Directed Electronics 671XV Installation Manual
  1. Manuals
  2. Brands
  3. Directed Electronics Manuals
  4. Car Alarm
  5. 671XV
  6. Installation manual
Directed Electronics 671XV Installation Manual

Directed Electronics 671XV Installation Manual

Car security
Hide thumbs
Table of Contents

Advertisement

Quick Links

M M o o d d e e l l 6 6 7 7 1 1 X X V V
I I n n s s t t a a l l l l a a t t i i o o n n G G u u i i d d e e
NOTE:
This product is intended for installation by a professional installer only!
Any attempt to install this product by any person other than a trained professional
may result in severe damage to a vehicle's electrical system and components.
© 2004 Directed Electronics, Inc. Vista, CA
N437V 05-04

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 671XV and is the answer not in the manual?

Questions and answers

Related Manuals for Directed Electronics 671XV

Summary of Contents for Directed Electronics 671XV

  • Page 1: T T R R A A N N S S M M I I T T T T E E R R / / R R E E C C E E I I V V E E R R L L E E A A R R N N R R O O U U T T I I N N E

    This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result in severe damage to a vehicle’s electrical system and components. © 2004 Directed Electronics, Inc. Vista, CA N437V 05-04...
  • Page 2 ® Registered Trademarks of Directed Electronics, Inc. w w w w w w . . d d i i r r e e c c t t e e c c h h s s . . c c o o m m D D i i r r e e c c t t F F a a x x 8 8 0 0 0 0 - - 9 9 9 9 9 9 - - 1 1 3 3 2 2 9 9 T T e e c c h h n n i i c c a a l l S S u u p p p p o o r r t t 8 8 0 0 0 0 - - 7 7 5 5 3 3 - - 0 0 8 8 0 0 0 0 These resources are for authorized Directed Dealer use only.

  • Page 3: Table Of Contents

    W W i i r r i i n n g g Q Q u u i i c c k k R R e e f f e e r r e e n n c c e e G G u u i i d d e e ........................................2 2 8 8 © 2004 Directed Electronics, Inc.

  • Page 4: P P R R I I M M A A R R Y Y H H A A R R N N E E S S S S ( ( H H 1 1 ) ) W W I I R R E E C C O O N N N N E E C C T T I I O O N N G G U U I I D D E

    NOTE: If using the H1/1 ORANGE wire to activate an add-on accessory such as window automation, pager or voice module a 1Amp diode must be installed to ensure proper operation. Insert the diode as shown in the following diagram. IMPORTANT! Never interrupt any wire other than the starter wire. © 2004 Directed Electronics, Inc.

  • Page 5: M M U U L L T T I I - - L L E E V V E E L L S S E E C C U U R R I I T T Y Y A A R R M M I I N N G

    H1/3 WHITE/BLUE 200 mA (-) channel 3 output This wire provides a (-) 200 mA output whenever the transmitter button(s) controlling Channel 3 © 2004 Directed Electronics, Inc.
  • Page 6 Connect the H1/4 wire to the optional domelight supervision relay as shown in the following diagram: IMPORTANT! This output is only intended to drive a relay. It cannot be connected directly to the domelight circuit, as the output cannot support the current draw of one or more bulbs. © 2004 Directed Electronics, Inc.
  • Page 7 (+)12V when any door is opened. This wire will report Zone 3. NOTE: If using a door trigger wire that has a delay, Advanced Menu 2, feature 6, or the 998T Bitwriter can be used to turn Bypass Notification off. © 2004 Directed Electronics, Inc.
  • Page 8 H1/10 BROWN (+) siren output Connect this to the RED wire of the Revenger® siren. Connect the BLACK wire of the siren to (-) chassis ground, preferably at the same point you connect the control module’s BLACK ground wire. © 2004 Directed Electronics, Inc.

  • Page 9: D D O O O O R R L L O O C C K K H H A A R R N N E E S S S S ( ( H H 2 2 ) ) , , 3 3 - - P P I I N N C C O O N N N N E E C C T T O O R

    For detailed instructions about connecting to the vehicle’s power door lock systems, refer to the Door Lock Wiring guide (Document No. 1041) available to authorized dealers only from the technical resources listed at the front of this guide. © 2004 Directed Electronics, Inc.

  • Page 10: Super Bright Led, 2-Pin White Plug

    Check for rear clearance before drilling a 9/32-inch hole and mounting the button.The GRAY wire in the two-pin plug may also be used as a (+) ghost switch input and can be connected to any (+) switch in the vehicle. (See Feature Descriptions section of this guide.) © 2004 Directed Electronics, Inc.

  • Page 11: Programmer Interface, 3-Pin Black Plug

    NOTE: If installing an optional Directed dual-stage sensor, connect to the GREEN wire. The following diagram eliminates the need for diodes to isolate the sensors, as well as providing a separate zone for each sensor. © 2004 Directed Electronics, Inc.
  • Page 12 RED (+) 12V Constant and BLACK (-) Ground Do not use these for anything besides the plug-in shock sensor. NOTE: If adding additonal sensor(s), connect the power and ground of the additional sensor(s) to the power and ground at the 12-pin harness. © 2004 Directed Electronics, Inc.

  • Page 13: Light Flash Jumper

    IMPORTANT! DO NOT connect the H1/2 light flash wire to a negative vehicle light flash wire before changing the programming jumper to the negative polarity position or damage to vehicle light circuit may occur. © 2004 Directed Electronics, Inc.

  • Page 14: Bypassing Sensor Inputs

    H1/6 BLUE wire, all trigger inputs except the door trigger input will remain bypassed until five seconds after ground is removed from the BLUE wire. This can be done using the status output of a Directed Electronics remote engine starting unit as shown in the following diagram: System Features Learn Routine The System Features Learn Routine dictates how the unit operates.
  • Page 15 6. R R e e l l e e a a s s e e t t h h e e V V a a l l e e t t / / P P r r o o g g r r a a m m S S w w i i t t c c h h . . Once a feature is programmed: Other features can be programmed within the same menu. Another menu can be selected. The learn routine can be exited if programming is complete. © 2004 Directed Electronics, Inc.
  • Page 16 Menu #2. To exit the learn routine do one of the following: Close the open door. Turn the ignition on. No activity for longer than 15 seconds. Press the Valet/Program switch too many times. © 2004 Directed Electronics, Inc.

  • Page 17: Menu #1 - Basic Features

    Ignition-controlled domelight OFF Single unlock pulse Double unlock pulse Channel 3: Validity Channel 3: latched/latched, reset with ignition/30-second timed/ second unlock output* *Second unlock is only available if Feature 2-8 is programmed to single pulse. © 2004 Directed Electronics, Inc.

  • Page 18: Menu #1 - Basic Features

    Audi, require longer lock and unlock pulses to operate the vacuum pump. Programming the system to provide 3.5 second pulses, will accommodate the door lock interface in these vehicles. The default setting is 0.8 second door lock pulses. © 2004 Directed Electronics, Inc.

  • Page 19: Menu #2 - Advanced Features

    If one zone is triggered three times in one hour, that zone is bypassed for one hour, starting from the time of the third trigger. During that hour, if the system detects a © 2004 Directed Electronics, Inc.
  • Page 20 SECOND TIMED/SECOND UNLOCK OUTPUT: Channel 3 can be programmed for these output configurations. The unit is set to the default validity output. To change the configuration, use the two-chirp setting to toggle to the different configurations. © 2004 Directed Electronics, Inc.
  • Page 21 Remote Start or other accessories WHITE/BLUE Arm only Disarm only Panic only Auto-learn Standard Configuration* Auto-learn Single Button Arm/Disarm Configuration* Delete all transmitters *NOTE: For Auto Learn Configurations, see Transmitter Configurations section of this guide. © 2004 Directed Electronics, Inc.
  • Page 22 One long chirp indicates that Learn Routine has been exited. Learn Routine will be exited if any of the following occurs: Ignition is turned off. Door is closed. Valet/Program button is pressed too many times. More than 15 seconds elapse between steps. © 2004 Directed Electronics, Inc.

  • Page 23: Standard Configuration

    Single Button Arm/Disarm Configuration When programmed for single button arm/disarm configuration, the transmitter buttons are assigned to the following functions: operates Arm/Disarm/Panic operates Channel 2 and Silent Mode operates Channel 3 © 2004 Directed Electronics, Inc.

  • Page 24: Arm/Disarm Diagnostics

    0.8 seconds will trigger a Warning Zone response, while inputs longer than 0.8 seconds will instantly trigger the full alarm sequence. Two-stage (similar to doors) Ignition input. H1/9 YELLOW. NOTE: The Warn Away® response does not report on the LED. © 2004 Directed Electronics, Inc.

  • Page 25: Long Term Event History

    VRS is an optional feature designed to disable a vehicle during a carjacking event. It must be programmed in the features menu and the Failsafe Starter Kill must be installed for it to work properly. For operational instructions when testing VRS refer to the Owner's Guide. © 2004 Directed Electronics, Inc.

  • Page 26: Rapid Resume Logic

    Closing the door triggers the system, but opening the door does not. Have you correctly identified the type of door switch system? This happens often when the wrong door input has been used. © 2004 Directed Electronics, Inc.
  • Page 27 Is it plugged into the correct socket? Check the System Features Learn Routine for the programmed Valet pulse count. Status LED doesn’t work. Make sure that it is plugged in. (See Plug-In Harnesses section of this guide.) Is the LED plugged into the correct socket? © 2004 Directed Electronics, Inc.

  • Page 28: Wiring Quick Reference Guide

    Wiring Quick Reference Guide © 2004 Directed Electronics, Inc.

This manual is also suitable for:

690xv

Table of Contents