References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program or service is not intended to state or imply that only IBM’s product, program, or service may be used.
T54A-E.book Page 2 Saturday, February 19, 2000 12:05 PM Setup Hardware Requirements This monitor requires a computer with a suitable on-board sub-system or Video Adapter card that can support XGA 1024 × 768, SVGA 800 x 600, or VGA 640 x 480 at 60 Hz. Handling Instructions Do not support the monitor within the screen area.
T54A-E.book Page 3 Saturday, February 19, 2000 12:05 PM Adjusting the Monitor Position Viewing Angle You can tilt the screen backward and forward as shown below. Working Practices Rest This section gives advice on how you can Take regular breaks. Vary your posture, stand up and stretch occasionally as work comfortably and reduce prolonged use of computer workstations can be tiring.
T54A-E.book Page 4 Saturday, February 19, 2000 12:05 PM Eyesight Working with monitors, in common with any prolonged close work, can be visually demanding. Look away from the screen periodically and have your eyesight checked regularly. Screen settings Set the screen brightness and contrast to a comfortable level. You may have to adjust this as the lighting changes during the day.
T54A-E.book Page 5 Saturday, February 19, 2000 12:05 PM Connecting your Monitor Be sure to read the ‘Safety Information’ at the front of this User Guide before carrying out this procedure. The AC adapter and signal cable are connected to your monitor.
To use the Plug and Play feature in Windows 95 or Windows 98, files should This section must be completed before be loaded from the IBM Flat Panel Monitor Installation diskette: continuing with the Windows 95 or Windows 98 Auto Setup on Page 10.
To use the Plug and Play feature in Windows 2000, files should be loaded This section must be completed before from the IBM Flat Panel Monitor Installation diskette. continuing with the Windows 2000 confguring for your monitor on page 10.
Setup, the settings are stored and used each time you turn on the monitor. Windows 98 has been run. (see page 6) In order to optimise the displayed image a set-up utility is provided on the IBM Monitor Installation Diskette. Operation of the utility is dependent on the The Setup Utility operating system on your PC.
PC. Wait approximately 15 minutes, until the monitor warms up. Insert the diskette labelled ‘IBM Flat Panel Monitor Installation Diskette into the diskette drive. Display the command prompt screen of the DOS full-screen display.
Drag the icon bar and tool bar, if they are displayed, to the bottom of the screen. Insert the diskette labelled ‘IBM Flat Panel Monitor Installation Disk’ into the diskette drive. Check the operating system installed on your PC and follow the instructions from the table below.
T54A-E.book Page 11 Saturday, February 19, 2000 12:05 PM You have completed the monitor setup for Windows. If you use other operat- ing systems, perform the appropriate for those systems, also: see ETUP Auto Setup for DOS on page 9.
T54A-E.book Page 12 Saturday, February 19, 2000 12:05 PM Normally, you can complete the setup procedure using if your screen image is still distorted after you perform setup diskette does not run on your system, perform If the monitor is in standby mode (STANDBY ON), it might automatically turn off while you are waiting for it to...
T54A-E.book Page 13 Saturday, February 19, 2000 12:05 PM Adjusting Your LCD Monitor User controls User control features Operation The image is already • optimized for many display • modes, however the user controls can be used to adjust the image to your liking. Icon Control Displays the OSD main menu...
T54A-E.book Page 14 Saturday, February 19, 2000 12:05 PM The settings are saved • after adjustment and when exiting the OSD and will be effective thereafter. Note: After making adjustments, the Power indicator LED will briefly OSD Lock / Unlock This feature allows you to secure the current control settings, while allowing the user to adjust Brightness and Contrast, so that they cannot be inadvertently changed.
T54A-E.book Page 15 Saturday, February 19, 2000 12:05 PM On-screen display (OSD) controls The settings adjustable with the user controls are viewed through the On- Screen Display (OSD). Press any of the OSD buttons to activate the OSD. The LCD monitor needs Initial appearance of OSD time to become thermally stable the first time you turn it on...
T54A-E.book Page 16 Saturday, February 19, 2000 12:05 PM OSD Icon IMAGE LOCK (continued) IMAGE POSITION COLOR Description Sub-menu(s) Manual - • • Moves the screen left and right or up H-Position and down. V-Position Select the Color Mode you find most Color Mode comfortable and then fine tune the colors using the User Color Mode...
T54A-E.book Page 17 Saturday, February 19, 2000 12:05 PM OSD Icon RESET INFORMATION LANGUAGE OSD MENU POSITION Description Sub-menu(s) Resets the Brightness, Contrast and Color Reset Color settings. Resets the Image position settings Geometry Reset Shows information about the addressability and the horizontal and vertical frequencies of the images received from the computer or video board.
T54A-E.book Page 18 Saturday, February 19, 2000 12:05 PM Display modes The display mode the monitor uses is controlled by the computer. Therefore, you should refer to your computer documentation for details on how to change display modes. The image size, position and shape may change when the display mode changes.
T54A-E.book Page 20 Saturday, February 19, 2000 12:05 PM If you have a problem setting up or using your monitor, you may be able to solve it yourself. Before calling your retailer or IBM, try the suggested actions that are appropriate to your problem.
T54A-E.book Page 21 Saturday, February 19, 2000 12:05 PM For image problems, you may want to run AUTO Setup again before consulting to this section. In most cases, AUTO SETUP can fix the problems. See Auto Setup on page 8 for details. Possible Problem Cause...
More help, late-breaking Removing the stand and cables news and details of the Alternative stands for your IBM Flat Panel Monitor may be available from latest accessories for these products may be found on the specialist suppliers.
11. Insert the three tabs at the top of the cable cover into the slots in the To obtain the correct cables and/or to get further instructions on installing them, call the IBM HELPCENTER at the above numbers or contact your dealer, retailer, or other IBM authorized Servicer.
T54A-E.book Page 24 Saturday, February 19, 2000 12:05 PM Specifications This color monitor (Type-model 9511-Axx) uses a 15-inch TFT LCD Dimensions Weight Tilt Image Power Input Power consumption Power Consumption figures are for the monitor and the power supply combined. Video Input Communications Supported Display...
T54A-E.book Page 25 Saturday, February 19, 2000 12:05 PM Warranty Statements Your Installation Diskette includes translation of IBM’s Statement of Warranty in following languages: Arabic Brazilian portuguese Bulgarian Chinese Croatian Czech Danish Dutch English Finnish French German Greek Hebrew Hungarian...
T54A-E.book Page 26 Saturday, February 19, 2000 12:05 PM Spanish Swedish Taiwanese Turkiye Statement of Warranty: Turkish English United States, Puerto Rico and Candada Statem ent of Lim ited Warranty: English French Canadian Z1255697.spa.html Z1255697.swe.html Z1255697.tai.html Z1255698.tur.html Z1255698.eng.html Z1254753.eng.html Z1254753.fca.html...