Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Advertisement
Table of Contents
Related Manuals for Avital AVISTART 2501
Summary of Contents for Avital AVISTART 2501
- Page 1 AviStart 2501 Installation Manual - Rev. B 100199...
- Page 2 AviStart 2501 Installation Manual - Rev. B 100199...
-
Page 3: Table Of Contents
Programming Table for System Features ....1 6 Programming Table for Remote Controls ....1 6 AviStart 2501 Installation Manual - Rev. B 100199... -
Page 4: Important Information
6 . Turn off dome light or remove dome light fuse to prevent battery drain. This device complies with Part 15 of the FCC rules. Any changes or modifications made to the system without the express approval of Avital Technologies, Inc. could void the user’s authority to operate this equipment. -
Page 5: Main Wiring Diagram
Main Wiring Diagram AviStart 2501 Installation Manual - Rev. B 100199... -
Page 6: Pin Connector
Parking Light Polarity Input (+) or (-) Select Battery (+) 6 Pin Connector Pin Number Wire Color Description PINK Ignition Output Battery +12 Volts PINK Ignition Output VIOLET Starter Output GRAY Heater/AC Output Not Used AviStart 2501 Installation Manual - Rev. B 100199... -
Page 7: Installation Procedures
4. Sleeve these wires with vinyl tubing or electrical tape and route them through an existing rubber grommet into the engine compartment. 5 . If an existing grommet is not available, drill a hole and install a snap grommet. AviStart 2501 Installation Manual - Rev. B 100199... -
Page 8: Valet Switch
The module can be programmed to turn the ignition "ON" for 15 seconds before the starter engages. This will allow the glow plugs time to warm up and the glow plug light to turn off. AviStart 2501 Installation Manual - Rev. B 100199... -
Page 9: Reverse Light
2. Use a volt/ohmmeter to locate the one wire that will show ground only when the driver door key cylinder is held in the unlock position. Con tin ued on next page. AviStart 2501 Installation Manual - Rev. B 100199... -
Page 10: Factory Alarm Rearm
NOTE: Because these wires can draw high current, we recommend that they be soldered and shrink tubed or taped. If only one 14 ga PINK wire is needed, tape the end of the second 14 ga PINK wire to prevent a short circuit. AviStart 2501 Installation Manual - Rev. B 100199... - Page 11 1 . Use a voltmeter to find the wire that shows +12 volts while the ignition key is in the "CRANK" position only and 0 volts while the key is in the "OFF," "ON" and "RUN" positions. 2. Connect the VIOLET wire to the starter wire. AviStart 2501 Installation Manual - Rev. B 100199...
-
Page 12: Remote Engine Start Neutral Safety Switch Bulletin
Currently, the only vehicles with the combined neutral safety switch that Avital is aware of are General Motors trucks, GM sport utility vehicles, GM column shift passenger cars and Dodge Dakota pickup trucks. There may be additional vehicles with the combined neutral safety switch that require the additional relay. - Page 13 The wire color codes are subject to change. Check all wires with a volt/ohmmeter. If you have any questions, please contact the Avital Technical Support Department. AviStart 2501 Installation Manual - Rev. B 100199...
- Page 14 Gen eral Mo tors Sport Util ity Ve hi cles, Trucks and Col umn Shift Pas sen ger Ve hi cles Dodge Da kota Pickup Trucks AviStart 2501 Installation Manual - Rev. B 100199...
-
Page 15: Tach Wire (Rpm Monitoring)
On most vehicles, the tach wire is easily accessible. If the tach wire is not accessible, there are several alternative choices. Contact Avital Technical Support Department for alternate choices. The following procedure for testing the vehicle tach wire is not exact and may vary with different vehicle make, model and year. -
Page 16: Power And Ground Connections
Features" on page 16. 5 . Press and hold the remote START button. 6. The parking lights will flash two times to confirm the RPMs have been memorized. 7 . Release the START button. AviStart 2501 Installation Manual - Rev. B 100199... -
Page 17: Programmable Features
6 . Follow the "Secondary Action." You will hear a number of beeps to confirm that you have changed the setting of that feature. 7 . Turn the ignition key "OFF." 8 . Repeat steps 1-7 for any other feature you wish to program. AviStart 2501 Installation Manual - Rev. B 100199... -
Page 18: Programming Table For System Features
Press the Green START Button, the Code Learning Button piezo beeper will beep 1 time. Wait 3 seconds, the piezo beeper Instant Remote Control — will beep twice, all codes are Code Deletion erased out of memory. AviStart 2501 Installation Manual - Rev. B 100199... -
Page 19: Avistart 2501 Installation Manual - Rev. B
AviStart 2501 Installation Manual - Rev. B 100199... - Page 20 © 1999 Avital Technologies, Inc., A Division of Clifford Electronics Part Num ber: 32- 2501B/AviStart 2501IM/1099 AviStart 2501 Installation Manual - Rev. B 100199...