NOTICE TO OWNER Thankyou for selecting the Vision Security Control Panel for your security needs. Your system includes many advanced features and functions which will be programmed and configured by your security consultant during installation. Depending on the configuration, and your access level, you may have the ability to program certain features within the system to suit changes in your security needs.
Area 1. The alarm system can be divided into 4 individual areas Automatic Test Reports running off the same Vision control panel. In this case, the security Built-In Telephone Line Fail Monitor company would assign different sensors (zones) to each area Securitel Compatible ...
Vision-64 User Guide Re p ort i n g A l a rms Description Your system may be programmed to send reports to your security The [] key allows you to navigate through company. Once the report is complete, the system returns...
Vision-64 User Guide Icon Status Meaning After you turn an area All On, the keypad will sound 1 short beep every second. During the last Exit The area is turned off. Delay 10 seconds fast short beeps will be heard. If you Tone don’t exit before the delay time expires and an...
TURNING AN AREA PART ON / PART 2 ON feedback. If you enter your PIN before the system dials your Use this function to turn an area Part On or Part 2 On. The Vision security company, the alarm report is cancelled (if programmed).
Vision-64 User Guide DTMF QUICK ARM PROGRAMMING TEXT USING THE KEYPAD If you forget to arm your system it may be possible for you to When programming text via the keypad, various keys on the keypad remotely arm it using a touch tone telephone if the remote arm operate differently.
Vision-64 User Guide Access > PIN Codes > Enter New PIN for Change Other PIN MENU 1-1-1 User 3 Name U003 If you have a master PIN, this command allows you to change somebody else’s PIN. It is recommended that you write down Press OK or MENU the old PIN and the new one before you begin.
Vision-64 User Guide TOKENS U001 JOHN SMITH This section outlines how to add and delete token cards that allow U002 DEBBIE SMITH an alternate method for users to turn the system on and off via a U003 USER 3 NAME prox reader enabled Keypad or an external reader.
Vision-64 User Guide Enter the RF Keyfob ID Number Access > User Properties > Press [OK] to save and exit, or press [MENU] to exit without Area Assignment MENU 1-4-1 saving. This menu allows the master user to program which areas (1 to 8) a user can access.
Vision-64 User Guide AREAS Access > User Properties > The Vision-64 control panel has the ability to be partitioned up Timer Group MENU 1-4-4 to 8 individual areas. This section outlines various commands that This menu is used to assign a User to a Timer Group. Timer control individual areas.
Vision-64 User Guide Areas > Commands > Areas > Commands > Turn All Areas Off MENU 2-0-3 Turn Area On/Off MENU 2-0-1 This menu allows you to turn off all areas that your PIN has been This menu allows you to turn an area All On or off.
The keypad will display the following when chime mode is INPUTS turned off: Each Vision-64 control panel has up to a maximum 64 zones. 16 zones are available as standard with an additional 48 wireless zones Reception Area A001 available when the optional radio received is fitted. Your installer...
Vision-64 User Guide Zone 1 Name Z001 is Zone 1 Name Z001 bypassed. To un-bypass, Zone Chime is ON. press OFF. To turn OFF, Press OFF. Press OK or MENU To Go Back Press OK Press [ON] or [OFF] to toggle the zone to be monitored If the zone is not bypassed, the keypad will prompt: when chime mode is turned on.
Vision-64 User Guide The keypad will scroll all zones that you can test. Inputs > Commands > Smoke Sensor Reset MENU 3-0-5 To test Z001 open/close This menu allows you to reset smoke sensors. Zone 1 Enter [MENU] + [3] + [0] + [5].
Vision-64 User Guide OUTPUTS Outputs > Commands > Each Vision-64 Vision control panel has up to a maximum of 8 Turn Output On/Off MENU 4-0-1 outputs. 4 outputs are available as standard with an additional 4 This menu allows you to turn outputs that have been programmed available when the optional output expander is fitted.
Vision-64 User Guide scroll through the different characters available. To clear all Internal Audible Testing text from the cursor position to the right, press the [OFF] Press any key to abort key. Press [OK] to save and exit, or press [MENU] to exit without saving.
If the user fails to acknowledge the call, the off-site computer for programming changes or updates. Your Vision control panel will make another attempt to report until the installer may request that you enter this command so that they can maximum number of call attempts are reached.
Comms > Periodic Test > saving. Send Test Report MENU 5-9-0 This menu allows you to test the reporting functions of the Vision control panel by manually sending a ‘Test’ report to the receiving party (i.e. security company monitoring station, mobile telephone etc).
Vision-64 User Guide If the test is successful, the keypad will prompt: Devices > Commands > X10 Status MENU 6-0-3 Communications Test Reserved Successful Devices > Commands > LAN P/Supply MENU 6-0-4 Reserved If the test is NOT successful, the keypad will prompt: Devices >...
The System Trouble Menu displays all current system troubles in a list format. Some trouble events require you to drill down and non- system trouble that are curent within the Vision control panel. Devices > Keypads > Contrast MENU 6-1-1 Press [MENU] + [7] + [0] + [1].
Vision-64 User Guide Press [MENU] + [7] + [0] + [2]. Zone 1 Name Z001 The keypad will display the most recent event stored in the EOL = Open history log. Press OK or MENU E001 Mon,01Oct 03:41 S1L2 Manual Test Report...
Vision-64 User Guide System > Schedules > System > Schedules > Name MENU 7-5-0 MENU 7-5-2 This menu allows you to program 16 characters of text for each This menu programs which days of the week the timer execute schedule name.
Vision-64 User Guide System > Holidays > System > System Testing > Start / Stop Day MENU 7-6-1 Walk Test All Zones MENU 7-9-0 This menu allows you to program the start date and the stop date This menu allows you to test all zones within an area at the same of each holiday period.
MENU 7-9-1 This menu allows you to manually test the systems back up battery. The Vision-64 will automatically test the battery once per day and every time the system is armed. The battery test can take up to two minutes to complete and the keypad will display the voltage of the battery during the test.
Vision-64 User Guide I nd e x Keypad Display ................23 Hi/Lo Temperature ............. 27 All On ................. 5, 8 Icon Descriptions ..............6 Area Keys ..................6 Chime On/Off ..............14 LED Descriptions ..............6 Move To Area ..............14 Status ..................
Page 31
Vision-64 User Guide Holidays ................26 Schedules ................26 Trouble ................23 System Log Email ................... 20 Telephone Numbers Call Forward Off ..............21 Call Forward On ..............21 Domestic ................20 Testing Battery Test ................. 28 Walk Test All Zones ............27 Test Report Send ...................