Table of Contents
Advertisement
Quick Links
Advertisement
Chapters
Table of Contents
Related Manuals for IBASE Technology IP400
Summary of Contents for IBASE Technology IP400
- Page 1 IP400 ETX Baseboard USER’S MANUAL Version 1.0...
- Page 2 Intel and Pentium M are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation. All other product names or trademarks are properties of their respective owners. IP400 User’s Manual...
-
Page 3: Table Of Contents
Table of Contents Introduction ............1 IP400 Specifications............1 Board Dimensions ............... 2 Installations ............3 Installing the CPU Module..........4 Setting the Jumpers ............. 5 Connectors on IP400 ............8 IP400 User’s Manual... - Page 4 The IP400 Baseboard IP400 User’s Manual...
-
Page 5: Introduction
INTRODUCTION Introduction IP400 Specifications Product Name IP400 (for COM ETX module) Form Factor Flex ATX for COM ETX CPU module Lithium Battery for real time clock Battery Audio Derived from COMETX Module AC97 Codec ALC655 w/ 6 channels (Line-out, Line-in, Mic.) + NS LM4940 8ohm 2W stereo... -
Page 6: Board Dimensions
INTRODUCTION Board Dimensions IP400 User’s Manual... -
Page 7: Installations
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the IP400 in order to set up a workable system. The topics covered are: Installing the CPU Module..........4 Setting the Jumpers ............. 5 Connectors on IP400 ............8... -
Page 8: Installing The Cpu Module
ET810. Below is a picture showing how the CPU module and the heatsink should be installed on the IP400 baseboard. There are five holes on the IP400 that can be used to screw the three parts together – the heatsink, the CPU module and the baseboard. -
Page 9: Setting The Jumpers
INSTALLATIONS Setting the Jumpers Jumpers are used on IP400 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on IP400 and their respective functions. - Page 10 INSTALLATIONS Jumper Locations on IP400 Jumpers on IP400 ................Page Jumper Locations on IP400 ..............6 JP2, JP3, JP4: ATX Power On Control ..........7 JP5: CompactFlash Slave/Master Selection........... 7 JP6: LCD Panel Power Selection ............7 IP400 User’s Manual...
- Page 11 JP2, JP3, JP4: ATX Power On Control JP2, JP3 ATX Power On Control With LPC I/O With COM Express’ Southbridge JP5: CompactFlash Slave/Master Selection CF Setting Master Slave JP6: LCD Panel Power Selection LCD Panel Power 3.3V IP400 User’s Manual...
-
Page 12: Connectors On Ip400
INSTALLATIONS Connectors on IP400 The connectors on IP400 allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on IP400 and their respective functions. Connector Locations on IP400 ............9 CN2: PS/2 Keyboard and PS/2 Mouse Connectors ...... -
Page 13: Connector Locations On Ip400
INSTALLATIONS Connector Locations on IP400 IP400 User’s Manual... -
Page 14: Cn2: Ps/2 Keyboard And Ps/2 Mouse Connectors
Keyboard Mouse Signal Name Keyboard data Mouse data N.C. N.C. Keyboard clock Mouse clock N.C. N.C. J8: S-Video and RCA Connectors CN3: COM1 and VGA Connector Signal Name Pin # Pin # Signal Name COM1 Not Used IP400 User’s Manual... -
Page 15: Cn6: 10/100 Rj-45 And Usb1/2 Ports
PD2, parallel data 2 Select PD3, parallel data 3 Ground PD4, parallel data 4 Ground PD5, parallel data 5 Ground PD6, parallel data 6 Ground PD7, parallel data 7 Ground ACK, acknowledge Ground Busy Ground Paper empty Ground Select IP400 User’s Manual... -
Page 16: Fdd1: Floppy Drive Connector
Host data 15 Ground Protect pin DRQ0 Ground Host IOW Ground Host IOR Ground IOCHRDY Host ALE DACK0 Ground IRQ14 No connect Address 1 No connect Address 0 Address 2 Chip select 0 Chip select 1 Activity Ground IP400 User’s Manual... -
Page 17: Fan1: Cpu Fan Power Connector
Signal Name OUT3 OUT1 OUT2 OUT0 J3: ATX_12V Connector J3 can be used in situations where the 12V current from the ATX power is insufficient to supply needed current. Pin # Signal Name Ground Ground +12V +12V IP400 User’s Manual... -
Page 18: J4: Atx Power Supply Connector
RXD, Receive data RTS, Request to send TXD, Transmit data CTS, Clear to send DTR, Data terminal ready RI, Ring indicator GND, ground Not Used J6: IrDA Connector Pin # Signal Name No connect Ir RX Ground Ir TX IP400 User’s Manual... -
Page 19: J7: Tv Out (Df11)
The LVDS connectors on board consist of the first channel (J13) and second channel (J14). Signal Name Pin # Pin # Signal Name TX0- TX0+ Ground Ground TX1- TX1+ 5V/3.3V Ground TX3- TX3+ TX2- TX2+ Ground Ground TXC- TXC+ 5V/3.3V ENABKL +12V +12V IP400 User’s Manual... -
Page 20: J17: Line Out / Mic Header
TXD, Transmit data CTS, Clear to send DTR, Data terminal ready RI, Ring indicator GND, Ground Not used PCIE_1: 16-line PCI-Express Connector PCIE_2: 1-line PCI –Express Connector PCI1, PCI2: PCI Slots J10, J11: COM Express Type 2 Connectors IP400 User’s Manual... - Page 21 APPENDIX IP400 User’s Manual...