Table of Contents
Advertisement
Quick Links
Mini Portable Wireless NVR System
IP Network Camera with USB Receiver
Warranty
The warranty is for one year from the date of purchase. During the one-year
warranty period, the product is eligible for replacement in case of defects in
material and workmanship. In such cases, the defective unit will be repaired or
replaced by the manufacturer.
This warranty does not cover damages caused by improper use or from
unauthorized modifications by third parties. In addition, this warranty does not
cover expendable materials and defects, which constitute as normal wear and
tear.
USER'S MANUAL
©
Copy Right
IA Technologies
Copy Right
©
IA Technologies
Webpage :
www.iat101.com
;
www.ia-tecs.com
Advertisement
Table of Contents
Related Manuals for IAT Mini Portable Wireless NVR System
Summary of Contents for IAT Mini Portable Wireless NVR System
- Page 1 Mini Portable Wireless NVR System IP Network Camera with USB Receiver Warranty The warranty is for one year from the date of purchase. During the one-year warranty period, the product is eligible for replacement in case of defects in material and workmanship. In such cases, the defective unit will be repaired or replaced by the manufacturer.
- Page 2 The antennas used for this transmitter must be installed to provide a separation Federal Communication Commission Interference Statement distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
-
Page 3: Safety Caution
Safety Precautions CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN! CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ** It is advised to read the Safety Precaution Guide through carefully before operating the product, to prevent any possible danger. -
Page 4: Table Of Contents
About This Manual 1-- Getting started This manual is designed to assist users to operate the Wireless IP USB Camera – Congratulations on your purchase of the network camera system. Use this system (read carefully). Information in this document has been carefully checked for to monitor locations wireless, as stand-alone solution. -
Page 5: Usb Receiver
Identifying Parts PC System Requirements Refer to the following section to identify components of the camera and receiver. CPU: Pentium 1.6 GHz or higher (recommended) RAM: 512 MB or higher (recommended) USB Receiver Network: Ethernet Port Resolution: 800 x 600 or 1024 x 768 (recommended) Operating Software: Windows 2000, XP, Vista or Window 7 Windows Media Player 9 or higher (recommended) One available USB port... -
Page 6: 2- Setting Up
- Ceiling / Wall installation 2-- Setting Up . Fix the camera to the wall or ceiling using the bracket supplied. . The bracket used must fit securely in the mounting socket to ensure proper This section explains the mounting options and setup of the installation. -
Page 7: Power Supply
Power Supply 3. Click “Finish” to complete the software installation. Connect the Power Adapter Connect one end of the AC adapter to the DC IN jack of the camera the other end to the wall outlet. Make sure power plug is pushed all the way in. When the software is well installed, you can find on the Battery Recharge... -
Page 8: 3- Operation
3-- Operation This icon indicates that the camera is monitoring mode This icon indicates that the camera is in standby Viewing Page This icon indicates that the camera is recording Insert the USB Receiver to one USB port of PC and double-click This icon indicates that the camera’s audio is enabled on the desktop, the viewer screen will display as shown below Option Menu:... -
Page 9: Pairing
Channel Information: Displays the current channel’s information Pairing 1. Make sure the camera is turned on, the power LED of the camera will Blink if it is power 2. Click for match setting, select a camera which you want to match, then press and hold the pairing button on the side of the camera for about 6 seconds. -
Page 10: System Setting
6. Web Service: Configuration settings for the web server System Setting Network status such as current IP and related details are clearly shown. Press “web server” icon of the main screen to enter “System Setting”. IP address: The IP address of the web service for the viewer This section covers the main setup of the network camera system This system will log automatically the IP location of where the current computers. -
Page 11: Remote Monitoring
Remote Monitoring When the correct IP address is set in the web service, press “web server” icon of Basic Settings main screen; then open the IE or Mozilla Firefox browser to input http://IP This section of the wireless network camera system viewer allows users to address:7788, will appear the below dynamic image;... -
Page 12: Image Adjust
Image Adjust Record Setting If the camera is mounted in a special way, the section can adjust the image This section sets up how recording will be performed under recording mode. accordingly. Image Quality: Adjust the quality of the recording format Choose from the following to adjust image: Resolution: Adjust the recording image size Flip Horizontal: Flips the image horizontally... - Page 13 Select Daily Schedule Base: If “Schedule” is chosen from mode, user can preset a time to record. Add new Schedule: To add a schedule Select the icon “recording”, and click “Add new Schedule”, then appear the below images Select Periodically 1.
- Page 14 Select Weekly Select Monthly 1. Choose the start time of Scheduling Type “Monthly” 1. Choose the start time of Scheduling Type “Weekly” 2. Choose the end tine of Scheduling Type “Monthly” 2. Choose the end time of Scheduling Type “Weekly” 3.
-
Page 15: Motion Detect
a. Full-area detection: Detects all areas on the screen Motion Detect This section will be available if the recording is set to “Triggered”, this particular area allows users to customize sections of detection and the sensitivity. b. Custom detection: Detects user created detection blocks Add new area: Select the icon “Add new Area”... -
Page 16: Alert Setting
Press the “Playback“ on the main screen Alert Setting This section will be available if the recording option is set to “Triggered”, this particular area allows the user to set notification options in the even the viewer detects motion. 1. Main display screen: This area will display the video output from the recording 2. -
Page 17: Appendix
bad network setup, make sure that your network is configured correctly. Appendix What does “Can not import to the following channel(s): CH**” mean? This appendix describes cleaning and troubleshooting procedures. Also It means that another web server is conflicting with another IP address. covered are technical specifications, and warranty information. - Page 18 Edition 1st Edition Copyright This publication contains information that is protected by copyright. No part of it may be reproduced, transmitted, transcribed, stored in a retrieval WEEE Directive & Product Disposal system, or translated into any language without permission from the copyright holders.