTP Connection Port Users can access GUI by this port,default is 80 Enable Web Server Access Allow user access GUI from WAN side on WAN Time Zone Users can select time zone and synchronize the local clock on the router.
Chapter 5 Advance Setup Internet Mode 5.1.1 Internet Setup Please refer Internet Setup AP(switch to AP mode) 5.1.2 Please refer WiFi AP(switch to WiFi AP mode) 5.1.3 Please refer WiFi AP 5.1.4 WiFi ISP Please refer WiFi ISP IP Config 5.2.1 5.2.1.1 PPPoE...
Page 46
Item Description User Name Input your us er name provided by your ISP. If you don’t know, please check with your ISP. Password Input the password provided by your ISP. Service Name Input the service name provided by your ISP. Connection Type Three types for select: Continue s, Connect on Demand, and Manual.
Save & Apply Click on Save to save the setting dat e, the Apply button for execute current configuration. 5.2.1.2 DHCP Item Description Host Name You can keep the default as the host name, or input a specific name if required by your ISP. MTU Size Maximum Transmission Unit.
Item Description IP Address Enter the IP address which is provided by your ISP. Subnet Mask Please enter the Subnet Mask address Gateway Input ISP Default Gateway Address, . MTU Size Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually. Input DNS information which is provided by your ISP Clone Mac Address Some ISPs require MAC address registration.
Page 49
Item Description Server IP Address Input your server IP address provided by your ISP. If you don’t know, please check with your ISP. User Name Input PPTP account provided by your ISP. Password Input the password provided by your ISP. MTU Size Maximum Transmission Unit.
you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C Address"...
ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C Address" Save & Apply Click on Save to save the setting dat e, the Apply button for execute current configuration.
and ex pired time. The default range is 192.168.1.100 - 192.168.1.200. DHCP Lease Time IP avaliable time Static DHCP Please refer IP Binding Domain Name The name of device 802.1d Spanning Tree IEEE 802. 1d Spanning Tree Protocol (STP) is a link layer network protocol t hat ensures a loop-free topology for any bridged LAN.
DynDNS, TZO, ChangeIP, Eurodns, OVH, NO-IP, ODS, Regfish BRF70N embedded in User Name/Email User name is used as an identity to login Dynamic-DNS service. Password/Key Password is applied to login Dynamic-DNS servic e. Save & Apply Click on “Save” to save the setting data. The “A pply” button can...
SLAAC、DHCPv6、IP。Please check ISP to get correct type Origin Type PPPoE、IP WAN Link Type Use IPv4 PPPoE account and password to do IPv6 connect PPPoE Check ISP to get this data Child Prefix Address Check ISP to get IP address and default gateway IP address Static IP Router domain Router Name...
Page 55
Item Description Di sable Wireless Turn off the wireless service. Band Select the frequency. It has 6 options: 2.4 GHz (B/G/N/B+G/G+N/B+G+N). Mode Select the mode. It has 3 modes to select: (AP, Client, WDS, AP+WDS). http://www.sapido.com.tw/ User Manual v1. 0.0...
While linking the upper level device in wireless way, you can set SSID to give the bottom layer user search. BRF70n can register up to 4 SSIDs (wireless LAN group). Multiple AP It can be used as if there are multiple wireless LAN access points with one product.
Page 57
Item Description Fragment Threshold To identify the maxima length of packet, the over length packet will be fragmentized. The allowed range is 256-2346, and default length is 2346. RTS Thre shold This value should remain at its default setting of 2347. The range is 0~2347.
Short GI Users can get better wireless transmission efficiency when they enable this function. Shut down th e communication betw een th e connected WLAN Partition wireless LAN de vices. If you set up as "Ena ble d", devices connected with the router, suc h as a pr inte r, wi ll not be a ble to use.
Access Point in a minute without any hassle. SAPIDO BRF70N could support both Self-PIN or PBC modes, or use the WPS button (at real panel) to easy enable the WPS function.
Page 60
PBC model, in which the user simply has to push a button, either an actual or a virtual one, on both WPS devices to connect. BRF70n WPS only support no encryption and WPA2 Please follow instructions below to enable the WPS function.
(4). Wireless dongle should connect to BRF70n Start PBC: (1). Press the BRF70n WPS button and wait for WPS LED blinking (2). Press the dongle WPS button (3). Wireless dongle should connect to BRF70n 5.4.6 When selected in the Basic Settings page and enabled here, Wireless Distribution System (WDS) enables the router to be used as a wireless bridge.
Page 62
Please check the MAC address Enable WDS function from the page – “WDS Setting”, and then fill in the MAC address of Router_B. Click Apply Changes to save the setting data. http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 63
Select encryption for security Rout er_B mac address The WDS AP List will show the WDS device MAC address. Router_B: Setup Router_B WDS. Select encryption for security Rout er_A mac address http://www.sapido.com.tw/ User Manual v1. 0.0...
Router_B LAN PC will get IP address from Router_A. If you failed the WDS setting, please check you setting with refer to the list below. Router_A Router_B Wireless Mode AP+WDS LAN IP Address Set the same segment as the Set the same segment as the router B(Note 1) router_A (Note 1)
VPN Server Please refer VPN server Firewall 5.7.1 Please refer 5.5.2 Item Description Enable QoS Check “Enable QoS” to enable QoS function for the WAN port. You also can uncheck “Enable QoS ” to disable QoS function for the WAN port.
Manual Uplink speed Input uplink bandwidth manually Automatic downlink Check the Automatic downlink speed. speed Manual Downlink speed Input downlink bandwidt h manually Addre ss Type Set QoS by IP Address or MAC address Local IP Address Set local IP Address if the address type is by IP Address MAC Addre ss Set MAC Address if the address type is by MAC Address Mode...
Item Description Forwarding Rule Bridge or NAT mode Add VLAN tag to packet Set VLAN ID(1~ 4096) Priority It indicates the frame priority level. Values are from 0 (best effort) to 7 (highest); 1 represents the lowest priority Enable or Disable CIF 5.6 System This section including Wake on LAN, Change Username/Password, Upgrade Firmware, Profiles Save, Remote Management, Time Zone, UPnP, Route Setup, VPN Passthrough,...
5.6.4 Change User name/Password Users can set or change user name and password used for accessing the web management interface in this section. Input User Name and New Password, then input Confirm Password again. 5.6.5 Upgrade Firmware Please refer Firmware Upgrade 5.6.6 Profiles Save Users can create a backup file that contains current router settings.
Page 70
(2). Please click “Save” to save the configuration to your computer. (3). Select the location which you want to save file, then click Save. Load configuration file (1). Tap “browse” and select configuration file then click Open http://www.sapido.com.tw/ User Manual v1. 0.0...
(2). Click Upload to upload configuration file to BRF70N . (3). After 60 seconds, BRF70N will reboot automatically. 5.6.7 Remote Management Please refer Remote Management 5.6.8 Time Zone Users can synchronize the local clock on the router to an available NTP server (optional).
(data sharing, communications, and entertainment) and in corporate environments for simplified installation of computer components. BRF70N supports UPnP function, and can cooperate with other UPnP devices. When you activate UPnP, please click My Network Places. Users will see an Internet Gateway Device icon.
5.6.10 Route Setup Dynamic routing is a distance-vector routing protoc ol, which employs the hop count as a routing metric. RIP prevents routing loops by implementing a limit on the number of hops allowed in a path from the source to a destination. The maximum number of hops allowed for RIP is 15 Static routing is a data communication concept describing one way of configuring path selection of rout ers in computer networks.
Item Description Enable Static Route Enable or Disable dy namic route IP Address Destination IP address Subnet Mask Destination IP subnet mask Gateway Gateway IP address for destination Metric Metric number on router’s routing table Interface Static route rule for LA N or WAN interface 5.6.11 VPN Passthough Virtual Private Networking (VP N) is typically used for work-related net working.
A: There are two ways to know. Way 1: Check with your Internet Service Provider. Way 2: Check the setting screen of BRF70N . Click on Status & Log item to select Network Configuration on the Main Menu. WAN IP is shown on the WAN interface.
A: Yes, the Router mode allows for customization of your public IPs and Domain. 6.4 OS Setting Why can’t my computer work online after connecting to BRF70N ? A: It’s possible that your Internet protocol (TCP/IP) was set to use the following IP address.
Q: Why does BRF70N ’s setup page shut down unexpectedly? A: If one of the pages appears incompletely in BRF70N ’s setup pages, please click on Logout item on the Main Menu before shutting it down. Don’t keep it working. Then, close Internet browser and open it again for going back to the previous page.
6.6 Wireless LAN Q: Why couldn’t my wireless notebook work on-line after checking? A: Generally, Wireless networks can sometimes be very complicated to set up, particularly if you're dealing with encryption and products from different vendors. Any number of variables can keep your workstations from talking to each other. Let's go over some of more common ones.
Page 80
A: The default WEP of WinXP is Authentication Open System - WEP, but the WEP of SAPIDO BRF70N is only for Shared Key - WEP, it caused both sides couldn’t communicate. Please select the WEP of WinXP from Authentication Open System to Pre-shared Key - WEP, and then the WEP wireless interface between WinXP and SAPIDO BRF70N would be communicated.
6.7 Support Q: What is the maximum number of IP addresses that the XDSL Router will support? A: The Router will support to 253 IP addresses with NAT mode. 5. Q: Is the Router cross-platform compatible? A: Any platform that supports Ethernet and TCP/IP is compatible with the Router. 6.8 Others Q: Why does the router dial out for PPPoE mode very often? A: Normally some of game, music or anti-virus program will send out packets that...
Chapter 7 Appendices 7.1 Operating Systems Microsoft:Windows 2000, XP, Vista, Windows 7. Apple:Mac OS X 10.4.7, Leopard and the following related versions. Linux:Redhat 9, Fedora 6 & 7, Ubuntu 7.04 and the following related versions. 7.2 Browsers Internet Explorer ver. 6 and 7 and the following related versions. FireFox ver.