Turn Area On/Off; Turn All Areas On; Turn All Areas Off; Move To Area - Vision -64 User Manual

14 Vision-64 User Guide
Areas > Commands >

Turn Area On/Off

This menu allows you to turn an area All On or off.
1. Enter [MENU] + [2] + [0] + [1].
A list of different areas will display on the keypad.
A001 Reception Area
A002 Sales Dept 
A003 Administration Dept
Press , OK or MENU

If an area has already been turned All On or Part On, a
'tick' () will be displayed on the right side of the name
description (see A002 Sales Dept above).
2. Use the [↑] and [↓] keys to select the area that you want to
turn on or off, then press [OK] to select. Alternatively, you
can enter the area number you want to turn on or off, then
press [OK].
Areas > Commands >

Turn All Areas On

This menu allows you to turn on all areas that your PIN has been
assigned to at the same time All On. The keypad display below
shows the area icons 1 through to 8.
1. Enter [MENU] + [2] + [0] + [2].
The keypad will display the exit time bar to prompt you to
exit all areas. You should leave all areas now.
Area 1 Name
EXIT NOW
When exit time has expired, the keypad will display that all
areas are turned All On (Armed).
Area 1 Name
Fri,Aug,13 5:34 pm
Note:
Area icons will only display if programmed to
do so by your security installer.
Note: Area icons will only display if programmed to do
i
so by your security installer.
Issue 1.03
MENU 2-0-1
MENU 2-0-2
ARMED
Areas > Commands >

Turn All Areas Off

This menu allows you to turn off all areas that your PIN has been
assigned to at the same time. However, this menu requires at least
one area that has a keypad assigned to it to be disarmed before you
can access this command.
1. Enter [MENU] + [2] + [0] + [3].
Areas > Commands >

Move To Area

This menu allows you to operate multiple areas from the same
keypad when the system has been partitioned. Before operating a
different area, you will need to move the keypad to the area that
you want to operate.
1. Enter [MENU] + [2] + [0] + [4].
A list of different areas will display on the keypad.
A001 Reception Area
A002 Sales Dept
A003 Administration Dept
Press , OK or MENU

2. Use the [↑] and [↓] keys to select the area that you want
to move the keypad display to, then press [OK] to select.
Alternatively, you can enter the area number that you want
to move the keypad display to, then press [OK].
Areas > Commands >

Chime On/Off

Chime mode allows you to monitor a zone (or group of zones)
to sound the keypad buzzer or activate a programmable output
when the corresponding area is turned off (disarmed). This can
be useful when you need to monitor the front or back entrance to
the premises.
This menu allows a user to turn chime mode on or off. Only
keypads programmed to sound the chime tone will be heard when
a zone programmed for chime is faulted.
The master user can Set Chime Zones on page ????. This allows the
master user to program which zones can be monitored for chime.
1. Enter [MENU] + [2] + [0] + [5].
A list of different areas will display on the keypad.
A001 Reception Area 
A002 Sales Dept
A003 Administration Dept
Press

2. Use the [↑] and [↓] keys to select the area that you want
to turn chime mode on or off, then press [OK] to select.
Alternatively, you can enter the area number that you want
to turn chime mode on or off, then press [OK].
MENU 2-0-3
MENU 2-0-4
MENU 2-0-5
OK or MENU
Copyright © 2002-2005 Digflex Pty Ltd