1. Manuals
  2. Brands
  3. Valet Manuals
  4. Car Alarm
  5. 562T
  6. Installation manual

Valet 562T Installation Manual

Car security
Hide thumbs
Table of Contents

Advertisement

Quick Links

M M o o d d e e l l 5 5 6 6 2 2 T T
I I n n s s t t a a l l l l a a t t i i o o n n G G u u i i d d e e
NOTE:
This product is intended for installation by a professional installer only!
Any attempt to install this product by any person other than a trained professional
may result in severe damage to a vehicle's electrical system and components.
© 2005 Directed Electronics, Vista, CA
N562T 07-05

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 562T and is the answer not in the manual?

Questions and answers

Related Manuals for Valet 562T

Summary of Contents for Valet 562T

  • Page 1 M M o o d d e e l l 5 5 6 6 2 2 T T I I n n s s t t a a l l l l a a t t i i o o n n G G u u i i d d e e NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional...
  • Page 2 , , 3 3 - - p p i i n n p p o o r r t t ......2 2 5 5 valet/program switch ....5 p p r r o o g g r r a a m m m m i i n n g g j j u u m m p p e e r r s s .
  • Page 3 w w a a r r n n i i n n g g ! ! s s a a f f e e t t y y f f i i r r s s t t The following safety warnings must be observed at all times: ■...
  • Page 4 i i n n s s t t a a l l l l a a t t i i o o n n p p o o i i n n t t s s t t o o r r e e m m e e m m b b e e r r b b e e f f o o r r e e b b e e g g i i n n n n i i n n g g t t h h e e i i n n s s t t a a l l l l a a t t i i o o n n I I M M P P O O R R T T A A N N T T ! ! This product is designed for fuel-injected, automatic transmission vehicles only.
  • Page 5 -inch hole. I I M M P P O O R R T T A A N N T T ! ! When the vehicle is delivered, please show the user where the Valet/Program switch is located and how to disarm the system using the switch.
  • Page 6 s s t t a a t t u u s s L L E E D D Things to remember when positioning the status LED: ■ It should be visible from both sides and the rear of the vehicle, if possible. ■...
  • Page 7 o o b b t t a a i i n n i i n n g g c c o o n n s s t t a a n n t t 1 1 2 2 V V We recommend two possible sources for 12V constant: The (+) terminal of the battery, or the constant 12V supply to the ignition switch.
  • Page 8 control the starter. Instead, the cold start circuit is used to prime the fuel injection system for starting when the vehicle is cold. H H o o w w t t o o f f i i n n d d t t h h e e s s t t a a r r t t e e r r w w i i r r e e w w i i t t h h y y o o u u r r m m u u l l t t i i m m e e t t e e r r : : 1.
  • Page 9 f f i i n n d d i i n n g g t t h h e e R R P P M M i i n n p p u u t t w w i i r r e e To test for a tachometer wire, a multimeter capable of testing AC voltage must be used.
  • Page 10 w w i i r r i i n n g g d d i i a a g g r r a a m m s s p p r r i i m m a a r r y y h h a a r r n n e e s s s s ( ( H H 1 1 ) ) w w i i r r i i n n g g d d i i a a g g r r a a m m The primary harness supplied with this unit is the standard 12-pin harness used by Directed Electronics security systems.
  • Page 11 r r e e m m o o t t e e s s t t a a r r t t r r i i b b b b o o n n h h a a r r n n e e s s s s w w i i r r i i n n g g d d i i a a g g r r a a m m ______ P P I I N N K K / / W W H H I I T T E E ( ( - - ) ) 2 2 0 0 0 0 m m A A P P R R O O G G R R A A M M M M A A B B L L E E A A C C C C / / I I G G N N O O U U T T P P U U T T...
  • Page 12 a a u u x x i i l l i i a a r r y y h h a a r r n n e e s s s s ( ( H H 2 2 ) ) w w i i r r i i n n g g d d i i a a g g r r a a m m ______ V V I I O O L L E E T T / / B B L L A A C C K K ( ( - - ) ) C C H H A A N N N N E E L L 4 4 O O U U T T P P U U T T...
  • Page 13 p p r r i i m m a a r r y y h h a a r r n n e e s s s s ( ( H H 1 1 ) ) w w i i r r e e c c o o n n n n e e c c t t i i o o n n g g u u i i d d e e H H 1 1 / / 1 1 R R E E D D / / W W H H I I T T E E C C h h a a n n n n e e l l 2 2 , , ( ( - - ) ) 2 2 0 0 0 0 m m A A o o u u t t p p u u t t When the system receives the code controlling Channel 2, for longer than 1.5 seconds, the RED/WHITE wire will supply an output as long as the transmission continues.
  • Page 14 H H 1 1 / / 5 5 B B L L A A C C K K ( ( - - ) ) c c h h a a s s s s i i s s g g r r o o u u n n d d c c o o n n n n e e c c t t i i o o n n Remove any paint and connect this wire to bare metal, preferably with a factory bolt rather than your own screw.
  • Page 15 H H 1 1 / / 1 1 0 0 W W H H I I T T E E / / B B L L U U E E ( ( - - ) ) r r e e m m o o t t e e s s t t a a r r t t a a c c t t i i v v a a t t i i o o n n i i n n p p u u t t This input comes from the factory set to 2 activation pulses.
  • Page 16 ( ( - - ) ) L L i i g g h h t t F F l l a a s s h h O O u u t t p p u u t t N N O O T T E E : : For parking light circuits that draw 10 amps or more, the internal jumper must be switched to a (-) light flash output.
  • Page 17 O O R R A A N N G G E E ( ( + + ) ) a a c c c c e e s s s s o o r r y y o o u u t t p p u u t t Connect this wire to the accessory wire in the vehicle that powers the climate control system.
  • Page 18 H H 2 2 / / 4 4 L L I I G G H H T T G G R R E E E E N N / / B B L L A A C C K K ( ( - - ) ) f f a a c c t t o o r r y y a a l l a a r r m m d d i i s s a a r r m m This wire sends a negative pulse every time the remote start is activated or the doors are unlocked.
  • Page 19 r r e e m m o o t t e e s s t t a a r r t t h h a a r r n n e e s s s s ( ( H H 3 3 ) ) w w i i r r e e c c o o n n n n e e c c t t i i o o n n g g u u i i d d e e H H 3 3 / / 1 1 B B L L A A C C K K / / W W H H I I T T E E n n e e u u t t r r a a l l s s a a f f e e t t y y s s w w i i t t c c h h i i n n p p u u t t Connect this wire to the toggle (override) switch as shown in Figure A.
  • Page 20 H H 3 3 / / 4 4 G G R R A A Y Y ( ( - - ) ) h h o o o o d d p p i i n n s s w w i i t t c c h h i i n n p p u u t t This wire MUST be connected to hood pinswitch.
  • Page 21 t t e e s s t t i i n n g g t t h h e e n n e e u u t t r r a a l l s s a a f f e e t t y y s s w w i i t t c c h h 1.
  • Page 22 D D i i a a g g r r a a m m A A - - G G e e n n e e r r a a l l M M o o t t o o r r s s t t r r u u c c k k s s , , s s p p o o r r t t u u t t i i l l i i t t y y v v e e h h i i c c l l e e s s a a n n d d c c o o l l u u m m n n s s h h i i f f t t i i n n g g p p a a s s s s e e n n g g e e r r v v e e h h i i c c l l e e s s : : D D i i a a g g r r a a m m B B - - P P r r e e - - 1 1 9 9 9 9 6 6 D D o o d d g g e e D D a a k k o o t t a a p p i i c c k k u u p p s s w w i i t t h h 2 2 .
  • Page 23 p p a a s s s s l l o o c c k k I I a a n n d d p p a a s s s s l l o o c c k k I I I I ( ( P P L L - - 1 1 a a n n d d P P L L - - 2 2 ) ) The Passlock I and Passlock II systems can be found in the following General Motors vehicles: ■...
  • Page 24 b b y y p p a a s s s s i i n n g g G G M M v v e e h h i i c c l l e e a a n n t t i i - - t t h h e e f f t t s s y y s s t t e e m m s s ( ( V V A A T T S S ) ) Vehicles with the GM VATS (Pass Key) systems have a resistor embedded in the ignition key.
  • Page 25 - - i i n n L L E E D D a a n n d d v v a a l l e e t t / / p p r r o o g g r r a a m m s s w w i i t t c c h h These plug into the module. The status LED plugs into the small two-pin socket, while the Valet/Program switch should be plugged into the larger blue two-pin connector.
  • Page 26 p p r r o o g g r r a a m m m m i i n n g g j j u u m m p p e e r r s s l l i i g g h h t t f f l l a a s s h h ( ( + + ) ) / / ( ( - - ) ) This jumper is used to determine the light flash output polarity.
  • Page 27 Bitwriter® before proceeding. The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to remember whenever programming this unit: Key, Choose, Transmit and Release.
  • Page 28 T T r r a a n n s s m m i i t t . .
  • Page 29 It is possible to access and change any of the feature set- tings using the Valet/Program switch. However, this process can be greatly simplified by using the Bitwriter®. Any of the settings can be changed and then assigned to one of up to four transmitters, a feature called Owner Recognition.
  • Page 30 S S e e l l e e c c t t M M e e n n u u . . Press and H H O O L L D D the Valet/Program switch.
  • Page 31 f f e e a a t t u u r r e e m m e e n n u u s s Factory default settings are indicated in b b o o l l d d in the following feature tables. m m e e n n u u # # 1 1 F F E E A A T T U U R R E E D D E E F F A A U U L L T T - - L L E E D D O O N N S S E E T T T T I I N N G G...
  • Page 32 m m e e n n u u # # 2 2 F F E E A A T T U U R R E E D D E E F F A A U U L L T T - - L L E E D D O O N N S S E E T T T T I I N N G G L L E E D D O O F F F F S S E E T T T T I I N N G G N N U U M M B B E E R R ( ( P P R R E E S S S S C C H H A A N N N N E E L L 1 1 ) )
  • Page 33 1 1 - - 2 2 C C H H I I R R P P S S O O N N / / O O F F F F : : This feature controls the chirps that confirm arming and disarming of the system. A siren or horn must be connected to the H1/10 BROWN wire.
  • Page 34 1 1 - - 1 1 1 1 C C H H A A N N N N E E L L 2 2 L L I I N N K K I I N N G G ( ( N N O O N N E E ) ) / / ARM, DISARM, BOTH: : When programming to validity or timed output this can be programmed to activate when arming or disarming (or both) with the transmitter.
  • Page 35 The default setting is 0.6 seconds. If a differ- ent crank time is desired, select feature 2.5 and (while pressing the Valet/Program switch) advance to the next time by pressing the channel 2 button. The unit will flash the LED to indicate which time is selected. Once the 4.0 second setting is reached the next press of channel 2 will reset the system to the shortest setting.
  • Page 36 To learn the tach signal: Start the vehicle with the key. DRW-96 Within 5 seconds, press and H H O O L L D D the Valet/Program switch. The LED will light constant when the tach signal is learned. Release the Program switch.
  • Page 37 Press and H H O O L L D D the Valet/Program switch. Turn the ignition on and then off. Release the Valet/Program switch. Press and release the Valet/Program switch. The LED will now report the last system shutdown by flashing for one minute in the following grouped patterns:...
  • Page 38 r r e e a a r r d d e e f f o o g g g g e e r r c c o o n n t t r r o o l l The rear defogger output can be remotely turned on/off any time using the remote control. The default setting is O O N N .
  • Page 39 Within 10 seconds, press and release the Valet/Program switch. The status LED will light solid if you have entered Valet Mode, and will go out if you have exited Valet Mode. s s a a f f e e t t y y c c h h e e c c k k Before vehicle reassembly, the remote system must be checked to ensure safe and trouble-free operation.
  • Page 40 f. Activate the remote start system. ■ If the starter engages, immediately step on the brake to shut down the system. If it does engage, recheck the neutral safety input connection. The vehicle may use a mechanical neutral safety switch. (See H3/5 BLACK/WHITE neutral safety switch input in Remote Start Harness Wire Connection Guide section of this guide.) ■...
  • Page 41 lite. Also make sure that the ground wire is going to a chassis ground and not to something under the dash. 3. Check diagnostics. The diagnostics will tell you which shutdown is active or not connected. ■ T T h h e e r r e e m m o o t t e e s s t t a a r r t t w w i i l l l l a a c c t t i i v v a a t t e e b b u u t t t t h h e e s s t t a a r r t t e e r r n n e e v v e e r r e e n n g g a a g g e e s s . . 1.
  • Page 42 w w i i r r i i n n g g q q u u i i c c k k r r e e f f e e r r e e n n c c e e g g u u i i d d e e 4 4 2 2 ©...
  • Page 43 r r e e l l a a y y s s a a t t e e l l l l i i t t e e w w i i r r i i n n g g q q u u i i c c k k r r e e f f e e r r e e n n c c e e g g u u i i d d e e 4 4 3 3 ©...

Table of Contents

Save PDF