Programming - Amana RCS10 Owner's Manual

Programming

Preprogrammed Times and Cook Level
All preprogrammed pads arrive set at full power.
Pads Times
1 10 sec.
2 20 sec.
3 30 sec.
4 45 sec.
5 1 min.
Using X2 Pad (some models)
X2 pad increases the cooking time when
cooking more than one item at a time is
necessary. The amount of added time when
the X2 pad is pressed is a percent of the original
preprogrammed cooking time. The percent can be set
from 10% to 100% with the default at 80%. The percent
of the time added can be changed for individual cooking
programs.
Press X2 pad before pressing memory pad. For
example, press X2 pad and then memory pad 3. Pad 3
normally cooks for 30 seconds. When the X2 pad is
pressed before memory pad 3, 54 seconds displays
because it added 24 seconds, (80% of 30 sec. =24
sec.).
Manual Time Entry
Manual Time Entry feature allows the operator to enter
time and power levels, and heat without changing the
preprogrammed pads. Example: Heat for 30 seconds at
20% power.
1. Open oven door, place food in oven, and
close door.
• Display shows "READY". Fan and
light operate.
• If pad is not pressed in 60 seconds,
open and close oven door again.
2. Press TIME ENTRY pad.
• Display shows "0000" and "READY".
3. Press 3 and 0 pad to enter cooking
time.
4. Press POWER LEVEL pad to change
power level.
• Display shows current power level if
other than 100 percent power.
5. Press START pad.
• Oven operates and time counts down.
• Display shows cooking time and "POWER".
• Display shows "POWER" only when microwave
energy is present.
• If power level other than 100 percent power was
programmed, display shows power level. Display
counts down cooking time.
6. Oven stops cooking and oven signal sounds when
cooking timing has elapsed.
Pads Times
6 1:30 min.
7 2 min.
8 3 min.
9 4 min.
0 5 min.
X2
TIME
ENTRY
3
0
DEFROST
20%
START
Memory Pads
Follow instructions below to program cooking times and
power levels for customized cooking. Example: Program
third cooking sequence to heat for 30 seconds at 20%
power.
1. Open oven door.
• Display shows "READY".
• If door is closed or RESET pad is
pressed before finishing programming
sequence, oven exits programming
mode.
2. Press and hold pad 1 for approximately
5 seconds.
• After 5 seconds, signal sounds.
Display shows "P:" ("P:0" if in double
pad programming mode).
3. Press 3 pad to select memory pad.
• Display shows cooking time.
4. Press 3 and 0 pad to enter desired
cooking time.
5. Press POWER LEVEL pad to change
power level.
• Display shows power level if other than
100 percent power.
6. Press START pad to save new cooking
time and power level in oven memory.
• Display shows "P:".
• Repeat step 3–6 to program additional
pads.
7. Press STOP/RESET pad or close oven door to exit
programming mode.
Double Pad Programs (some models)
The oven control can be changed to store up to 100
cooking programs. See the "User's Options" section of
this manual to change oven control.
To create a double pad program, follow the instructions
above except for a change to step #3. When entering the
cooking program number, press 2 memory pads. For
example, press pads 0 and pad 3 to create a new cooking
program. After the program is saved, press pad 0 and pad
3 to start a cooking program.
12
1
3
3
0
DEFROST
20%
START
STOP
RESET