HIKVISION DS-2CD2012-I Quick Operation Manual
Network bullet camera
Hide thumbs
Also See for DS-2CD2012-I:
- User manual (95 pages) ,
- Quick operation manual (22 pages) ,
- Installation manual (15 pages)
Advertisement
Table of Contents
Advertisement
Chapters
Table of Contents
Related Manuals for HIKVISION DS-2CD2012-I
Summary of Contents for HIKVISION DS-2CD2012-I
- Page 1 Camera Network Bullet Camera Quick Operation Guide UD.6L0201B1268A01...
- Page 2 About This Document This manual applies to the following models. Model DS-2CD2012-I DS-2CD2032-I DS-2CD2010-I This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice.
-
Page 3: Regulatory Information
Network Bullet Camera·Quick Operation Guide 0501001031101 Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 4 Network Bullet Camera·Quick Operation Guide 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
-
Page 5: Safety Instruction
Network Bullet Camera· Quick Operation Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. - Page 6 Network Bullet Camera· Quick Operation Guide ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
- Page 7 Network Bullet Camera· Quick Operation Guide ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30℃~+60℃,or -40°C ~ 60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation.
- Page 8 Network Bullet Camera· Quick Operation Guide Table of Contents 1 Appearance Description ..............8 2 Installation ..................9 3 Setting the Network Camera over the LAN ........12 4 Accessing via Web Browser ............17...
-
Page 9: Appearance Description
Network Bullet Camera· Quick Operation Guide 1 Appearance Description Figure 1-1 Bullet Camera Overview Table 1-1 Description Description Sun Shield Back Box Grounding Screw Adjustable Bracket Mounting Base Reset... -
Page 10: Installation
Network Bullet Camera· Quick Operation Guide 2 Installation Before you start: Make sure the device in the package is in good condition and all the assembly parts are included. Make sure all the related equipment is power-off during the installation. - Page 11 Network Bullet Camera· Quick Operation Guide ● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection. ● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS.
- Page 12 Network Bullet Camera· Quick Operation Guide Figure 2-2 Secure the Camera to the Ceiling Adjust the Lens. Loosen the adjustable nut on the bracket. Adjust the panning angle [0~360°] of the camera. Adjust the tilting angle [0~90°] of the camera. Rotate 0~360°...
-
Page 13: Setting The Network Camera Over The Lan
Network Bullet Camera· Quick Operation Guide 3 Setting the Network Camera over the Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or PCNVR software to search and change the IP of network camera. - Page 14 Network Bullet Camera· Quick Operation Guide Use PCNVR software and to list the online devices. Please refer to the user manual of PCNVR client software for detailed information. 2. Change the IP address and subnet mask to the same subnet as of your PC.
- Page 15 Network Bullet Camera· Quick Operation Guide Figure 3-2 Search Online Devices Device can be searched and displayed in the list in 15 seconds after it goes online; it will be removed from the list in 45 seconds after it goes offline. Search online devices manually: You can also click to refresh the online device...
-
Page 16: Modify Device Information
Network Bullet Camera· Quick Operation Guide You can click on each column heading to order the information; you can click to show the device table and hide the network parameter panel on the right side, or click to show the network parameter panel. ... - Page 17 Network Bullet Camera· Quick Operation Guide Figure 3-4 Modify Network Parameters 3. Enter the IP address of network camera in the address field of the web browser to view the live video. The default value of the IP address is “192.0.0.64”. The default user name is “admin”, and password is “12345”.
-
Page 18: Accessing Via Web Browser
Network Bullet Camera· Quick Operation Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari... - Page 19 Network Bullet Camera· Quick Operation Guide Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
- Page 20 Network Bullet Camera· Quick Operation Guide Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in (1)
- Page 21 Network Bullet Camera· Quick Operation Guide Figure 4-4 Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2-4 to login. For detailed instructions of further configuration, please refer to the user manual of network camera.
- Page 22 Network Bullet Camera· Quick Operation Guide...